loading
ASTM F877-26 - Standard Specification for Crosslinked Polyethylene (PEX) Hot- and Cold-Water Distribution Systems
August 1, 2026 - ASTM International

This specification covers requirements, test methods, and methods of marking for crosslinked polyethylene plastic hot- and cold-water distribution systems components made in one standard dimension ratio. Components are comprised of tubing and fittings intended for use in residential and commercial,...

ASTM E1868-26 - Standard Test Methods for Loss-On-Drying by Thermogravimetry
July 1, 2026 - ASTM International

5.1 These test methods are used to estimate the amount of volatile materials present in a material. 5.2 These test methods are useful for design purposes, service evaluation, regulatory statutes, manufacturing control, quality control, specification acceptance, development, and research. 5.3 The...

ASTM B70-26 - Standard Test Method for Change of Resistance with Temperature of Metallic Materials for Electrical Heating
April 1, 2026 - ASTM International

2.1 The change in resistance with temperature for heating element materials is a major design factor and may influence material selection. The measurement of this change is essential to ensure that heating elements perform within product design specifications. 2.2 This test method was...

ASTM D787-26 - Standard Specification for Ethyl Cellulose Molding and Extrusion Compounds
July 1, 2026 - ASTM International

This specification covers the standard requirements for plasticized ethyl cellulose thermoplastic compounds suitable for injection molding and extrusion. It does not however include special materials compounded for special applications. Materials shall be ethyl cellulose plastics in the form of...

ASTM E1354-26 - Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter
August 1, 2026 - ASTM International

1.1 This fire-test-response standard provides for measuring the response of materials exposed to controlled levels of radiant heating with or without an external ignitor. 1.2 This test method is used to determine the ignitability, heat release rates, mass loss rates, effective heat of...

ASTM D4713-12(2026) - Standard Test Methods for Nonvolatile Content of Heatset and Liquid Printing Ink Systems
June 1, 2026 - ASTM International

4.1 Nonvolatile content of printing inks is useful for specification acceptance between the producer and the user. 4.2 In order to obtain accurate results for heatset systems within the specified 3?h heating time, the specimen film thickness must be less than 100 g/m2, and the oven must have...

ASTM B76-26 - Standard Test Method for Elevated Temperature Accelerated Life Cycle Testing for Determining Resistance to Oxidation of Nickel-Chromium and Nickel-Chromium-Iron Alloys for Electrical Heating Applications
April 1, 2026 - ASTM International

1.1 This test method? describes a procedure for determining resistance to oxidation of nickel-chromium and nickel-chromium-iron electrical heating alloys at elevated temperatures under intermittent heating. Procedures for a constant-temperature cycle are provided. 1.2 This test method...

ASTM F1939-26 - Standard Test Method for Radiant Heat Resistance of Flame Resistant Clothing Materials with Continuous Heating
June 15, 2026 - ASTM International

5.1 This test method is intended for the determination of the radiant heat resistance value of a material, a combination of materials, or a comparison of different materials used in flame-resistant clothing for workers exposed to radiant thermal hazards. 5.2 This test method evaluates a material's...

ASTM D2595-26 - Standard Test Method for Evaporation Loss of Lubricating Greases Over Wide-Temperature Range
July 1, 2026 - ASTM International

5.1 The loss of volatile materials from greases and oils can adversely affect the original performance characteristics of a lubricant and, therefore, could be a significant factor in evaluating a lubricant for a specific use. Such volatiles can also be considered contaminants in the environment in...

ASTM E834-21(2026) - Standard Practice for Determining Vacuum Chamber Gaseous Environment Using a Cold Finger
July 1, 2026 - ASTM International

5.1 When applied in the case in which there is no test item in the vacuum chamber (such as during bake-out operations), this procedure may be used to evaluate the performance of the vacuum chamber in relation to other data from the same or other chambers given that critical parameters (for example,...

ASTM E1877-21(2026) - Standard Practice for Calculating Thermal Endurance of Materials from Thermogravimetric Decomposition Data
July 1, 2026 - ASTM International

1.1 This practice describes the determination of thermal endurance, thermal index, and relative thermal index for organic materials using the Arrhenius activation energy generated for thermal decomposition measured by thermogravimetry. 1.2 This practice is generally applicable to materials with a...

ASTM D5958-99(2026) - Standard Practices for Preparation of Oil-Based Ink Resin Solutions
June 1, 2026 - ASTM International

5.1 These practices provide means of preparing small quantities of resin solution (in some procedures in an inert gas atmosphere using uniform, controlled heating). 5.2 This practice provides quick ways to prepare a resin solution for quality control testing during the manufacture of resin...

ASTM D7897-26 - Standard Practice for Laboratory Soiling and Weathering of Roofing Materials to Simulate Effects of Natural Exposure on Solar Reflectance and Thermal Emittance
July 1, 2026 - ASTM International

5.1 The solar reflectance of a building envelope surface affects surface temperature and near-surface ambient air temperature. Surfaces with low solar reflectance absorb a high fraction of the incoming solar energy. Sunlight absorbed by a roof or by other building envelope surfaces can be conducted...

ASTM D4309-18(2026) - Standard Practice for Sample Digestion Using Closed Vessel Microwave Heating Technique for the Determination of Total Metals in Water
May 1, 2026 - ASTM International

1.1 This practice covers the general considerations for quantitative sample digestion for total metals in water using closed vessel microwave heating technique. This practice is applicable to surface, saline, domestic, and industrial wastewater. 1.2 Because of the differences among various...

ASTM D4069-95(2026)e1 - Standard Specification for Impregnated Activated Carbon Used to Remove Gaseous Radio-Iodines from Gas Streams
June 1, 2026 - ASTM International

5.1 Activated carbons used in containment systems for nuclear reactors must be capable of functioning under both normal operating conditions and those conditions which may exist following a design basis accident (DBA). Adsorbent beds that are part of recirculatory systems inside containment may be...

ASTM B78-90(2026) - Standard Test Method of Accelerated Life of Iron-Chromium-Aluminum Alloys for Electrical Heating
February 1, 2026 - ASTM International

1.1 This test method covers the determination of the resistance to oxidation of iron-chromium-aluminum electrical heating alloys at elevated temperatures under intermittent heating using a constant-temperature cycle test. This test is used for internal comparative purposes only. 1.2...

ASTM D7876-26 - Standard Practice for Practice for Sample Decomposition Using Microwave Heating (With or Without Prior Ashing) for Atomic Spectroscopic Elemental Determination in Petroleum Products and Lubricants
March 1, 2026 - ASTM International

1.1 This practice covers the procedure for use of microwave radiation for sample decomposition prior to elemental determination by atomic spectroscopy. 1.1.1 Although this practice is based on the use of inductively coupled plasma atomic emission spectrometry (ICP-AES) and atomic absorption...

ASTM D6794-26 - Standard Test Method for Measuring the Effect on Filterability of Engine Oils After Treatment with Various Amounts of Water and a Long (6?h) Heating Time
June 1, 2026 - ASTM International

5.1 It is normal for some of the combustion products of an internal combustion engine to penetrate into the engine lubricant and be retained in it. 5.2 When an engine is run for a period of time and then stored over a long period of time, the by-products of combustion might be retained in the oil...

ASTM D6795-26 - Standard Test Method for Measuring the Effect on Filterability of Engine Oils After Treatment with Water and Dry Ice and a Short (30?min) Heating Time
June 1, 2026 - ASTM International

5.1 It is normal for some of the combustion products of an internal combustion engine to penetrate into the engine lubricant and be retained in it. 5.2 When an engine is run for a period of time and then stored over a long period of time, the by-products of combustion might be retained in the oil...

ASTM D3426-19(2026) - Standard Test Method for Dielectric Breakdown Voltage and Dielectric Strength of Solid Electrical Insulating Materials Using Impulse Waves
June 1, 2026 - ASTM International

5.1 It is possible for insulating materials used in high-voltage equipment to be subjected to transient voltage stresses, resulting from such causes as nearby lightning strokes. This is particularly true of apparatus such as transformers and switchgear used in electrical-power transmission and...

Advertisement