1.1 This practice describes a method for obtaining constant relative humidity ranging from 30?% to 98?% at temperatures ranging from 0?°C to 70?°C in relatively small containers by means of an aqueous glycerin solution. 1.2 This practice is applicable for closed systems such as environmental...
1.1 This test method covers the determination of mold growth resistance of Wet Blue and Wet White subject to storage and shipping requirements and intended for use in leather manufacturing. This test method may not be suitable to evaluate fungicides that are inactivated by proteins. This includes...
5.1 Tests made on a material under conditions herein prescribed are of considerable value in comparing the relative smoke obscuration characteristics of plastics. 5.2 This test method serves to determine the extent to which plastic materials are likely to smoke under conditions of active burning...
1.1 This test method covers the determination of the resistance of flexible low permeance vapor retarders for thermal insulation as classified in Specification C1136 to elevated temperature and humidity. Water vapor permeance measurement and visual inspection after exposure at elevated...
5.1 Activated carbons used in containment systems for nuclear reactors must be capable of functioning under both normal operating conditions and those conditions which may exist following a design basis accident (DBA). Adsorbent beds that are part of recirculatory systems inside containment may be...
4.1 Many types of printed matter, notably container labels, packaging materials, magazine and book covers, must be resistant to liquid materials that may contact them advertently or inadvertently. This practice permits an assessment of resistance of printed matter to several types of liquids. 4.2...
5.1 Diesel fuel injection equipment has some reliance on lubricating properties of the diesel fuel. Shortened life of engine components, such as diesel fuel injection pumps and injectors, has sometimes been ascribed to lack of lubricity in a diesel fuel. 5.2 The trend of HFRR test results to diesel...
5.1 Diesel fuel injection equipment has some reliance on lubricating properties of the diesel fuel. Shortened life of engine components, such as diesel fuel injection pumps and injectors, has sometimes been ascribed to lack of lubricity in a diesel fuel. 5.2 The trend of HFRR test results to diesel...
4.1 Defacement of paint and coating films by fungal growth (mold, mildew) is a common phenomenon, and defacement by algal growth as referenced in Test Method D5589 can also occur under certain conditions. It is generally known that differences in the environment, lighting, temperature,...
5.1 An important factor affecting the performance of joints of nonbituminous membranes is their ability to remain bonded over the membrane's expected service life. Time-to-failure tests provide a means of characterizing the behavior of joints under constant load over time. 5.2 Creep is a sensitive...
5.1 Photovoltaic modules and components must be resistant to prolonged exposure to solar radiation, moisture, and heat. Degradation of polymeric components, delamination at the encapsulant and other interfaces, and moisture ingress are among the degradation modes known to decrease the output of...
1.1 These test methods describe the humidity calibration (or conformance) of humidity generators for use with thermogravimetric analyzers and other thermal analysis apparatus. The humidity range covered is 5 % relative humidity (% RH) to 95?% RH and the temperature range...
1.1 These test methods cover procedures for testing pressure-sensitive adhesive-coated tapes to be used as electrical insulation. These tapes are classified as follows: 1.1.1 Class 1-Non-elastomeric backings made from materials such as: Paper, flat or creped, Fabric, uncoated or coated, Cellulose...
1.1 This practice covers the procedure for the post installation verification and acceptance of buried pipe deformation using a visible rotating laser light diode(s), a pipeline and conduit inspection analog or digital CCTV camera system and image processing software. The combination CCTV pipe...
5.1 This test method is useful for determining the variability in material and the influence of parameters affecting the stress-strain properties of rubber vulcanizates, for example, temperature, relative humidity, preconditioning of rubber, and so forth. This test method is particularly...
1.1 This specification defines those characteristics that are required of adhesives to be used in the repair of sandwich panels for durable, rigidwall, relocatable structures. 1.1.1 This specification covers two-part epoxy adhesive suitable for bonding aluminum alloy facings to nonmetallic core,...
1.1 This specification covers the minimum requirements for, and methods of, application of gypsum veneer base for gypsum veneer plasters. 1.2 Gypsum veneer base shall not be used as a base for direct adhesive application of ceramic, metal, or plastic tile in areas exposed to abnormal moisture or...
1.1 This specification covers the requirements for an epoxy resin system intended for the repair of sandwich panels for durable, rigidwall, relocatable structures. It must be usable in a field environment and shall not require the use of special equipment such as autoclaves or presses. The epoxy...
This specification covers electronic instruments intended for intermittent monitoring of patient temperatures. The temperature range of the instrument shall display temperature within the specific range requirement and regards to its accuracy, no individual reading shall be in error by more than...
This specification covers the passivation by electropolishing of stainless steel alloys in the 200, 300, and 400 series, as well as precipitation-harden
Narrow Your Results