5.1 This guide is intended for use by ?eld personnel for the rapid evaluation of the presence of and type of radioactive materials, based on information obtained from available ?eld instrumentation. Guidance is offered for actions which may be taken to better understand the instrument...
1.1 This test method covers procedures for determining the bulk density of coal using instrumentation that measures the relative backscatter of nuclear gamma radiation throughout the depth of the stockpile under test. 1.2 This procedure is applicable to all ranks of coal. 1.3 The values...
1.1 This test method covers the determination of the surface area of advanced ceramic materials (in a solid form) based on multilayer physisorption of gas in accordance with the method of Brunauer, Emmett, and Teller (BET) (1) and based on IUPAC Recommendations (1984 and 1994) (2, 3). This test...
1.1 This test method describes the assessment of material thermal stability through the determination of the temperature at which the materials start to decompose or react and the extent of the mass change using thermogravimetry. The test method uses minimum quantities of material and is applicable...
1.1 This specification defines general specifications for heat meters. Heat meters are instruments that measure heat in heat exchange circuits in which energy is absorbed (cooling) or given up (heating) by a flowing liquid. 1.2 For this specification, the necessary elements of a heat meter consist...
1.1 This test method is used to establish the concentration of free cyanide in an aqueous wastewater, effluent and in-stream free cyanide concentrations after mixing treated water with receiving water. The test conditions of this test method are used to measure free cyanide (HCN and CN-) and...
1.1 This terminology pertains to the conversion of solar energy into other forms of energy by various means, including thermal absorption (i.e., solar thermal) and the photovoltaic effect (i.e., photovoltaics). 1.2 This terminology also pertains to instrumentation used to measure solar...
1.1 This test method covers the determination of fracture energy (Gf) of asphalt mixtures using the disk-shaped compact tension geometry. The disk-shaped compact tension geometry is a circular specimen with a single edge notch loaded in tension. The fracture energy can be utilized as a parameter to...
This practice provides guidelines for acoustic emission (AE) examination or monitoring of structures, such as pressure vessels, piping systems, or other structures that can be stressed by mechanical or thermal means. The basic functions of an AE monitoring system are to detect, locate, and classify...
1.1 This test method assesses metal or other ions released from single-use, metallic, implantable medical devices or components thereof by exposing the device to solutions simulating the in vivo environment and temperature in a container for a predetermined time frame with regular sampling at...
4.1 The recommended measurement procedures described in this guide are intended to provide performance-related measurements that can be reproduced under the specified test conditions using commercially available test instrumentation. These measurements indicate capabilities of sections of...
3.1 Acoustic emission data is affected by several characteristics of the instrumentation. The most obvious of these is the system sensitivity. Of all the parameters and components contributing to the sensitivity, the acoustic emission sensor is the one most subject to variation. This...
5.1 This test method provides guidelines and basic test methods for the accuracy verification of infrared thermometers. It includes test set-up and calculation of uncertainties. It is intended to provide the user with a consistent method, while remaining flexible in the choice of calibration...
4.1 Detection and location of AE sources in weldments during fabrication may provide information related to the integrity of the weld. Such information may be used to direct repair procedures on the weld or as a guide for application of other nondestructive evaluation (NDE) methods. A major...
5.1 The indirect tensile cracking test is used to determine asphalt mixture cracking resistance at an intermediate temperature which could range from 5?°C to 35?°C, depending on local climate. The specimens are readily obtained from Superpave gyratory compactor compacted cylinders with a diameter...
5.1 This practice allows for compositional analysis of the gases in equilibrium with crude oil, condensate, and liquid petroleum products at a 4:1 vapor/liquid ratio at ambient temperature for analysis using typical instrumentation (RGA) already available in typical refinery laboratories....
5.1 This practice provides information necessary to document the accuracy and performance of an acoustic emission system. This information is useful for reference purposes to assure that the instrumentation performance remains consistent with time and use, and provides the information needed...
Narrow Your Results