loading
CSA FUEL SAFETY HANDBOOK - Fuel Safety Handbook
April 1, 1998 - CSA

INTRODUCTION The Fuel Safety Handbook is intended to provide the basic information which is essential to gas technicians working with natural gas and propane fuel gases in Ontario. The Fuel Safety Handbook is intended to address the knowledge needed by Ontario gas technicians...

CSA FUEL SAFETY TRAINING - Fuel Safety Training Manual
April 1, 1997 - CSA

Introduction (60 minutes) Using FSW-1, welcome the participants and introduce yourself to the group. Ask the participants to introduce themselves and indicate as to whether they are natural gas or propane fitters. Use the knowledge and skills of your participants as a means of enriching the...

GM FUELS TABS - GM FUELS CUSTOM TABS
GMNA
A description is not available for this item.
J1985_202312 - Fuel Filter - Initial Single-Pass Efficiency Test Method
December 13, 2023 - SAE International

This SAE Standard is intended for all sizes of fuel filters, so a variety of test stands may be required depending upon flow rate. The low contamination level, downstream clean-up filter, and short duration of the test ensure that the particle retention ability of the...

J1696_201704 - Standard Fuel Filter Test Fluid
April 18, 2017 - SAE International

This SAE Standard defines the requirements for fluid to be used in the SAE Fuel Filter Test Procedures.

ARP1827D - Measuring Aircraft Gas Turbine Engine Fine Fuel Filter Element Performance
July 23, 2021 - SAE International

This SAE Aerospace Recommended Practice (ARP) delineates two complementary filter element performance parameters: (1) dirt capacity, and (2) filtration efficiency, and corresponding test procedures. It is intended for non-cleanable (disposable), fine fuel filter elements, rated...

J2793_202005 - Fuel Dispensing Filter Test Methods
May 26, 2020 - SAE International

This SAE Recommended Practice is applicable to gasoline and diesel fuel filters installed on fuel dispensing equipment, mobile or stationary. It describes a set of tests used to characterize the structural integrity, filtration performance, and reaction to water contaminant...

GM229M - Nonmetallic Fuel Filters
October 1, 2012 - GMNA

This specification describes the product requirements for Nylon 12 fuel filters which include test setup, instrumentation, test procedures, and acceptance criteria to be used to functionally test Nylon 12 fuel fíìters. Other documents which describe the performance and...

AIR6985 - Performance Evaluation of Fuel Filter Elements Utilized in Aircraft Gas Turbine Engine and APU Main Fuel Systems
June 10, 2021 - SAE International

This SAE Aerospace Information Report (AIR) reviews performance testing parameters for fuel filter elements utilized in gas turbine engine and APU main fuel systems. The scope is limited to main fuel filter elements rated at 35 μm(c), or finer, which constitute...

ASTM D7650-26 - Standard Practice for Sampling of Particulate Matter in High Pressure Gaseous Fuels with an In-Stream Filter
May 1, 2026 - ASTM International

1.1 This practice is primarily for sampling particulates in gaseous fuels up to a nominal working pressure (NWP) of 70 MPag (10?152 psig) using an in-stream filter. This practice describes sampling apparatus design, operating procedures, and quality control procedures required to...

J905_200909 - Fuel Filter Test Methods
September 28, 2009 - SAE International

The purpose of this fuel filter test method is to provide standardized methods for evaluating the performance characteristics of fuel filters by bench test methods. This, combined with data obtained from application tests, may be used to establish standards of...

GME 06701 - Test of Fuel Filters
January 1, 2007 - GME

This specification details the requirements for fuel filters with regard to filter quality, mechanical strength and weather resistance. Filter replacement intervals are indicated in the relevant CTS (Component Technical Specification).

ASTM D7861-26 - Standard Test Method for Determination of Fatty Acid Methyl Esters (FAME) in Diesel Fuel by Linear Variable Filter (LVF) Array Based Mid-Infrared Spectroscopy
May 1, 2026 - ASTM International

5.1 Biodiesel is a fuel commodity primarily used as a blending component with diesel fuel. It is important to check the concentration of biodiesel in the diesel fuel in order to make sure it is either not below the minimum allowable limit and or does not exceed the maximum...

GMW14839 - Diesel Fuel Filter Water Separator Assembly
April 1, 2018 - GMW
A description is not available for this item.
GMW16438 - Gasoline and Flex Fuel Filter Assembly
November 1, 2017 - GMW
A description is not available for this item.
ASTM D7501-22 - Standard Test Method for Determination of Fuel Filter Blocking Potential of Biodiesel Fuel Blendstock (B100) by Cold Soak Filtration Test (CSFT)
April 1, 2022 - ASTM International

5.1 Some substances that are soluble or appear to be soluble in biodiesel fuel blendstock (B100) at room temperature will, upon cooling to temperatures above the cloud point or standing at room temperature for extended periods, come out of solution. This phenomenon has been observed in both...

ASTM D8659-26 - Standard Test Method for Determination of Count per Volume and Size Distribution of Solid Particles in Light and Middle Distillate Fuels by Direct Imaging Analysis
March 1, 2026 - ASTM International

5.1 This test method is intended for evaluating the cleanliness of fuels identified in the scope. 5.2 Detection of particles can indicate degradation of the fluid condition. Particles, whether organic or inorganic, can cause fouling of fuel filters and damage pumps, injectors,...

ASTM D7501-21 - Standard Test Method for Determination of Fuel Filter Blocking Potential of Biodiesel Fuel Blendstock (B100) by Cold Soak Filtration Test (CSFT)
December 1, 2021 - ASTM International

5.1 Some substances that are soluble or appear to be soluble in biodiesel fuel blendstock (B100) at room temperature will, upon cooling to temperatures above the cloud point or standing at room temperature for extended periods, come out of solution. This phenomenon has been observed in both...

ARP1827C - Measuring Aircraft Gas Turbine Engine Fine Fuel Filter Element Performance
November 20, 2014 - SAE International

This SAE Aerospace Recommended Practice (ARP) delineates two complementary filter element performance ratings: (1) dirt capacity, and (2) filtration efficiency, and corresponding test procedures. It is intended for non-cleanable (disposable), fine fuel filter elements used in...

ASTM D2624-26 - Standard Test Methods for Electrical Conductivity of Aviation and Distillate Fuels
July 1, 2026 - ASTM International

5.1 The ability of a fuel to dissipate charge that has been generated during pumping and filtering operations is controlled by its electrical conductivity, which depends upon its content of ion species. If the conductivity is sufficiently high, charges dissipate fast enough to prevent...

Advertisement