loading
ASTM D1492-26 - Standard Test Method for Bromine Index of Aromatic Hydrocarbons by Coulometric Titration
July 1, 2026 - ASTM International

1.1 This test method covers the determination of Bromine Index in aromatic hydrocarbons, their derivatives, and related chemicals. 1.2 This test method is applicable to samples with Bromine Index concentrations to 100 Bromine Index. The limit of detection (LOD) is for 1.5...

ASTM E1877-21(2026) - Standard Practice for Calculating Thermal Endurance of Materials from Thermogravimetric Decomposition Data
July 1, 2026 - ASTM International

1.1 This practice describes the determination of thermal endurance, thermal index, and relative thermal index for organic materials using the Arrhenius activation energy generated for thermal decomposition measured by thermogravimetry. 1.2 This practice is generally applicable to...

ASTM D7237-18(2026) - Standard Test Method for Free Cyanide and Aquatic Free Cyanide with Flow Injection Analysis (FIA) Utilizing Gas Diffusion Separation and Amperometric Detection
July 15, 2026 - ASTM International

5.1 Cyanide and hydrogen cyanide are highly toxic. Regulations have been established to require the monitoring of cyanide in industrial and domestic wastes and surface waters. 5.2 It is useful to determine the aquatic free cyanide to establish an index of toxicity when a wastewater is...

ASTM D3222-21(2026) - Standard Specification for Unmodified Poly(Vinylidene Fluoride) (PVDF) Molding Extrusion and Coating Materials
July 1, 2026 - ASTM International

This specification covers melt processable unmodified poly(vinylidene fluoride) (PVDF) molding, extrusion and coating materials. This specification covers only virgin homopolymer prepared from vinylidene fluoride supplied in form of pellet or powder and shall be free of foreign matter. Two types...

ASTM D2699-26 - Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
July 1, 2026 - ASTM International

5.1 Research O.N. correlates with commercial automotive spark-ignition engine antiknock performance under mild conditions of operation. 5.2 Research O.N. is used by engine manufacturers, petroleum refiners and marketers, and in commerce as a primary specification measurement related to the matching...

ASTM D2700-26b - Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
July 1, 2026 - ASTM International

5.1 Motor O.N. correlates with commercial automotive spark-ignition engine antiknock performance under severe conditions of operation. 5.2 Motor O.N. is used by engine manufacturers, petroleum refiners and marketers, and in commerce as a primary specification measurement related to the matching of...

ASTM C311/C311M-26 - Standard Test Methods for Sampling and Testing Coal Ash or Natural Pozzolans for Use in Concrete
June 15, 2026 - ASTM International

4.1 These test methods are used to develop data for comparison with the requirements of Specification C618 or Specification C1697. These test methods are based on standardized testing in the laboratory and are not intended to simulate job conditions. 4.1.1 Strength Activity Index-The test...

ASTM D975-26c - Standard Specification for Diesel Fuel
July 1, 2026 - ASTM International

This specification covers seven grades of diesel fuel oils suitable for various types of diesel engines. These grades are: Grade No. 1-D S15; Grade No. 1-D S500; Grade No. 1-D S5000; Grade No. 2-D S15; Grade No. 2-D S500; Grade No. 2-D S5000; and Grade No. 4-D. The requirements specified for diesel...

ASTM D6454/D6454M-26 - Standard Test Method for Determining the Short-Term Compression Behavior of Turf Reinforcement Mats (TRMs)
July 1, 2026 - ASTM International

5.1 The compression behavior test for TRMs is intended to be an index test. It is anticipated that the results of the compression behavior test will be used to evaluate product. The results of the analyses also may be used to compare the relative compressive yield points of materials that...

ASTM D4833/D4833M-07(2026) - Standard Test Method for Index Puncture Resistance of Geomembranes and Related Products
June 1, 2026 - ASTM International

5.1 This test method is an index test for determining the puncture resistance of geomembranes and related products. The use of this test method is to establish an index value by providing standard criteria and a basis for uniform reporting. 5.2 This test method is considered...

ASTM D2700-26a - Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
June 1, 2026 - ASTM International

5.1 Motor O.N. correlates with commercial automotive spark-ignition engine antiknock performance under severe conditions of operation. 5.2 Motor O.N. is used by engine manufacturers, petroleum refiners and marketers, and in commerce as a primary specification measurement related to the matching of...

ASTM D6022-26 - Standard Practice for Calculation of Permanent Shear Stability Index
June 1, 2026 - ASTM International

1.1 This practice specifies the procedure for the calculation of Permanent Shear Stability Index (PSSI) of an additive using viscosities before and after a shearing procedure. 1.2 PSSI is calculated for a single blend component and can then be used to estimate the effects of that component...

ASTM C216-26a - Standard Specification for Facing Brick (Solid Masonry Units Made from Clay or Shale)
June 1, 2026 - ASTM International

This specification covers brick intended for use in masonry and supplying structural or facing components, or both, to the structure. Bricks shall be classified according to their resistance to damage by freezing when saturated at a moisture content: Grade SW and Grade MW. The facing bricks shall...

ASTM D4814-26 - Standard Specification for Automotive Spark-Ignition Engine Fuel
July 1, 2026 - ASTM International

1.1 This specification covers the establishment of requirements of liquid automotive fuels for ground vehicles equipped with spark-ignition engines. 1.2 This specification describes various characteristics of automotive fuels for use over a wide range of operating conditions. It provides for a...

ASTM C1088-26 - Standard Specification for Thin Veneer Brick Units Made From Clay or Shale
June 1, 2026 - ASTM International

This specification covers thin veneer brick units made from clay, shale, fire clay, sand, or mixtures thereof, and fired to incipient fusion for use in adhered or fastened veneer applications. The brick units shall be available in both Grades Interior and Exterior of the following types: Type TBS...

ASTM D1655-26b - Standard Specification for Aviation Turbine Fuels
June 15, 2026 - ASTM International

1.1 This specification covers the use of purchasing agencies in formulating specifications for purchases of aviation turbine fuel under contract. 1.2 This specification defines the minimum property requirements for Jet A and Jet A-1 aviation turbine fuel and lists acceptable additives for use in...

ASTM D5776-26 - Standard Test Method for Bromine Index of Aromatic Hydrocarbons by Electrometric Titration
May 1, 2026 - ASTM International

1.1 This test method covers the amount of bromine-reactive material in aromatic hydrocarbons and is thus a measure of trace amounts of unsaturates in these materials. 1.2 This test method is applicable to materials having bromine indexes below 35. Materials with a higher bromine index...

ASTM D2700-26 - Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
May 1, 2026 - ASTM International

5.1 Motor O.N. correlates with commercial automotive spark-ignition engine antiknock performance under severe conditions of operation. 5.2 Motor O.N. is used by engine manufacturers, petroleum refiners and marketers, and in commerce as a primary specification measurement related to the matching of...

ASTM D2227-96(2026) - Standard Specification for Natural Rubber (NR) Technical Grades
April 1, 2026 - ASTM International

This specification covers the minimum physical and chemical requirements for five technical grades of raw natural rubber. Materials are classified into grades according to retained dirt content, ash content, volatile matter content, nitrogen content, initial plasticity, plasticity retention...

ASTM D5405/D5405M-98(2026) - Standard Test Method for Conducting Time-to-Failure (Creep-Rupture) Tests of Joints Fabricated from Nonbituminous Organic Roof Membrane Material
May 1, 2026 - ASTM International

5.1 An important factor affecting the performance of joints of nonbituminous membranes is their ability to remain bonded over the membrane's expected service life. Time-to-failure tests provide a means of characterizing the behavior of joints under constant load over time. 5.2 Creep is a sensitive...

Advertisement