loading
ASTM D7459-25 - Standard Practice for Collection of Integrated Samples for the Speciation of Biomass (Biogenic) and Fossil-Derived Carbon Dioxide Emitted from Stationary Emissions Sources
August 1, 2025 - ASTM International

1.1 This practice defines specific procedures for the collection of gas samples from stationary emission sources for subsequent laboratory determination of the ratio of biomass (biogenic) carbon to total carbon (fossil derived carbon plus biomass or biogenic carbon) in accordance with Test Methods...

ASTM C618-25 - Standard Specification for Coal Ash and Raw or Calcined Natural Pozzolan for Use in Concrete
January 1, 2025 - ASTM International

1.1 This specification covers coal ash and raw or calcined natural pozzolan, for use in concrete where cementitious or pozzolanic action, or both, is desired, or where other properties normally attributed to coal ash or natural pozzolans may be desired, or where both objectives are to be achieved....

ASTM C1234-24 - Standard Practice for Preparation of Oils and Oily Waste Samples by High-Pressure, High-Temperature Digestion for Trace Element Determinations
October 1, 2024 - ASTM International

5.1 This practice is useful for preparation of difficult-to-digest, primarily oils and oily wastes, specimens for trace element determinations of up to 28 elements by atomic absorption or plasma emission techniques. Specimen preparation by high-pressure ashing is primarily applicable to specimens...

ASTM D6866-24a - Standard Test Methods for Determining the Biobased Content of Solid, Liquid, and Gaseous Samples Using Radiocarbon Analysis
December 1, 2024 - ASTM International

1.1 This standard is a test method that teaches how to experimentally measure biobased carbon content of solids, liquids, and gaseous samples using radiocarbon analysis. These test methods do not address environmental impact, product performance and functionality, determination of geographical...

ASTM D7459-08(2024) - Standard Practice for Collection of Integrated Samples for the Speciation of Biomass (Biogenic) and Fossil-Derived Carbon Dioxide Emitted from Stationary Emissions Sources
September 1, 2024 - ASTM International

1.1 This practice defines specific procedures for the collection of gas samples from stationary emission sources for subsequent laboratory determination of the ratio of biomass (biogenic) carbon to total carbon (fossil derived carbon plus biomass or biogenic carbon) in accordance with Test Methods...

ASTM F1322-15(2024) - Standard Guide for Selection of Shipboard Incinerators
January 1, 2024 - ASTM International

1.1 This guide covers selection criteria to assist procurers in selecting the appropriate incinerator for their needs. 1.2 This guide is a companion document to Specification F1323. 1.3 This guide does not apply to incinerator systems on special incinerator ships, for example,...

ASTM D6784-24 - Standard Test Method for Elemental, Oxidized, Particle-Bound and Total Mercury in Flue Gas Generated from Coal-Fired Stationary Sources (Ontario Hydro Method)
March 1, 2024 - ASTM International

5.1 The measurement of particle-bound, oxidized, elemental, and total mercury in stationary-source flue gases provides data that can be used for emissions assessments and reporting, the certification of continuous mercury monitoring systems, regulatory compliance determinations and research...

ASTM D8560-24 - Standard Guide for Determination of Airborne PFAS in the Indoor Air Environment
April 1, 2024 - ASTM International

5.1 Some PFAS have been implicated in adverse human health impacts (4, 5, 6). Therefore, quantifying PFAS concentrations in indoor air is important for accurate and meaningful exposure analysis and risk assessments. 5.2 PFAS found in air can have a wide range of chemical characteristics that will...

ASTM D6866-24 - Standard Test Methods for Determining the Biobased Content of Solid, Liquid, and Gaseous Samples Using Radiocarbon Analysis
February 1, 2024 - ASTM International

1.1 This standard is a test method that teaches how to experimentally measure biobased carbon content of solids, liquids, and gaseous samples using radiocarbon analysis. These test methods do not address environmental impact, product performance and functionality, determination of geographical...

ASTM D7204-23 - Standard Practice for Sampling Waste Streams on Conveyors
November 1, 2023 - ASTM International

4.1 This practice can be used in sampling ash from a kiln or incinerator, soils, and process waste from conveying systems, such as a conveyer and vertical lifts. Some slurries, such as the bottom solids, can be sampled from the quench waters at the end of a kiln. 4.2 This practice can be...

ASTM F1788-22 - Standard Guide for In-Situ Burning of Oil Spills on Water: Environmental and Operational Considerations
September 1, 2022 - ASTM International

1.1 This guide covers the use of in-situ burning to assist in the control of oil spills on water. This guide is not applicable to in-situ burning of oil on land or the disposal of oil or oiled debris in incinerators. 1.2 The purpose of this guide is to provide information that will enable...

ASTM D6866-22 - Standard Test Methods for Determining the Biobased Content of Solid, Liquid, and Gaseous Samples Using Radiocarbon Analysis
March 15, 2022 - ASTM International

1.1 This standard is a test method that teaches how to experimentally measure biobased carbon content of solids, liquids, and gaseous samples using radiocarbon analysis. These test methods do not address environmental impact, product performance and functionality, determination of geographical...

ASTM F1799-97(2021) - Standard Guide for Shipboard Generated Waste Management Audits
January 1, 2021 - ASTM International

1.1 Purpose-This guide covers information for assisting shipowners in planning for costs or scheduling complications during maintenance, repair, modifications, purchase negotiations, or scrapping activities. Removal and disposal of certain materials disturbed during modification, maintenance, or...

ASTM D6866 - Standard Test Methods for Determining the Biobased Content of Solid, Liquid, and Gaseous Samples Using Radiocarbon Analysis
January 15, 2021 - ASTM

This standard is a test method that teaches how to experimentally measure biobased carbon content of solids, liquids, and gaseous samples using radiocarbon analysis. These test methods do not address environmental impact, product performance and functionality, determination of geographical origin,...

ASTM D6866-21 - Standard Test Methods for Determining the Biobased Content of Solid, Liquid, and Gaseous Samples Using Radiocarbon Analysis
January 15, 2021 - ASTM International

1.1 This standard is a test method that teaches how to experimentally measure biobased carbon content of solids, liquids, and gaseous samples using radiocarbon analysis. These test methods do not address environmental impact, product performance and functionality, determination of geographical...

ASTM F1323-14(2020) - Standard Specification for Shipboard Incinerators
February 1, 2020 - ASTM International

This specification covers the design, manufacture, performance, operation, functioning, and testing of incinerators intended to incinerate garbage and other shipboard wastes generated during the ship's normal service (that is, maintenance, operational, domestic, and cargo-associated wastes)....

DS/ISO 13617 - Ships and marine technology – Shipboard incinerators – Requirements
August 13, 2019 - DS

This document covers the design, manufacture, performance, operation, functioning and testing of incinerators intended to incinerate garbage and other shipboard wastes generated during a ship's normal service (i.e. maintenance, operational, domestic and cargo-associated wastes). This...

ISO 13617 - Ships and marine technology - Shipboard incinerators - Requirements
August 1, 2019 - ISO

This document covers the design, manufacture, performance, operation, functioning and testing of incinerators intended to incinerate garbage and other shipboard wastes generated during a ship's normal service (i.e. maintenance, operational, domestic and cargo-associated wastes). This...

IAPMO LAMC - 2020 COUNTY OF LOS ANGELES MECHANICAL CODE
January 1, 2020 - IAPMO

The provisions of this Code shall apply to the erection, installation, alteration, repair, relocation, replacement, addition to, use, or maintenance of any heating, ventilating, cooling, refrigeration systems, incinerators or other miscellaneous heat-producing appliances. Where, in any...

IAPMO LA MC - 2020 CITY OF LOS ANGELES MECHANICAL CODE
January 1, 2020 - IAPMO

The provisions of this Code shall apply to the addition to or erection, installation, alteration, repair, relocation, replacement, use, or maintenance of heating, ventilation, cooling, refrigeration systems; incinerators; or other miscellaneous heat-producing appliances within this...

Advertisement