loading
ASTM F1952-26 - Standard Specification for Helmets Used for Downhill Mountain Bicycle Racing
May 1, 2026 - ASTM International

1.1 This specification covers performance requirements for helmets used by downhill mountain bicycle riders. Studies have shown higher risk to the head and face for this sport as compared to recreational street riding; hence, this specification requires greater impact protection and provides...

ASTM F2032-26 - Standard Specification for Helmets Used for BMX Cycling
May 1, 2026 - ASTM International

1.1 This specification covers performance requirements for helmets used in BMX cycling. Studies have shown higher risk to the head and face for this sport as compared to recreational street riding; therefore, this specification requires impact protection over a larger area of the head than...

ASTM F1898-26 - Standard Specification for Helmets for Non-Motorized Wheeled Vehicles Used by Infants and Toddlers
May 1, 2026 - ASTM International

This specification covers the performance requirements for helmets manufactured for use by infants and toddlers as passengers or operators of non-motorized wheeled vehicles. The performance requirements to which the helmets shall conform include those for headforms, peripheral vision,...

ASTM E3062/E3062M-20(2026) - Standard Specification for Indoor Ballistic Test Ranges for Small Arms and Fragmentation Testing of Ballistic-resistant Items
March 15, 2026 - ASTM International

This specification establishes the indoor ballistic test range requirements for small arms and fragmentation testing of the following ballistic-resistant items: soft body armor, hard armor plates, body armor accessories, shields, and helmets. It specifies critical test range parameters in...

ASTM E3068-20(2026) - Standard Test Method for Contact Measurement of Backface Deformation in Clay Backing During Body Armor Testing
March 15, 2026 - ASTM International

1.1 This test method covers methods for the contact measurement of backface deformation (BFD) in clay backing caused by a test threat that produces a partial penetration in a body armor test item. 1.2 This test method is applicable to testing of planar and nonplanar soft armor and hard armor. 1.3...

ASTM F1492-25 - Standard Specification for Helmets Used in Skateboarding and Trick Roller Skating
September 1, 2025 - ASTM International

These specifications cover the design and performance requirements, and associated test procedures for helmets used in the activities of skateboarding and trick roller skating. When tested, the helmets shall meet specified requirements for the peak acceleration and time duration,...

ASTM E3368/E3368M-25 - Standard Specification for Ballistic-Resistant Helmets Worn by U.S. Public Safety Officers
March 1, 2025 - ASTM International

1.1 This specification specifies minimum performance requirements and test methods for the ballistic resistance of helmets used by U.S. public safety officers and intended to protect the head against handgun and rifle ammunition. 1.1.1 The test methods within this specification were...

ASTM F1447-24 - Standard Specification for Helmets Used in Recreational Bicycling or Roller Skating
November 1, 2024 - ASTM International

This specification covers performance requirements for helmets manufactured for use by recreational bicyclists or roller skaters. This specification recognizes the desirability of lightweight construction and ventilation; however, it is a performance standard and is not intended to restrict...

ASTM E3422/E3422M-24 - Standard Specification for Protective Helmets Worn by Pedestrian Roadway Workers
July 1, 2024 - ASTM International

4.1 The purpose of this specification is to provide performance requirements and test methods for the evaluation of protective helmets worn by pedestrian roadway workers. 4.2 This specification may be used by suppliers, certification or verification bodies, testing laboratories, research and...

ASTM F1045-24 - Standard Performance Specification for Ice Hockey Helmets
November 1, 2024 - ASTM International

1.1 This performance specification2 covers performance requirements for ice hockey helmets. 1.2 The intent of this performance specification is to reduce the risk of injury to the head without compromising the form and appeal of the game. 1.3 This performance specification covers: (1)...

ASTM E3368/E3368M-24 - Standard Specification for Ballistic-Resistant Helmets Worn by U.S. Public Safety Officers
May 1, 2024 - ASTM International

1.1 This specification specifies minimum performance requirements and test methods for the ballistic resistance of helmets used by U.S. public safety officers and intended to protect the head against handgun and rifle ammunition. 1.1.1 The test methods within this specification were...

ASTM E3299/E3299M-24 - Standard Test Methods for Compression Resistance of Helmets
May 1, 2024 - ASTM International

1.1 This standard provides test methods for assessing compression resistance of helmets worn by military, law enforcement, and corrections personnel. These test methods are applicable for many styles of helmet (that is, high-cut, mid-cut, full-cut). 1.2 Three compression test methods...

ASTM F1849-23 - Standard Specification for Helmets Used in Ice Speed Skating (Long Track) and Short Track Speed Ice Skating (Not to Include Hockey)
November 1, 2023 - ASTM International

This specification covers the performance requirements for helmets used by short track speed ice skaters (excluding hockey). The performance requirements to which the helmets shall conform include those for the headform, retention system, impact sites and projections, and impact...

UL 752 - Bullet-Resisting Equipment
October 17, 2023 - ULSE

1.1 These requirements cover materials, devices, and fixtures used to form bullet-resisting barriers which protect against robbery, holdup, or armed attack such as those by snipers. 1.2 This standard can also be used to determine the bullet resistance of building components that do not fit the...

ASTM F910-04(2023) - Standard Specification for Face Guards for Youth Baseball
August 1, 2023 - ASTM International

1.1 This specification covers protective face guards for sports such as youth baseball (batters and baserunners). 1.2 This type of face guard is designed to be attached to a pre-existing helmet. 1.3 The equipment covered by this specification is intended to reduce hazards of injury to the...

ASTM E3368/E3368M-23a - Standard Specification for Ballistic-Resistant Helmets Worn by U.S. Public Safety Officers
May 1, 2023 - ASTM International

1.1 This specification specifies minimum performance requirements and test methods for the ballistic resistance of helmets used by U.S. public safety officers and intended to protect the head against handgun and rifle ammunition. 1.1.1 The test methods within this specification were...

ASTM F2178/F2178M-23a - Standard Specification for Arc Rated Eye or Face Protective Products
September 1, 2023 - ASTM International

1.1 This product specification is used to determine the arc rating and specify the requirements for products intended for use as eye or face protection for workers exposed to electric arcs. The arc rating is determined in the test with an arc which has a heat flux value of 2100 kW/m2 [50 cal/cm2/s]...

ASTM E3368/E3368M-23 - Standard Specification for Ballistic-Resistant Helmets Worn by U.S. Public Safety Officers
January 1, 2023 - ASTM International

1.1 This specification specifies minimum performance requirements and test methods for the ballistic resistance of helmets used by U.S. public safety officers and intended to protect the head against handgun and rifle ammunition. 1.1.1 The test methods within this specification were...

ASTM E3107/E3107M-23 - Standard Test Method for Resistance to Penetration and Backface Deformation for Ballistic-resistant Torso Body Armor and Shoot Packs
May 1, 2023 - ASTM International

1.1 This test method addresses resistance to ballistic penetration and to backface deformation (BFD) for ballistic-resistant torso body armor and shoot packs. 1.2 This test method is intended for testing of soft body armor, hard armor plates, in conjunction with armor, and shoot packs mounted on a...

ASTM E3343/E3343M-23 - Test Methods for Nonballistic-resistant Helmets Worn by Law Enforcement and Corrections
February 1, 2023 - ASTM International

1.1 This standard provides nonballistic test methods and conditioning procedures for assessing head protection (that is, helmet and face shield) worn by law enforcement and corrections officers. 1.1.1 Conditioning procedures are included to assess durability in terms of resistance to...

Advertisement