loading
ASTM D8193-26 - Standard Test Method for Total Oil and Grease (TOG) and Total Petroleum Hydrocarbon (TPH) in Water and Wastewater with Solvent Extraction Using Non-Dispersive Mid-IR Transmission Spectroscopy
May 15, 2026 - ASTM International

1.1 This test method covers the determination of total oil and grease (TOG) that can be extracted from water or wastewater samples by cyclohexane and measured by non-dispersive IR spectroscopy from 1370?cm-1 to 1380?cm-1. Treating the extract with Florisil to remove polar substances prior to...

ASTM D1403-26 - Standard Test Methods for Cone Penetration of Lubricating Grease Using One-Quarter and One-Half Scale Cone Equipment
April 1, 2026 - ASTM International

5.1 These test methods are applicable to greases of National Lubricating Grease Institute (NLGI) consistency numbers 0 to 4 and are intended for use only where the size of the sample prevents the use of Test Methods D217. 5.2 Actual reduced-scale penetration values are not used or...

ASTM D2595-26 - Standard Test Method for Evaporation Loss of Lubricating Greases Over Wide-Temperature Range
July 1, 2026 - ASTM International

1.1 This test method covers the determination of evaporation loss of lubricating greases at temperatures between 93?°C and 316?°C (200?°F and 600?°F). 1.2 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only. 1.3 This standard...

ASTM D1092-26 - Standard Test Method for Measuring Apparent Viscosity of Lubricating Greases
June 1, 2026 - ASTM International

1.1 This test method covers measurement, in poises, of the apparent viscosity of lubricating greases in the temperature range from -54?°C to 38?°C (-65?°F to 100?°F). Measurements are limited to the range from 25?P to 100?000?P at 0.1?s-1 and 1?P to 100?P at 15?000?s-1. Note 1: At very low...

ASTM D2596-26 - Standard Test Method for Measurement of Extreme-Pressure Properties of Lubricating Grease (Four-Ball Method)
March 1, 2026 - ASTM International

5.1 This test method, used for specification purposes, differentiates between lubricating greases having low, medium, and high level of extreme-pressure properties. The results do not necessarily correlate with results from service. 5.2 It is noted that lubricating greases that have...

ASTM D2509-26 - Standard Test Method for Measurement of Load-Carrying Capacity of Lubricating Grease (Timken Method)
March 1, 2026 - ASTM International

1.1 This test method covers the determination of the load-carrying capacity of lubricating greases by means of the Timken Extreme Pressure Tester. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard...

ASTM D3336-26 - Standard Test Method for Life of Lubricating Greases in Ball Bearings at Elevated Temperatures
May 1, 2026 - ASTM International

1.1 This test method covers the evaluation of the performance of lubricating greases in ball bearings operating under light loads at high speeds and elevated temperatures. 1.2 The values stated in SI units are to be regarded as standard. 1.2.1 Exception-The values given in parentheses are...

ASTM C752-18(2026) - Standard Specification for Nuclear-Grade Silver-Indium-Cadmium Alloy
June 1, 2026 - ASTM International

This specification covers silver-indium-cadmium alloy for use as a control material in light-water nuclear reactors. The use of this material in applications is excluded where material strength of this alloy is a prime requisite. Also, this material must be protected from the primary water by a...

ASTM B614-26 - Standard Practice for Descaling and Cleaning Zirconium and Zirconium Alloy Surfaces
April 1, 2026 - ASTM International

This practice covers a cleaning and de-scaling procedure useful to producers, users, and fabricators of zirconium and zirconium alloys for the removal of ordinary shop soils, oxides, and scales resulting from heat treatment operations and foreign substances present as surface contaminants....

ASTM A882/A882M-26 - Standard Specification for Filled Epoxy-Coated Seven-Wire Steel Prestressing Strand
April 1, 2026 - ASTM International

This specification covers filled epoxy-coated seven-wire prestressing steel strands with protective fusion-bonded epoxy coating applied by the electrostatic deposition method. This specification also covers relaxation loss limits for filled epoxy coated strands. Prestressing steel strands shall be...

ASTM D1404/D1404M-99(2025) - Standard Test Method for Estimation of Deleterious Particles in Lubricating Grease
November 1, 2025 - ASTM International

1.1 This test method covers a procedure for the detection and estimation of deleterious particles in lubricating grease. 1.2 This test method is applicable to all lubricating greases. It can also be used to test other semi-solid or viscous materials. Grease fillers, such as...

ASTM D6300-26 - Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products, Liquid Fuels, and Lubricants
March 1, 2026 - ASTM International

1.1 This practice covers the necessary preparations and planning for the conduct of interlaboratory programs for the development of estimates of precision (determinability, repeatability, and reproducibility) and of bias (absolute and relative), and further presents the standard phraseology for...

ASTM D5707-25 - Standard Test Method for Measuring Friction and Wear Properties of Lubricating Grease Using a High-Frequency, Linear-Oscillation (SRV) Test Machine
November 1, 2025 - ASTM International

5.1 This test method can be used to determine wear properties and coefficient of friction of lubricating greases at selected temperatures and loads specified for use in applications where high-speed vibrational or start-stop motions are present for extended periods of time under initial high...

ASTM D942-25a - Standard Test Method for Oxidation Stability of Lubricating Greases by the Oxygen Pressure Vessel Method
December 1, 2025 - ASTM International

1.1 This test method determines resistance of lubricating greases to oxidation when stored statically in an oxygen atmosphere in a sealed system at an elevated temperature under conditions of test. 1.2 The values stated in SI units are to be regarded as standard. No other units of...

ASTM D7876-26 - Standard Practice for Practice for Sample Decomposition Using Microwave Heating (With or Without Prior Ashing) for Atomic Spectroscopic Elemental Determination in Petroleum Products and Lubricants
March 1, 2026 - ASTM International

1.1 This practice covers the procedure for use of microwave radiation for sample decomposition prior to elemental determination by atomic spectroscopy. 1.1.1 Although this practice is based on the use of inductively coupled plasma atomic emission spectrometry (ICP-AES) and atomic absorption...

ASTM F2519-05(2025) - Standard Test Method for Grease Particle Capture Efficiency of Commercial Kitchen Filters and Extractors
August 1, 2025 - ASTM International

1.1 This test method can be used to determine the grease particle capture efficiency of components and systems used in commercial kitchens to capture grease effluent prior to entering the exhaust duct. The results can be used to select a filter system best suited to a particular...

ASTM D942-25 - Standard Test Method for Oxidation Stability of Lubricating Greases by the Oxygen Pressure Vessel Method
October 1, 2025 - ASTM International

1.1 This test method determines resistance of lubricating greases to oxidation when stored statically in an oxygen atmosphere in a sealed system at an elevated temperature under conditions of test. 1.2 The values stated in SI units are to be regarded as standard. No other units of...

ASTM D2783-25 - Standard Test Method for Measurement of Extreme-Pressure Properties of Lubricating Fluids (Four-Ball Method)
December 1, 2025 - ASTM International

1.1 This test method covers the determination of the load-carrying properties of lubricating fluids. The following two determinations are made: 1.1.1 Load-wear index (formerly Mean-Hertz load). 1.1.2 Weld point by means of the four-ball extreme-pressure (EP) tester. 1.2 For the determination of the...

ASTM D4172-25 - Standard Test Method for Wear Preventive Characteristics of Lubricating Fluid (Four-Ball Method)
December 1, 2025 - ASTM International

1.1 This test method covers a procedure for making a preliminary evaluation of the anti-wear properties of fluid lubricants in sliding contact by means of the Four-Ball Wear Test Machine. Evaluation of lubricating grease using the same machine is detailed in Test Method D2266. 1.2 The values...

ASTM D7342-25 - Standard Test Method for Prolonged Worked Stability of Lubricating Grease in Presence of Water (Water Stability Test)
July 1, 2025 - ASTM International

5.1 It is known that contamination by water can affect the shear stability of some greases in service. This test method is widely used to determine the wet shear stability of greases in service. Many grease specifications require these procedures as a wet shear stability test....

Advertisement