1.1 This test method provides for the calculation of the methanol content of commercially available 37?% formaldehyde solutions and is based on the relationship of specific gravity to formaldehyde and methanol content. Separate equations are given for three ranges of methanol: 0?% to...
This specification establishes the requirements for first grade concentrated natural rubber latex of the following categories: Category 1, centrifuged Hevea natural latex preserved with ammonia only or by formaldehyde followed by ammonia; Category 2, creamed Hevea natural latex preserved...
4.1 This test method is useful for determining the formic acid content of glacial acetic acid by chemical means. 4.2 Low molecular weight organic acids (such as acetic and propionic), aldehydes (including formaldehyde and acetaldehyde), ketones, and alcohols (including methyl alcohol) do not...
4.1 This test method is based on the cold oxidation of the glycerol by sodium metaperiodate in a strong acidic medium. Formaldehyde and formic acid are produced in this reaction and the latter is used to measure the glycerol content by titration with standard sodium hydroxide solution, to a...
1.1 This test method covers the measurement of the removal rate of injected challenge chemicals and ultrafine particles by portable air cleaners. This test method also evaluates the extent that portable air cleaners produce a limited set of reaction byproducts: formaldehyde, ozone, nitrogen...
1.1 This test method covers the measurement of the removal rate of injected challenge chemicals and ultrafine particles by portable air cleaners. This test method also evaluates the extent that portable air cleaners produce a limited set of reaction byproducts: formaldehyde, ozone, nitrogen...
1.1 These test methods cover the determination of nonvolatile content of solutions of resins in volatile organic solvents. 1.2 Two test methods are included as follows: 1.2.1 Test Method A-For solutions of non-heat-reactive resins. These solutions contain resins that remain stable and release the...
1.1 The gas chromatography/mass spectrometry (GC/MS) procedure described in this test method is used to determine concentrations of total organic halides and total non-methane hydrocarbons in hydrogen by measurement of individual target halocarbons and hydrocarbons (including formaldehyde),...
1.1 This practice describes procedures for testing the emissions of volatile organic compounds (VOCs), formaldehyde, and other carbonyl compounds, from alkyd paint, latex paint, primer, and other architectural coating samples using a small-scale environmental chamber test facility. 1.2 This...
1.1 This guide provides direction on the measurement of the emissions of volatile organic compounds (VOCs) from indoor materials and products using small-scale environmental test chambers. 1.2 This guide pertains to chambers that fully enclose a material specimen to be tested and does not address...
1.1 This practice is intended for determining volatile organic compound (VOC) emissions from materials and products using emission cells. It can be applied in principle to most construction materials and many products used indoors. Objectives include: 1.1.1 To provide manufacturers, builders, and...
1.1 This practice describes the proper procedures for preserving zooplankton samples with either formaldehyde, ethanol, glutaraldehyde, Lugol's iodine solution, or vinegar (acetic acid). 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are...
1.1 This test method covers the determination of the acidity of commercially available formaldehyde solutions. 1.2 For purposes of determining conformance of an observed or a calculated value using this test method to relevant specifications, test result(s) shall be rounded off "to the...
1.1 This test method employs an FTIR gas analysis system for the determination of trace impurities in gaseous hydrogen fuels relative to the hydrogen fuel quality limits described in SAE TIR J2719 (April 2008) or in hydrogen fuel quality standards from other governing bodies. This FTIR method is...
1.1 This test method is for the determination of formaldehyde evolved from melamine-formaldehyde-based coatings during the cure step. The results may be used to determine the "cure formaldehyde" evolved from a sample under controlled laboratory conditions. 1.2 The values stated...
4.1 Titration techniques using KF reagent are one of the most widely used for the determination of water. 4.2 Although the volumetric KF titration can determine low levels of water, it is generally accepted that coulometric KF titrations (see Test Method E1064) are more accurate for routine...
1.1 This practice describes a micro-scale chamber apparatus and associated procedures for rapidly screening materials and products for their vapor-phase emissions of volatile organic compounds (VOCs) including formaldehyde and other carbonyl compounds. It is intended to complement, not...
1.1 This test method is used to identify and to measure the emissions of volatile organic compounds (VOCs) emitted from samples of cured spray polyurethane foam (SPF) insulation using micro-scale environmental test chambers combined with specific air sampling and analytical methods for VOCs. 1.2...
4.1 Titration techniques using KF reagent are one of the most widely used for the determination of water. 4.2 Although the volumetric KF titration can determine low levels of water, it is generally accepted that coulometric KF titrations (see Test Method E1064) are more accurate for routine...
This specification establishes the requirements for first grade concentrated natural rubber latex of the following categories: Category 1, centrifuged Hevea natural latex preserved with ammonia only or by formaldehyde followed by ammonia; Category 2, creamed Hevea natural latex preserved...
Narrow Your Results