Note 1: The method of testing for the stress relaxation of plastics has been withdrawn from this standard, and the responsibility has been transferred to Practice D2991. 1.1 These test methods cover the determination of the time dependence of stress (stress...
1.1 This test method covers the measurement of the magnetically induced torque produced by the static magnetic field in the magnetic resonance environment on medical devices and the comparison of that torque to a user-specified acceptance criterion. 1.2 This test...
5.1 The user-level calibration process may be used to verify that the DF tester is functioning properly, that it is within manufacturer specifications, and to perform minor adjustments to bring the unit back into conformance with manufacturer specifications. 5.2 The DF...
1.1 This consumer safety performance specification provides safety and performance requirements for various types of public use play equipment such as, but not limited to, composite play structures, climbing structures, to-fro swings, spring rocking equipment, and slides. It is intended to...
1.1 This is a quantitative method that measures removal torque of continuous thread closures on containers, with matching finishes for predetermined environmental conditions over time. The range of values that can be measured are limited to the equipment used. 1.2 The values...
5.1 The miniature vane shear test may be used to obtain estimates of the undrained shear strength of fine-grained soils. The test provides a rapid determination of the undrained shear strength on undisturbed, or remolded or reconstituted soils. Note 2: Notwithstanding...
1.1 This test method describes the thermal cycling of a Shape Memory Alloy (SMA) specimen through the phase transformation under minimal load transformation after uniaxial deformation. This method will measure residual strain after loading and unloading, recovered strain on heating,...
1.1 This guide covers dynamic testing of vulcanized rubber and rubber-like (both hereinafter termed "rubber" or "elastomeric") materials and products, leading from the definitions of terms used, through the basic mathematics and symbols, to the measurement of stiffness and...
1.1 Weigh-In-Motion-This
5.1 Constant force thermal cycling tests determine the effect of stress on the transformation temperatures, recovered strain and residual strain of a shape memory alloy. The tests may be for one thermal cycle. A standard test method for force controlled repeated...
5.1 The miniature vane shear test may be used to obtain estimates of the undrained shear strength of fine-grained soils. The test provides a rapid determination of the undrained shear strength on undisturbed, or remolded or reconstituted soils. Note 2: Notwithstanding...
5.1 In form-fill operations, sealed areas of packages are frequently subject to disruptive forces while still hot. If the hot seals have inadequate resistance to these forces, breakage can occur during the packaging process. These test methods measure hot seal strength and can be used...
IEC 62912-2:2019 gives requirements for direct current relays intended for safety-related applications in railway signalling installations. This document is applicable to non-proved signalling monostable relays of the spring type, whose return force is generated by elasticity...
This document gives requirements for direct current relays intended for safety-related applications in railway signalling installations. This document is applicable to non-proved signalling monostable relays of the spring type, whose return force is generated by elasticity of...
Note 1: The method of testing for the stress relaxation of plastics has been withdrawn from this standard, and the responsibility has been transferred to Practice D2991. 1.1 These test methods cover the determination of the time dependence of stress (stress...
Note 1: The method of testing for the stress relaxation of plastics has been withdrawn from this standard, and the responsibility has been transferred to Practice D2991. 1.1 These test methods cover the determination of the time dependence of stress (stress...
This standard specifies a method of assessing the holding force of the grounding spring system used in elements of connection. It shall be used together with ISO 2100-100.
INTRODUCTION General During the early phase of the launch (lift-off) a spacecraft will be exposed to severe random acoustic loads. Acoustic loads are the cause of structure-borne random mechanical vibrations inside the spacecraft. Before launch the spacecraft...
Narrow Your Results