1.1 This practice covers the determination of cream time (initiation time), top of cup time, free rise time, free rise height, string gel time (pull time), tack free time, settle back, and free rise density of polyurethane foam formulations using a cup foam test. 1.2 Typical...
1.1 This practice covers procedures for determining the gel times of polyurethane non-foam formulations using commercially available gel test equipment. 1.2 Definitions, terms, and techniques are described along with procedures for calculating sample weights. 1.3 The values stated in...
1.1 This practice describes standardized procedures for the preparation, spraying, packaging, and shipping of fresh spray polyurethane foam (SPF) insulation product samples to be tested for their emissions of volatile organic compounds (VOCs) and semi-volatile organic compounds...
Introduction Note: Nothing in this standard supercedes applicable laws and regulations. Note: In the event of conflict between the English and domestic language, the English language shall take precedence. Purpose. This standard describes a test procedure to determine the foam...
1.1 This test method covers the determination of retained blowing agent in extruded polystyrene foam. 1.2 This test method applies to organic blowing agents which lend themselves to a convenient analysis by gas chromatography. The method is not applicable to blowing agents such...
1.1 This guide covers the removal of test specimens from spray polyurethane foam (SPF) roofing systems in the field for the purpose of examination of an existing system and/or quality assurance for new installations. It describes the types and purposes of sample cuts, visual...
5.1 The yield measurement of aerosol foam sealants is used to indicate the amount of foam sealant that can be obtained from a single container of product. 5.2 The yield does not predict the performance capability of the foam sealant product or its suitability for the intended...
1.1 This specification covers the composition, dimensions, and physical properties of flexible unfaced foam sheet, used to insulate interior surfaces of HVAC ducts, plenums and equipment used for the distribution of conditioned air with a temperature of up to 250°F (121°C). 1.2 HVAC ducts,...
1.1 This test method describes a type of composite foam hardness measurement device known as durometer: Type CF. The procedure for determining indentation hardness of substances comprised of two or more elastomeric materials, one of which is a foam or foam like material....
1.1 This specification covers floor covering having a vinyl plastic wear layer with backing. Products may also contain non-PVC specialty performance top layer(s) or intermediate layer(s), or both. 1.2 Two types of floor covering based on binder content are covered. The floor covering is intended...
1.1 This test method furnishes a way of measuring, in the laboratory, the performance of a foaming chemical to be used in producing foam (air cells) for making cellular concrete. 1.2 This test method includes the following: 1.2.1 Manufacture of laboratory quantities of...
5.1 If the material to be tested includes forming skins, the apparent overall density, or the apparent core density, or both, shall be determined. If the material does not have forming skins, the term overall density is not applicable. 5.2 This test method is also applicable to spray...
1.1 This test method covers the determination of the foaming characteristics of lubricating oils at 24?°C and 93.5?°C. Means of empirically rating the foaming tendency and the stability of the foam are described. 1.2 WARNING-Mercury has been designated by many regulatory...
1.1 This test method describes a method for the evaluation of antifoaming agents used to inhibit or prevent the formation of foam in liquids during mixing at the time of application of agricultural chemicals. This laboratory test method may be used for dilute aqueous solutions...
1.1 This guide is intended to provide information on available methods for the separation and classification of contaminants such as moisture, incompatible polymers, metals, adhesives, glass, paper, wood, chemicals, and original-product residues in recycled plastic flakes or pellets. Although no...
1.1 These test methods apply to slab, bonded, and molded flexible cellular products known as polyurethane foams. Polyurethane foam is generally defined as an expanded cellular product produced by the interaction of active hydrogen compounds, water, and isocyanates. 1.2 The...
5.1 This AE examination is useful to detect micro-damage generation, accumulation, and growth of new or existing flaws. The examination is also used to detect significant existing damage from friction-based AE generated during loading or unloading of these regions. The damage mechanisms that can be...
This specification covers the technical characteristics of and test methods for insulating rods and foam-filled tubes made from fiberglass-reinforce
Narrow Your Results