loading
ASTM A788/A788M-26a - Standard Specification for Steel Forgings, General Requirements
August 1, 2026 - ASTM International

This specification covers a group of common requirements that, unless covered by the individual product specification in another ASTM document, applies to steel forgings for general use. Materials shall be produced primarily by either electric-furnace, basic oxygen, vacuum-induction (VIM),...

ASTM A788/A788M-26 - Standard Specification for Steel Forgings, General Requirements
July 1, 2026 - ASTM International

This specification covers a group of common requirements that, unless covered by the individual product specification in another ASTM document, applies to steel forgings for general use. Materials shall be produced primarily by either electric-furnace, basic oxygen, vacuum-induction (VIM),...

ASTM A1014/A1014M-26 - Standard Specification for Precipitation-Hardening Bolting (UNS N07718) for High Temperature Service
July 1, 2026 - ASTM International

This specification covers a precipitation hardening bolting material (UNS N07718) for high temperature service. The alloy shall be multiple melted using consumable electrode practice in the remelt cycle or shall be induction melted under vacuum. Requirements for solution treatment,...

ASTM D525-12a(2025) - Standard Test Method for Oxidation Stability of Gasoline (Induction Period Method)
December 1, 2025 - ASTM International

5.1 The induction period may be used as an indication of the tendency of motor gasoline to form gum in storage. It should be recognized, however, that its correlation with the formation of gum in storage may vary markedly under different storage conditions and with different gasolines.

ASTM F2317/F2317M-26 - Standard Specification for Design of Weight-Shift-Control Aircraft
May 1, 2026 - ASTM International

This specification covers the minimum requirement for designing, testing, and labeling of weight-shift-control aircraft. This specification covers only weight-shift-control aircraft in which flight control systems do not use hinged surfaces controlled by the pilot. Flight requirements are specified...

ASTM A985/A985M-26 - Standard Specification for Steel Investment Castings General Requirements, for Pressure-Containing Parts
April 1, 2026 - ASTM International

This specification covers a group of common requirements that are mandatory for steel castings produced by the investment casting process for pressure-containing parts. Master heats shall be made by the electric furnace process with or without separate refining such as argon-oxygen-decarburization...

ASTM E3209/E3209M-20(2025) - Standard Test Method for Pavement Thickness by Magnetic Pulse Induction
October 1, 2025 - ASTM International

1.1 This test method covers the equipment, field procedures, and interpretation of the results for the pavement thickness measurements produced by a magnetic pulse induction (MPI) device. Magnetic pulse induction devices induce a weak-pulsed magnetic field that causes the...

ASTM A350/A350M-26a - Standard Specification for Carbon and Low-Alloy Steel Forgings, Requiring Notch Toughness Testing for Piping Components
February 15, 2026 - ASTM International

This specification covers several grades of carbon and low alloy steel forged or ring-rolled flanges, forged fittings and valves for low-temperature service. The steel specimens shall be melt processed using open-hearth, basic oxygen, electric furnace or vacuum-induction melting. A...

ASTM A988/A988M-26 - Standard Specification for Hot Isostatically-Pressed Stainless Steel Flanges, Fittings, Valves, and Parts for High Temperature Service
January 1, 2026 - ASTM International

This specification covers hot isostatically-pressed, powder metallurgy, stainless steel piping components such as flanges, fittings, valves, and similar parts, for use in pressure systems and temperature service applications. The specification includes several grades of martensitic, austenitic, age...

ASTM A350/A350M-26 - Standard Specification for Carbon and Low-Alloy Steel Forgings, Requiring Notch Toughness Testing for Piping Components
January 1, 2026 - ASTM International

This specification covers several grades of carbon and low alloy steel forged or ring-rolled flanges, forged fittings and valves for low-temperature service. The steel specimens shall be melt processed using open-hearth, basic oxygen, electric furnace or vacuum-induction melting. A...

ASTM C1853-25 - Standard Test Method for The Determination of Carbon (Total) Content in Mixed Oxide ((U, Pu)O2) Sintered Pellets by Direct Combustion-Infrared Detection Method
November 1, 2025 - ASTM International

1.1 This test method for the determination of carbon in mixed oxide (MOX) pellets consists of combusting carbon with oxygen in a high-frequency induction furnace and subsequent detection of the resulting carbon dioxide (CO2) using a non-dispersive infrared detector (NDIR). Sulfur oxide is...

ASTM A1057/A1057M-25 - Standard Specification for Steel, Structural Tubing, Cold Formed, Welded, Carbon, Zinc-Coated (Galvanized) by the Hot-Dip Process
December 1, 2025 - ASTM International

1.1 This specification covers cold-formed electric resistance or electric induction welded carbon structural steel tubing in round, square, rectangular, or special shapes that are zinc-coated (galvanized) on the exterior surface only, in continuous coating lines by the hot-dip process. The...

ASTM F3732-25 - Standard Performance Specification for Conductive Clothing for Industry Applications
October 1, 2025 - ASTM International

1.1 This performance specification covers minimum requirements to determine the electric performance of conductive clothing. 1.1.1 Type 1 conductive clothing is intended to be used by workers as protection from electric field strength for applications in ac systems up to 800 kV, rms, at 50/60 Hz...

ASTM A646/A646M-25 - Standard Specification for Premium Quality Alloy Steel Blooms and Billets for Forgings
November 1, 2025 - ASTM International

1.1 This specification covers premium quality alloy steel semifinished rolled or forged blooms and billets for reforging into critical parts. 1.2 Blooms and billets, hereinafter referred to as blooms, are semifinished steel products, hot rolled or forged to approximate cross-sectional dimensions....

ASTM D7098-25 - Standard Test Method for Oxidation Stability of Lubricants by Thin-Film Oxygen Uptake (TFOUT) Catalyst B
October 1, 2025 - ASTM International

1.1 This test method covers the oxidation stability of lubricants by thin-film oxygen uptake (TFOUT) Catalyst B. This test method evaluates the oxidation stability of petroleum products, and it was originally developed as a screening test to indicate whether a given re-refined base stock could be...

ASTM D4818-21(2025) - Standard Classification for Rubber Compounding Materials—Vulcanization Accelerators
November 1, 2025 - ASTM International

3.1 Class 1, Sulfenamides: 3.1.1 As a group, the 2-benzothiazyl sulfenamides are the principle sulfur vulcanization accelerators used in the rubber industry today. The role of these materials in vulcanization is dual. They provide scorch time (delay period) in the crosslinking or vulcanization...

ASTM D6201-25 - Standard Test Method for Dynamometer Evaluation of Unleaded Spark-Ignition Engine Fuel for Intake Valve Deposit Formation
November 1, 2025 - ASTM International

1.1 This test method covers an engine dynamometer test procedure for evaluation of intake valve deposit formation of unleaded spark-ignition engine fuels.2 This test method uses a Ford Ranger 2.3?L four-cylinder engine. This test method includes detailed information regarding the procedure,...

ASTM A480/A480M-25b - Standard Specification for General Requirements for Flat-Rolled Stainless and Heat-Resisting Steel Plate, Sheet, and Strip
September 1, 2025 - ASTM International

This specification covers general requirements for flat-rolled stainless and heat-resisting steel plate, sheet, and strip. The steel shall be made by one of the following processes: electric-arc, electric-induction, or other suitable processes. Heat and product analyses shall conform to the...

ASTM A989/A989M-25 - Standard Specification for Hot Isostatically-Pressed Alloy Steel Flanges, Fittings, Valves, and Parts for High Temperature Service
September 1, 2025 - ASTM International

This specification covers hot isostatically-pressed, powder metallurgy, alloy steel piping components such as flanges, fittings, valves, and similar parts for use in pressure systems and high-temperature services. Compacts shall be manufactured by placing a single powder blend into a can,...

ASTM D381-25 - Standard Test Method for Gum Content in Fuels by Jet Evaporation
April 1, 2025 - ASTM International

5.1 The true significance of this test method for determining gum in motor gasoline is not firmly established. It has been proved that high gum can cause induction-system deposits and sticking of intake valves, and in most instances, it can be assumed that low gum will ensure absence of...

Advertisement