loading
ASME ANDE-1 - ASME Nondestructive Examination and Quality Control Central Qualification and Certification Program
January 1, 2020 - ASME

(a) This Standard includes both performance-based and prescriptive requirements to be used for an ASME Nondestructive Examination (NDE) and Quality Control (QC) Central Qualification and Certification Program that applies to NDE personnel and QC inspection personnel. (b)...

AND 10050 - BOSSES, STANDARD DIMENSIONS FOR GASKET SEAL STRAIGHT THREAD
October 25, 2018 - NPFC
A description is not available for this item.
API OIL WELL CEMENT - OIL-WELL CEMENTING PRACTICES IN THE UNITED STATES
January 1, 1959 - API

FOREWORD: Each year in the United States several thousand wells are drilled and completed - some productive of oil or gas and some dry - and during this drilling and completion most of these wells are cased, with the casing set in the bore hole surrounded...

ASTM C1457-26 - Standard Test Method for Determination of Total Hydrogen Content of Uranium Oxide Powders and Pellets by Carrier Gas Extraction
July 1, 2026 - ASTM International

1.1 This test method applies to the determination of hydrogen in nuclear-grade uranium oxide powders and pellets to determine compliance with specifications. Gadolinium oxide (Gd2O3) and gadolinium oxide-uranium oxide powders and pellets may also be analyzed using this...

ASTM D8236-26 - Standard Practice for Preparing an Equilibrium Liquid/Vapor Sample of Live Crude Oil, Condensates, or Liquid Petroleum Products Using a Manual Piston Cylinder for Subsequent Liquid Analysis or Gas Analysis
May 1, 2026 - ASTM International

5.1 This practice allows for compositional analysis of the gases in equilibrium with crude oil, condensate, and liquid petroleum products at a 4:1 vapor/liquid ratio at ambient temperature for analysis using typical instrumentation (RGA) already available in typical refinery...

AND 10104 - TUBING, STEEL, CORROSION-RESISTANT, ROUND, STANDARD DIMENSIONS FOR
May 6, 1994 - NPFC
A description is not available for this item.
AND 10367 - TOLERANCES-ALLOY STEEL SHEET AND STRIP
January 10, 1994 - NPFC
A description is not available for this item.
ASTM D5958-99(2026) - Standard Practices for Preparation of Oil-Based Ink Resin Solutions
June 1, 2026 - ASTM International

1.1 These practices describe laboratory procedures for preparing an oil-based ink resin solution in a high-boiling solvent using four pieces of lab equipment: (1) A hot oil bath (Sections 4 to 11), (2) A stirrer/hot plate (Sections 12 to 16), (3) An industrial blender (Sections 17 to...

AND 20006 - DRIVE-TYPE XVI ENGINE ACCESSORY
May 22, 1989 - NPFC
A description is not available for this item.
API GASOLINE MARKETING - Gasoline Marketing in the 1980s: Structure, Practices, and Public Policy
May 1, 1988 - API

Introduction and Summary Gasoline marketing in this country has undergone significant changes in the last 15 years. In response to these changes, some dealers and other market participants have called for the enactment of divorcement and open supply legislation at both the...

AND 10476 - WASHER - LIMITATIONS ON USAGE OF LOCK
December 18, 1987 - NPFC
A description is not available for this item.
AND 10575 - RIM CONTOUR-9.00-6, TYPE III, LOW PRESSURE, BEACHING GEAR TAIL WHEEL
July 13, 1983 - NPFC
A description is not available for this item.
AND 10566 - RIM CONTOURS-15.50-20 AND 17.00-20, TYPE III, LOW PRESSURE, MAIN LANDING GEAR WHEEL.
June 14, 1983 - NPFC
A description is not available for this item.
AND 10459 - CONNECTORS - ELECTRICAL, PLUGS, INTEGRAL MOUNTING
March 30, 1982 - NPFC
A description is not available for this item.
AND 20000 - DRIVE - TYPE X ENGINE ACCESSORY
April 29, 1980 - NPFC
A description is not available for this item.
AND 10481 - STANDARD DIMENSIONING SYSTEM FOR EXTRUDED SECTIONS
May 9, 1979 - NPFC
A description is not available for this item.
AND 10068 - NUTS AND PLATE NUTS - SELF LOCKING, FUNCTIONAL LIMITATIONS OF
October 13, 1977 - NPFC
A description is not available for this item.
AND 10003 - MOUNTING PAD AND DRIVE - AIRCRAFT ENGINE FUEL PUMP
October 9, 1973 - NPFC
A description is not available for this item.
AND 10201 - SCREENS AND GASKETS - DESIGN REQUIREMENTS FOR CARBURETOR
October 9, 1973 - NPFC
A description is not available for this item.
Advertisement