1.1 This fire-test-response standard provides for measuring the response of materials exposed to controlled levels of radiant heating with or without an external ignitor. 1.2 This test method is used to determine the ignitability, heat release rates, mass loss rates, effective heat of...
1.1 This practice describes the calculation of the heat of vaporization of a liquid or the heat of sublimation of a solid from measured vapor pressure data. It is applicable to pure liquids, azeotropes, pure solids, and homogenous solid solutions over the temperature range for which...
1.1 This test method covers the determination of the change in linear dimensions of resilient floor tile/plank products after exposure to heat and reconditioning to ambient temperature. 1.2 This test method allows one to also measure curling that can occur after a specimen has been exposed...
1.1 This test method rates the non-steady state thermal resistance or insulating characteristics of flame resistant clothing materials subjected to a continuous, standardized radiant heat exposure. 1.1.1 This test method is not applicable to clothing materials that are not flame resistant....
1.1 This is a fire test response standard. 1.2 This test method describes the measurement of surface flammability of flexible cellular materials. 1.3 This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled...
This documentation has been prepared to achieve Ford's mission of never ending improvement at all Ford plants having Heat Treat operations and all heat treators, Tier 1 and Tier 2, It has been organized in a manner that it will be used as a tool to: Define the requirements for the...
1.1 This test method is designed to provide a means for measuring the dimensional changes of plastic specimens such as shrinkage or expansion, developed under specific heat and water conditionings. 1.2 The values stated in SI units are to be regarded as standard. The values given in...
This specification covers seamless tubes of nickel and nickel alloy for use in condenser and heat-exchanger service. This covers outside diameter and average wall, or outside diameter and minimum wall tube. Tube shall be furnished in the alloys and conditions defined by this specification....
This specification covers 28 grades of seamless and welded titanium alloy tubes for surface condensers, evaporators, and heat exchangers. Seamless tube shall be made from hollow billet by any cold reducing or cold drawing process that will yield a product meeting the requirements prescribed....
This specification applies to heat meters used to measure heat in heat exchange circuits in which energy is absorbed (cooling) or given up (heating) by a flowing liquid. For this specification, the necessary elements of a heat meter consist of a sensor to measure flow of...
1.1 This specification covers a group of common requirements that, unless otherwise specified in the individual product specification, shall apply to steel forgings under any of the following specifications issued by ASTM: ASTM Designation Title A266/A266M Carbon Steel Forgings for Pressure Vessel...
1.1 This test method measures the non-steady state heat transfer through flame-resistant materials for clothing subjected to a continuous, combined convective and radiant heat exposure. 1.1.1 This test method is not applicable to materials that are not flame resistant. Note 1: The...
1.1 This test method measures the non-steady state heat transfer through flame-resistant materials for clothing subjected to a combined convective and radiant heat exposure. 1.1.1 This test method is not applicable to materials that are not flame resistant. Note 1: The determination...
1.1 This test method covers procedures for testing the durability of preassembled, permanently sealed vacuum insulating glass (VIG) units. 1.2 This test method is applicable only to VIG units that are constructed with flat glass lites (glass panes). 1.3 This test method is applicable to units made...
1.1 This test method specifies the apparatus and procedure for determining total heat of hydration of hydraulic cementitious materials at test ages up to 7 days by isothermal conduction calorimetry. 1.2 This test method also outputs data on rate of heat of hydration versus time that...
1.1 This practice describes a procedure for sorting nonferrous metals using the electromagnetic (eddy current) method. The procedure is intended for use with instruments using absolute or comparator-type coils for distinguishing variations in mass, shape, conductivity, and other variables such as...
1.1 This guide covers products with chemesthetic heat sensations where the perception is derived from chemical stimulation of the trigeminal nerve in the nasal or oral cavity and are colloquially described as spicy, pungent, acrid, irritation, or burn. However, as there are no agreed-upon...
This guide covers standard specification for wrought-carbon steel butt-welding seamless or welded fittings specially processed to ensure better notch toughness. Heat treatment shall be required for all types of fittings. Fittings with mandatory radiographic examination of welds shall be...
1.1 This test method is used to measure the thermal protective properties of materials that provide thermal insulation when contact is made with hot surfaces during a limited exposure up to 1 min. 1.1.1 During this limited time exposure, the temperature can reach a threshold approaching 600?°F...