5.1 The modular bore and cone interfaces of total joint prostheses are subjected to loads that could result in micromotion and fretting corrosion at the bore and cone taper interface. Release of ionic and particulate products of fretting corrosion could result in increased wear of the...
1.1 This guide covers the manufacture of Weight Shift aircraft and their qualification for certification. 1.2 This guide applies to Weight Shift Control aircraft seeking civil aviation authority approval, in the form of flight certificates, flight permits, or other like documentation. 1.3 This...
1.1 This test method is used to measure the resistance of materials used in protective clothing to penetration by blood-borne pathogens using a surrogate microbe under conditions of continuous liquid contact. Protective clothing material pass/fail determinations are based on the detection of viral...
1.1 This specification covers the required release and retention characteristics of ski-binding-boot (S-B-B) systems. This specification is applicable to all recreational snow skiing bindings that have safety release mechanisms. Specifically, this performance standard establishes the minimum...
5.1 Photovoltaic modules and components must be resistant to prolonged exposure to solar radiation, moisture, and heat. Degradation of polymeric components, delamination at the encapsulant and other interfaces, and moisture ingress are among the degradation modes known to decrease the output...
1.1 This test method describes the determination of the Mode I dominant fracture toughness, GIc, associated with facesheet-to-core separation of sandwich constructions using the single cantilever beam (SCB) specimen. This separation can consist of a disbond of the facesheet-to-core interface...
4.1 This practice is a guideline for a short-term screening test for the evaluation of the tissue response to materials that may be selected for implantation in the human body and should be done in accordance with good laboratory practices. This test may be performed prior to long-term testing (for...
4.1 This guide provides information to assist engineers with the design requirements and construction guidelines for paving an open-graded friction course (OGFC) surface layer. An OGFC is primarily used to improve the skid resistance and wear resistance of an asphalt pavement by providing an escape...
4.1 Reliable dosimetry is indispensable for research on the effects of ionizing radiation on materials and products. Without reliable dosimetry valid conclusions cannot be reached, or the wrong conclusions might be reached. 4.2 This document is intended to provide direction on how to conduct...
5.1 These test methods are part of an overall suite of related test methods that provide repeatable measures of human-system interaction capability including robotic system mobility, dexterity, inspection, remote operator proficiency, and situational awareness. In particular, the operator control...
This specification covers international standards for the crew interface aspects of airworthiness and design for aircraft. The applicant for a design approval must seek the individual guidance of their respective civil aviation authority (CAA) body concerning the use of this specification as...
1.1 This practice covers software development, validation and verification practices for software that is part of an unmanned aircraft system (UAS), including its associated elements. It may also be used by third-party service providers, including UAS Traffic Management (UTM) service providers. 1.1...
1.1 This guide covers the categories of anchors and anchoring systems and discusses the design principles to be considered in selecting anchors or systems that will resist gravity loads and applied loads. 1.2 This guide sets forth basic requirements for the design of stone anchorage and provides a...
This specification covers the male and female threaded connectors used to interface a propellant source to a paintball marker. The male connector shall incorporate a means for propellant shutoff that shall meet the maximum leakage requirement. When the male and female connectors are joined...
5.1 The procedure described in this test method for determination of the shear resistance for the GCL or the GCL interface is intended as a performance test to provide the user with a set of design values for the test conditions examined. The test specimens and conditions, including normal...
This test method deals with static, dynamic, and wear testing of extra-discal motion preserving implants. These implants are intended to augment spinal stability without significant tissue removal while allowing motion of the functional spinal unit(s). Wear is assessed using a weight loss method...
This specification covers the general requirements for the Type IV Cargo Bed Cover (CBC). The Type IV Cargo Bed Cover is a removable general purpose rigid enclosure for the cargo bed of the M923, 5 Ton Cargo Truck/M1083, 5 Ton Medium Tactical Vehicle (MTV)/M1095, 5 Ton MTV Trailer. The CBC provides...
This specification covers international standards for the crew interface aspects of airworthiness and design for aircraft. The applicant for a design approval must seek the individual guidance of their respective civil aviation authority (CAA) body concerning the use of this specification as...