1.1 This specification covers a group of common requirements that, unless otherwise specified in the individual product specification, shall apply to steel forgings under any of the following specifications issued by ASTM: ASTM Designation Title A266/A266M Carbon Steel Forgings for Pressure Vessel...
1.1 This specification covers a group of common requirements that, unless otherwise specified in the individual product specification, shall apply to steel forgings under any of the following specifications issued by ASTM: ASTM Designation Title A266/A266M Carbon Steel Forgings for Pressure Vessel...
This practice provides guidelines for acoustic emission (AE) examination or monitoring of structures, such as pressure vessels, piping systems, or other structures that can be stressed by mechanical or thermal means. The basic functions of an AE monitoring system are to detect, locate, and classify...
1.1 These test methods describe the humidity calibration (or conformance) of humidity generators for use with thermogravimetric analyzers and other thermal analysis apparatus. The humidity range covered is 5 % relative humidity (% RH) to 95?% RH and the temperature range is 0 °C to 80 °C. 1...
4.1 This guide is intended for use by both generators and users of analytical results. It is intended to promote consistent demonstration and documentation of the quality of the measurement results and facilitate determination of the validity of measurements for their intended use. 4.2 This...
1.1 These practices describe means for calibrating ambient, workplace or indoor ozone monitors, using transfer standards. 1.2 These practices describe five types of transfer standards: Practice A-Analytical instruments, Practice B-Boric acid potassium iodide (BAKI) manual analytical procedure,...
This specification covers monitoring devices (monitors) for the automatic detection and signaling of low insulation resistance values in idle electrical motors or generators, or both. Monitors are intended for permanent installation in both existing or new panels and controller enclosures...
4.1 Addressing consensus standards with inter-laboratory studies (ILS) and methods specific to an organization. Test methods need to be validated in many cases, in order to be able to rely on the results. This has to be done at the organization performing the tests but is also performed in the...
5.1 Chlorinated compounds can lead to corrosion of equipment and poisoning of the catalyst. Chlorinated compounds also present a health hazard when incompletely combusted. Chlorine content of petroleum products is determined prior to their being recycled. Note 1: Federal Regulations mandate that...
1.1 This guide is intended to provide best practices on how to visualize airflow in a critical area and be read in conjunction with relevant International Organization for Standardization (ISO), U.S. Food and Drug Administration (FDA), and EudraLex requirements for airflow visualization. 1.2 In...
5.1 PCRT Applications and Capabilities-PCRT has been applied successfully to a wide range of NDT applications in the manufacture and maintenance of metallic and non-metallic parts. Examples of anomalies detected are discussed in 1.1. PCRT has been shown to provide cost effective and accurate NDT...
1.1 This practice covers measurement procedures for evaluating certain characteristics of ultrasonic search units (also known as "probes") that are used with ultrasonic testing instrumentation. This practice describes means for obtaining performance data that may be used to define the acoustic and...
1.1 This test method is intended for quantitative determination of effective boron-10 (10B) areal density (mass per area of 10B, usually measured in grams-10B/cm2 ) in aluminum neutron absorbers. The attenuation of a thermal neutron beam transmitted through an aluminum neutron absorber is compared...
1.1 Purpose-The purpose of this guide is to define a commercially useful standard in the United States of America for incorporating building energy performance into an assessment of existing property condition, and specifically into a property condition assessment (PCA) on an existing building...
1.1 This specification2 covers a group of common requirements that, unless otherwise specified in the individual product specification, shall apply to steel forgings under any of the following specifications issued by ASTM: ASTM Designation Title A266/A266M Carbon Steel Forgings for Pressure Vessel...
1.1 This specification2 covers a group of common requirements that, unless otherwise specified in the individual product specification, shall apply to steel forgings under any of the following specifications issued by ASTM: ASTM Designation Title A266/A266M Carbon Steel Forgings for Pressure Vessel...
5.1 PCRT Applications and Capabilities-PCRT PTI examination has been applied successfully to a wide range of parts in manufacturing and maintenance environments. Examples of manufacturing processes, repair processes, and in-service damage mechanisms evaluated with PTI are discussed in 1.1. PCRT has...
1.1 This guide is intended to provide best practices on how to visualize airflow in a critical area and be read in conjunction with relevant International Organization for Standardization (ISO), U.S. Food and Drug Administration (FDA), and EudraLex requirements for airflow visualization. 1.2 In...
1.1 This specification2 covers a group of common requirements that, unless otherwise specified in the individual product specification, shall apply to steel forgings under any of the following specifications issued by ASTM: ASTM Designation Title A266/A266M Carbon Steel Forgings for Pressure Vessel...
1.1 This practice covers ultrasonic examination of turbine-generator retaining rings produced in accordance with Specifications A288 and A289/A289M with an inside diameter to wall thickness ratio equal to or greater than 5:1 and with wall thicknesses from 1?in. to 4 in. [25?mm to 102 mm]. 1...
Narrow Your Results