loading
CSA FUEL SAFETY HANDBOOK - Fuel Safety Handbook
April 1, 1998 - CSA

INTRODUCTION The Fuel Safety Handbook is intended to provide the basic information which is essential to gas technicians working with natural gas and propane fuel gases in Ontario. The Fuel Safety Handbook is intended to address the knowledge needed by Ontario gas technicians...

CSA FUEL SAFETY TRAINING - Fuel Safety Training Manual
April 1, 1997 - CSA

Introduction (60 minutes) Using FSW-1, welcome the participants and introduce yourself to the group. Ask the participants to introduce themselves and indicate as to whether they are natural gas or propane fitters. Use the knowledge and skills of your participants as a means of enriching the...

GM FUELS TABS - GM FUELS CUSTOM TABS
GMNA
A description is not available for this item.
ASTM D975-26c - Standard Specification for Diesel Fuel
July 1, 2026 - ASTM International

1.1 This specification covers seven grades of diesel fuel suitable for various types of diesel engines. These grades are described as follows: 1.1.1 Grade No. 1-D S15-A special-purpose, light middle distillate fuel for use in diesel engine applications requiring a fuel with 15...

ASTM D4814-26 - Standard Specification for Automotive Spark-Ignition Engine Fuel
July 1, 2026 - ASTM International

This specification describes the various characteristics and requirements of automotive fuels for use over a wide range of operating conditions in ground vehicles equipped with spark-ignition engines. It provides for a variation of the volatility and water tolerance of automotive fuel...

ASTM D7566-26a - Standard Specification for Aviation Turbine Fuel Containing Synthesized Hydrocarbons
June 15, 2026 - ASTM International

1.1 This specification covers the manufacture of aviation turbine fuel that consists of conventional and synthetic blending components. 1.2 See Appendix X2 for an expanded description of the procedure for the production and blending of synthetic blend components. 1.3 This specification...

ASTM D396-26a - Standard Specification for Fuel Oils
April 1, 2026 - ASTM International

1.1 This specification (see Note 1) covers grades of fuel oil intended for use in various types of fuel-oil-burning equipment under various climatic and operating conditions. These grades are described as follows: 1.1.1 Grades No. 1 of all sulfur grades and No. 2 of all sulfur grades...

ASTM D2700-26b - Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
July 1, 2026 - ASTM International

1.1 This laboratory test method covers the quantitative determination of the knock rating of liquid spark-ignition engine fuel in terms of Motor octane number, including fuels that contain up to 25?% v/v of ethanol. However, this test method may not be applicable to fuel and...

ASTM D2699-26 - Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
July 1, 2026 - ASTM International

1.1 This laboratory test method covers the quantitative determination of the knock rating of liquid spark-ignition engine fuel in terms of Research O.N., including fuels that contain up to 25?% v/v of ethanol. However, this test method may not be applicable to fuel and...

ASTM D975-26b - Standard Specification for Diesel Fuel
March 15, 2026 - ASTM International

1.1 This specification covers seven grades of diesel fuel suitable for various types of diesel engines. These grades are described as follows: 1.1.1 Grade No. 1-D S15-A special-purpose, light middle distillate fuel for use in diesel engine applications requiring a fuel with 15...

ASTM D396-26 - Standard Specification for Fuel Oils
March 1, 2026 - ASTM International

This specification covers grades of fuel oil intended for use in various types of fuel-oil-burning equipment under various climatic and operating conditions. These grades include the following: Grades No. 1 S5000, No. 1 S500, No. 2 S5000, and No. 2 S500 for use in domestic and small...

ASTM D613-26 - Standard Test Method for Cetane Number of Diesel Fuel Oil
June 1, 2026 - ASTM International

1.1 This test method covers the determination of the rating of diesel fuel oil in terms of an arbitrary scale of cetane numbers using a standard single cylinder, four-stroke cycle, variable compression ratio, indirect injected diesel engine. 1.2 The cetane number scale covers the range from...

ASTM D2700-26a - Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
June 1, 2026 - ASTM International

1.1 This laboratory test method covers the quantitative determination of the knock rating of liquid spark-ignition engine fuel in terms of Motor octane number, including fuels that contain up to 25?% v/v of ethanol. However, this test method may not be applicable to fuel and...

ASTM D4054-26 - Standard Practice for Evaluation of New Aviation Turbine Fuels and Fuel Additives
June 1, 2026 - ASTM International

5.1 This practice is intended to describe the data requirements necessary to support the review of new aviation turbine fuels or additives by ASTM members for the developers or sponsors of these new products. 5.2 Its purpose is to guide the sponsor of a new fuel or new fuel...

ASTM D975-26a - Standard Specification for Diesel Fuel
February 1, 2026 - ASTM International

1.1 This specification covers seven grades of diesel fuel suitable for various types of diesel engines. These grades are described as follows: 1.1.1 Grade No. 1-D S15-A special-purpose, light middle distillate fuel for use in diesel engine applications requiring a fuel with 15...

ASTM D2624-26 - Standard Test Methods for Electrical Conductivity of Aviation and Distillate Fuels
July 1, 2026 - ASTM International

1.1 These test methods cover the determination of the electrical conductivity of aviation and distillate fuels with and without a static dissipator additive. The test methods normally give a measurement of the conductivity when the fuel is uncharged, that is, electrically at rest...

ASTM D7566-26 - Standard Specification for Aviation Turbine Fuel Containing Synthesized Hydrocarbons
April 1, 2026 - ASTM International

1.1 This specification covers the manufacture of aviation turbine fuel that consists of conventional and synthetic blending components. 1.2 See Appendix X2 for an expanded description of the procedure for the production and blending of synthetic blend components. 1.3 This specification...

ASTM D2700-26 - Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
May 1, 2026 - ASTM International

1.1 This laboratory test method covers the quantitative determination of the knock rating of liquid spark-ignition engine fuel in terms of Motor octane number, including fuels that contain up to 25?% v/v of ethanol. However, this test method may not be applicable to fuel and...

ASTM E3181-26 - Standard Practice for Determination of the Converted Fraction of Starch and Cellulosic Content From a Fuel Ethanol Production Facility
June 1, 2026 - ASTM International

4.1 In 2014, the U.S. EPA published the final rules adding renewable fuel pathways under the RFS Program. The rules qualified kernel fiber as a cellulosic feedstock meeting the 60?% greenhouse gas (GHG) reduction and qualifies for the generation of D3 RINs. These rules allow for two...

Advertisement