5.1 This test method is designed to aid in identifying types of coolants. While the ash is primarily due to the inorganic inhibitors used, it is not a measure of the total inhibitor concentration because of the loss of organic inhibitors. 5.2 An ash content greater than that stated in...
5.1 Inorganic constituents in water and wastewater must be identified and measured to support effective water quality monitoring and control programs. Currently, one of the simplest, most practical and cost effective means of accomplishing this is through the use of chemical test kits and...
1.1 This specification covers the basic requirements for a corrosion-resistant coating consisting of an inorganic aluminum particle-filled basecoat and an organic or inorganic topcoat, depending on the specific requirements. 1.2 The coating may be specified with basecoat only, or with...
1.1 This test method covers a direct injection ion chromatographic procedure for determining existent and potential inorganic sulfate and total inorganic chloride content in hydrous and anhydrous denatured ethanol and butanol to be used in motor fuel applications. It is intended for...
1.1 This practice covers the manner in which the various results of examination and analysis to determine the composition of deposits formed from water for subsurface injection are to be reported. 1.2 All analyses shall be made in accordance with the test methods of ASTM, unless otherwise specified...
1.1 This classification system provides a means for specifying or describing pertinent properties of commercial nonmetallic gasket materials. Materials composed of asbestos, cork, cellulose, and other organic or inorganic materials in combination with various binders or impregnants are...
4.1 The oxyhalides chlorite, chlorate, and bromate are inorganic disinfection by-products (DBPs) of considerable health risk concern worldwide. The occurrence of chlorite and chlorate is associated with the use of chlorine dioxide, as well as hypochlorite solutions used for drinking water...
1.1 These test methods describe procedures for assessing the adhesion of metallic and inorganic coatings and other thin films to metallic and nonmetallic substrates. Assessment is made by applying pressure-sensitive tape to a coated surface and then utilizing a mechanical device to remove...
5.1 This guide is designed to assist a practitioner in the selection of appropriate sample preparation methods for the analysis, comparison, and identification of pressure sensitive adhesive (PSA) tapes. 5.2 It is not the intent of this guide to present comprehensive theories and methods of IR...
5.1 This guide is designed to assist a practitioner in the selection of appropriate sample preparation methods for the analysis, comparison, and identification of pressure sensitive adhesive (PSA) tapes. 5.2 It is not the intent of this guide to present comprehensive theories and methods of IR...
5.1 Lubricants can contain basic constituents that are present as additives. The relative amount of these materials can be determined by titration with acids. The base number is a measurement of the amount of basic substances in the oil under the conditions of the testing procedure. 5.2 A primary...
5.1 This guide is designed to assist a practitioner in the selection of appropriate sample preparation methods for the analysis, comparison, and classification of paints. 5.2 It is not the intent of this guide to present comprehensive theories and methods of IR spectroscopy. It is necessary that...
1.1 This guide covers general considerations for the quality control (QC) practices for use with screening methods for organic and inorganic constituents in water. Methods are provided by various standard setting bodies, governmental agencies, as well as many domestic and international...
3.1 In accordance with Terminology D8178, recovered carbon black is defined as a semi-reinforcing filler derived from post-consumer rubber goods (feedstock) via a variety of thermal decomposition processes. This type of filler, predominantly consisting of carbon, also contains inorganic...
1.1 This test method covers a procedure for the determination of basic constituents in petroleum products and new and used lubricants. This test method resolves these constituents into groups having weak-base and strong-base ionization properties, provided the dissociation constants of the more...
5.1 A knowledge of water extractable inorganic halides in oil is important when deciding whether or not the oils need desalting. Excessive halide, especially in crude oil, frequently results in higher corrosion rates in refining units.
7.1 Ash content gives an estimate of the inorganic content of cellulose ester samples. The presence of high levels of inorganic content (ash) can be detrimental to the melt stability and optical clarity of a cellulose ester in melt processing or act as a potential source of insolubles...
5.1 This test method is intended for evaluating the cleanliness of fuels identified in the scope. 5.2 Detection of particles can indicate degradation of the fluid condition. Particles, whether organic or inorganic, can cause fouling of fuel filters and damage pumps, injectors, and pistons....
1.1 This test method covers the determination of basic constituents in petroleum products by titration with perchloric acid in glacial acetic acid. 1.2 Procedures A and B use different titration solvent volumes and sample weights. Note 1: A round robin on a series of new and used oils and additive...
Narrow Your Results