loading
ASTM D229-26 - Standard Test Methods for Rigid Sheet and Plate Materials Used for Electrical Insulation
June 1, 2026 - ASTM International

1.1 These test methods cover procedures for testing rigid electrical insulation normally manufactured in flat sheet or plate form. They are generally used as terminal boards, spacers, voltage barriers, and circuit boards. 1.2 Use Test Methods D619 (withdrawn) or Specification D710 for tests...

ASTM C1696-26 - Standard Guide for Industrial Thermal Insulation Systems
March 1, 2026 - ASTM International

1.1 This guide covers information on selection of insulation materials, systems design, application methods, protective coverings, guarantees, inspection, testing, and maintenance of thermal insulation primarily for industrial applications in a temperature range of -320 to 1200°F...

ASTM D1711-26 - Standard Terminology Relating to Electrical Insulation
June 1, 2026 - ASTM International

1.1 This terminology standard is a compilation of technical terms associated with testing and specifying solid electrical and electronic insulating materials. 1.2 This terminology standard shall contain all definitions that are balloted specifically through Subcommittee D09.94 and through D09 main...

ASTM E2231-26 - Standard Practice for Specimen Preparation and Mounting of Pipe and Duct Insulation Materials to Assess Surface Burning Characteristics
April 15, 2026 - ASTM International

1.1 This practice describes procedures for specimen preparation and mounting when testing pipe and duct insulation materials to assess flame spread and smoke development as surface burning characteristics using Test Method E84. 1.2 If the pipe or duct insulation materials to be tested...

ASTM C129-26 - Standard Specification for Dry-Cast Nonloadbearing Concrete Masonry Units
July 15, 2026 - ASTM International

1.1 This specification covers dry-cast hollow and solid nonloadbearing concrete masonry units machine-made from hydraulic cement, water, and suitable mineral aggregates with or without the inclusion of other materials. These units are intended for use in nonloadbearing partitions, but under certain...

ASTM C1484-10(2026) - Standard Specification for Vacuum Insulation Panels
March 1, 2026 - ASTM International

This specification covers the general requirements for vacuum insulation panels (VIP). These panels have been used wherever high thermal resistance is desired in confined space applications, such as transportation, equipment, and appliances. The panel barrier consists of one or more layers...

ASTM D5485-26 - Standard Test Method for Determining Corrosive Effect of Combustion Products Using the Cone Corrosimeter
June 1, 2026 - ASTM International

5.1 The metal loss from corrosion is directly related to the increase in electrical resistance of the target due to the decrease in conductive cross-sectional area. 5.2 The relationship between resistance increase of metallic targets used in this test method and the amount of metal loss as reported...

ASTM C421-26 - Standard Test Method for Tumbling Friability of Preformed Block-Type and Preformed Pipe-Covering-Type Thermal Insulation
April 1, 2026 - ASTM International

1.1 This test method covers determination of the mass loss of preformed block-type and preformed pipe-covering-type thermal insulation as a result of a combination of abrasion and impact produced by a laboratory tumbling mechanism. 1.2 The values stated in inch-pound units are to be regarded...

ASTM D7859-26 - Standard Practice for Spraying, Sampling, Packaging, and Test Specimen Preparation of Spray Polyurethane Foam (SPF) Insulation for Testing of Emissions Using Environmental Chambers
April 1, 2026 - ASTM International

5.1 Manufacturers of SPF insulation may need to test their products for vapor-phase emissions of volatile and semi-volatile organic compounds in order to comply with voluntary standards, purchase specifications, or other requirements. 5.2 Since SPF insulation is formed by chemical...

ASTM C1936-26 - Standard Test Method for Corrosiveness of Mineral-Fiber or Cellulosic-Fiber Insulation by Comparison to Control
March 1, 2026 - ASTM International

1.1 This method provides a qualitative measure of the corrosiveness of mineral-fiber or cellulose fiber insulation by comparison to a control. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of...

ASTM C534/C534M-26 - Standard Specification for Preformed Flexible Elastomeric Cellular Thermal Insulation in Sheet and Tubular Form
April 15, 2026 - ASTM International

This specification covers sheet and tubular preformed flexible elastomeric cellular thermal insulation. The materials are classified into three grades according to the operating temperature range of the industrial systems that each material is used for. The non-thermoplastic, thermoset...

ASTM D3874-26 - Standard Test Method for Ignition of Materials by Hot Wire Sources
June 1, 2026 - ASTM International

5.1 During operation of electrical equipment, including wires, resistors, and other conductors, it is possible for overheating to occur, under certain conditions of operation or when malfunctions occur. When this happens, a possible result is ignition of the insulation material. 5.2 This...

ASTM E1317-26a - Standard Test Method for Flammability of Surface Finishes
June 1, 2026 - ASTM International

5.1 This test method provides a means for evaluation of the flammable performance of surface finish materials. 5.2 A specimen of the surface finish of concern is mounted on the support material contemplated for use and subjected to a controlled significant radiant-flux exposure. 5.3 All specimens...

ASTM C1258-21a(2026) - Standard Test Method for Elevated Temperature and Humidity Resistance of Vapor Retarders for Insulation
March 1, 2026 - ASTM International

5.1 On systems operating at sub-ambient temperature, humid ambient conditions cause a vapor driving force toward the insulation. If not retarded, the driven moisture vapor is detrimental to the insulation's thermal resistance. A vapor retarder must resist degradation in order maintain its...

ASTM C929-14(2026) - Standard Practice for Handling, Transporting, Shipping, Storage, Receiving, and Application of Thermal Insulation Materials For Use in Contact with Austenitic Stainless Steel
March 1, 2026 - ASTM International

4.1 Insulations that are used as a part of the thermal insulation system in contact with austenitic stainless steels have the potential to become contaminated with water soluble corrosive ions which, in turn, if permitted to reach the stainless steel surface, are possible to...

ASTM D1000-26 - Standard Test Methods for Pressure-Sensitive Adhesive-Coated Tapes Used for Electrical and Electronic Applications
June 1, 2026 - ASTM International

1.1 These test methods cover procedures for testing pressure-sensitive adhesive-coated tapes to be used as electrical insulation. These tapes are classified as follows: 1.1.1 Class 1-Non-elastomeric backings made from materials such as: Paper, flat or creped, Fabric, uncoated or coated,...

ASTM C547-25 - Standard Specification for Mineral Fiber Pipe Insulation
December 1, 2025 - ASTM International

This specification covers mineral fiber pipe insulation that are formed into hollow cylinders for standard pipe and tubing sizes. The pipe insulation may be molded or precision v-grooved with one or more walls split longitudinally and used up to a specified temperature. The materials...

ASTM C1534-26 - Standard Specification for Flexible Polymeric Foam Sheet Insulation Used as a Thermal and Sound Absorbing Liner for Duct Systems
April 1, 2026 - ASTM International

This specification covers the composition, dimensions, and physical properties of flexible unfaced foam sheet, used to insulate interior surfaces of HVAC ducts, plenums and equipment used for the distribution of conditioned air. The flexible polymeric insulations of this specification are...

ASTM C1728-25a - Standard Specification for Flexible Aerogel Insulation
December 1, 2025 - ASTM International

This specification covers the classification and performance of flexible aerogel thermal insulation. It indicates the mechanical, chemical, and property requirements of the flexible aerogel insulation, such as its thickness, density, and flexibility. It also lists the performance...

ASTM E2568-17a(2026) - Standard Specification for PB Exterior Insulation and Finish Systems
January 1, 2026 - ASTM International

This specification covers PB Exterior Insulation and Finish Systems (EIFS) defined as an exterior, non-bearing wall covering providing a weather-resistant exterior wall envelope on walls required to be combustible or noncombustible, fireresistance-rated or nonfire-resistance-rated. Further,...

Advertisement