This specification covers requirements, test methods, and methods of marking for crosslinked polyethylene plastic hot- and cold-water distribution systems components made in one standard dimension ratio. Components are comprised of tubing and fittings intended for use in residential and commercial,...
5.1 These test methods are used to estimate the amount of volatile materials present in a material. 5.2 These test methods are useful for design purposes, service evaluation, regulatory statutes, manufacturing control, quality control, specification acceptance, development, and research. 5.3 The...
2.1 The change in resistance with temperature for heating element materials is a major design factor and may influence material selection. The measurement of this change is essential to ensure that heating elements perform within product design specifications. 2.2 This test method was...
This specification covers the standard requirements for plasticized ethyl cellulose thermoplastic compounds suitable for injection molding and extrusion. It does not however include special materials compounded for special applications. Materials shall be ethyl cellulose plastics in the form of...
1.1 This fire-test-response standard provides for measuring the response of materials exposed to controlled levels of radiant heating with or without an external ignitor. 1.2 This test method is used to determine the ignitability, heat release rates, mass loss rates, effective heat of...
4.1 Nonvolatile content of printing inks is useful for specification acceptance between the producer and the user. 4.2 In order to obtain accurate results for heatset systems within the specified 3?h heating time, the specimen film thickness must be less than 100 g/m2, and the oven must have...
1.1 This test method? describes a procedure for determining resistance to oxidation of nickel-chromium and nickel-chromium-iron
5.1 This test method is intended for the determination of the radiant heat resistance value of a material, a combination of materials, or a comparison of different materials used in flame-resistant clothing for workers exposed to radiant thermal hazards. 5.2 This test method evaluates a material's...
5.1 The loss of volatile materials from greases and oils can adversely affect the original performance characteristics of a lubricant and, therefore, could be a significant factor in evaluating a lubricant for a specific use. Such volatiles can also be considered contaminants in the environment in...
5.1 When applied in the case in which there is no test item in the vacuum chamber (such as during bake-out operations), this procedure may be used to evaluate the performance of the vacuum chamber in relation to other data from the same or other chambers given that critical parameters (for example,...
1.1 This practice describes the determination of thermal endurance, thermal index, and relative thermal index for organic materials using the Arrhenius activation energy generated for thermal decomposition measured by thermogravimetry. 1.2 This practice is generally applicable to materials with a...
5.1 These practices provide means of preparing small quantities of resin solution (in some procedures in an inert gas atmosphere using uniform, controlled heating). 5.2 This practice provides quick ways to prepare a resin solution for quality control testing during the manufacture of resin...
5.1 The solar reflectance of a building envelope surface affects surface temperature and near-surface ambient air temperature. Surfaces with low solar reflectance absorb a high fraction of the incoming solar energy. Sunlight absorbed by a roof or by other building envelope surfaces can be conducted...
1.1 This practice covers the general considerations for quantitative sample digestion for total metals in water using closed vessel microwave heating technique. This practice is applicable to surface, saline, domestic, and industrial wastewater. 1.2 Because of the differences among various...
5.1 Activated carbons used in containment systems for nuclear reactors must be capable of functioning under both normal operating conditions and those conditions which may exist following a design basis accident (DBA). Adsorbent beds that are part of recirculatory systems inside containment may be...
1.1 This test method covers the determination of the resistance to oxidation of iron-chromium-alumin
1.1 This practice covers the procedure for use of microwave radiation for sample decomposition prior to elemental determination by atomic spectroscopy. 1.1.1 Although this practice is based on the use of inductively coupled plasma atomic emission spectrometry (ICP-AES) and atomic absorption...
5.1 It is normal for some of the combustion products of an internal combustion engine to penetrate into the engine lubricant and be retained in it. 5.2 When an engine is run for a period of time and then stored over a long period of time, the by-products of combustion might be retained in the oil...
5.1 It is normal for some of the combustion products of an internal combustion engine to penetrate into the engine lubricant and be retained in it. 5.2 When an engine is run for a period of time and then stored over a long period of time, the by-products of combustion might be retained in the oil...
5.1 It is possible for insulating materials used in high-voltage equipment to be subjected to transient voltage stresses, resulting from such causes as nearby lightning strokes. This is particularly true of apparatus such as transformers and switchgear used in electrical-power transmission and...
Narrow Your Results