loading
GM AIR_GAGE - Air Pressure Gages
September 1, 2010 - GMNA
A description is not available for this item.
ASTM D6846-02(2026) - Standard Practice for Preparing Prints of Paste Printing Inks with a Printing Gage
June 1, 2026 - ASTM International

1.1 This practice covers the procedure for preparing laboratory prints of paste inks using a printing gage in conjunction with a flat-bed proof press. 1.2 This practice is applicable to the preparation of solid-area prints by direct letterpress or by dry offset on a flat substrate such as...

ASTM E1561-26 - Standard Practice for Analysis of Strain Gage Rosette Data
May 1, 2026 - ASTM International

This practice defines a reference axis for each of the two principal types of rosette configurations and the equations used for three-element strain gage rosette data analysis. The primary uses of this analysis procedure are to determine the directions and magnitudes of the principal surface...

ASTM D4986-26 - Standard Test Method for Horizontal Burning Characteristics of Cellular Polymeric Materials
July 1, 2026 - ASTM International

5.1 This test method provides a means of measuring the time and extent of burning for cellular polymeric materials. It also provides a means of measuring burning rates for materials that continue to burn past the specified gage marks. 5.2 This test method provides a means of comparing the...

ASTM D7192-26 - Standard Test Method for High Speed Puncture Properties of Plastic Films Using Load and Displacement Sensors
July 1, 2026 - ASTM International

4.1 This test method is designed to provide load versus deformation response of plastic films under essentially multi-axial deformation conditions at impact velocities. This test method further provides a measure of the rate sensitivity of the plastic films to impact. 4.2 Multi-axial impact...

ASTM E296-70(2025) - Standard Practice for Ionization Gage Application to Space Simulators
December 1, 2025 - ASTM International

This practice provides application criteria, definitions, and supplemental information to assist the user in obtaining meaningful vacuum ionization gage measurements in space-simulation facilities. Acceptable vacuum-measuring equipment shall consist of those items in which performance is...

ASTM A857/A857M-19(2025) - Standard Specification for Steel Sheet Piling, Cold Formed, Light Gage
November 1, 2025 - ASTM International

1.1 This specification covers cold-formed, light gage carbon steel sheet piling of structural quality for use in the construction of shore walls, trench shoring, wingwalls, bulkheads, and like applications. 1.2 The nominal thickness of material furnished under this specification shall be 0...

ASTM E74-18(2026) - Standard Practices for Calibration and Verification for Force-Measuring Instruments
April 1, 2026 - ASTM International

1.1 The purpose of these practices is to specify procedures for the calibration of force-measuring instruments. Procedures are included for the following types of instruments: 1.1.1 Elastic force-measuring instruments, and 1.1.2 Force-multiplying systems, such as balances and small platform scales....

ASTM D882-26 - Standard Test Method for Tensile Properties of Thin Plastic Sheeting
April 1, 2026 - ASTM International

1.1 This test method covers the determination of tensile properties of plastics in the form of thin sheeting and films (less than 1.0 mm (0.04 in.) in thickness). Note 1: Film is defined in Terminology D883 as an optional term for sheeting having a nominal thickness no greater than 0.25 mm (0.010...

ASTM A6/A6M-26a - Standard Specification for General Requirements for Rolled Structural Steel Bars, Plates, Shapes, and Sheet Piling
April 1, 2026 - ASTM International

1.1 This general requirements specification covers a group of common requirements that, unless otherwise specified in the applicable product specification, apply to rolled structural steel bars, plates, shapes, and sheet piling covered by each of the following product specifications issued by ASTM:...

ASTM B258-18(2026) - Standard Specification for Standard Nominal Diameters and Cross-Sectional Areas of AWG Sizes of Solid Round Wires Used as Electrical Conductors
February 1, 2026 - ASTM International

This specification prescribes the standard nominal diameters and cross-sectional areas of American Wire Gage (AWG) sizes of solid round wires, used as electrical conductors, and gives equations and rules for the calculation of standard nominal mass and lengths, resistances, and breaking or...

ASTM F1498-25 - Standard Specification for Taper Pipe Threads 60° for Thermoplastic Pipe and Fittings
December 1, 2025 - ASTM International

1.1 This specification establishes requirements for dimensions and gaging of taper pipe threads used on threaded plastic pipe and fittings. 1.2 Threads meeting this specification shall only be used on those plastic materials deemed suitable by the manufacturer. 1.3 Specialty threads or threads not...

ASTM F3054-26 - Standard Practice for Operations of Amusement Railway Rides, Devices, and Facilities
February 1, 2026 - ASTM International

1.1 This practice applies to operations of amusement railway ride(s) that have a track gage greater than or equal to 12 in. (305 mm) measured between the heads of the rails. This excludes patron powered ride vehicles specifically designed for children. 1.2 This standard does not apply to the...

ASTM B169/B169M-26 - Standard Specification for Aluminum Bronze Sheet, Strip, and Rolled Bar
January 1, 2026 - ASTM International

This specification establishes the requirements for UNS C61300 and C61400 copper aluminum bronze alloy sheets, strips, and rolled bars. These products are intended for drawing, forming, stamping, and bending applications but not for electrical applications. Each product is hot or cold rolled to...

ASTM E295-82(2025) - Standard Test Method for Measured Speed of Oil Diffusion Pumps
December 1, 2025 - ASTM International

This test method establishes the apparatuses required, calibration and precision of the devices to be used, and the standard procedures for determining the measured speed, or volumetric flow rate, of oil diffusion pumps. This method shall make use of test dome, gage attachment or connecting...

ASTM D7078/D7078M-20(2025) - Standard Test Method for Shear Properties of Composite Materials by V-Notched Rail Shear Method
November 1, 2025 - ASTM International

1.1 This test method covers the determination of the shear properties of high-modulus fiber-reinforced composite materials by clamping the ends of a V-notched specimen between two pairs of loading rails. When loaded in tension, the rails introduce shear forces into the specimen through the specimen...

ASTM A6/A6M-26 - Standard Specification for General Requirements for Rolled Structural Steel Bars, Plates, Shapes, and Sheet Piling
January 1, 2026 - ASTM International

1.1 This general requirements specification2 covers a group of common requirements that, unless otherwise specified in the applicable product specification, apply to rolled structural steel bars, plates, shapes, and sheet piling covered by each of the following product specifications issued by...

ASTM E2368-25 - Standard Practice for Strain Controlled Thermomechanical Fatigue Testing
October 1, 2025 - ASTM International

1.1 This practice covers the determination of thermomechanical fatigue (TMF) properties of materials under uniaxially loaded strain-controlled conditions. A "thermomechanical" fatigue cycle is here defined as a condition where uniform temperature and strain fields over the specimen gage...

ASTM D4414-25 - Standard Practice for Measurement of Wet Film Thickness by Notch Gages
July 1, 2025 - ASTM International

1.1 This practice describes the use of thin rigid metal notched gages, also called step or comb gages, in the measurement of wet film thickness of organic coatings, such as paint, varnish, and lacquer. 1.2 Notched gage measurements are neither accurate nor sensitive, but they...

ASTM D1814-70(2025) - Standard Test Method for Measuring Thickness of Leather Units
August 1, 2025 - ASTM International

4.1 This test method is designed for the routine measurement of the thickness of leather units as a means of production control and determining conformance to specifications. It utilizes a secondary type of gage that is capable of rapid measurement.

Advertisement