loading
ASTM F2191/F2191M-13(2025) - Standard Specification for Packing Material, Graphitic or Carbon Braided Yarn
October 1, 2025 - ASTM International

1.1 This specification covers staple or continuous filament carbon/graphite yarn valve stem compression packing, suitable for use as end-rings on packing systems for valves. Intended services include steam, hydrocarbons, water, and non-oxidizing chemicals. Where this specification is...

ASTM E1151-93(2026) - Standard Practice for Ion Chromatography Terms and Relationships
January 1, 2026 - ASTM International

1.1 This practice deals primarily with identifying the terms and relationships of those techniques that use ion exchange chromatography to separate mixtures and a conductivity detector to detect the separated components. However, most of the terms should also apply to ion chromatographic techniques...

ASTM C50/C50M-13(2025) - Standard Practice for Sampling, Sample Preparation, Packaging, and Marking of Lime and Limestone Products
December 1, 2025 - ASTM International

1.1 This practice covers procedures for the collection and reduction of samples of lime and limestone products to be used for physical and chemical tests. 1.2 This practice further covers inspection, rejection, retesting, packing, and marking of lime and limestone products as it may be used...

ASTM C136/C136M-25 - Standard Test Method for Sieve Analysis of Fine and Coarse Aggregates
November 1, 2025 - ASTM International

1.1 This test method covers the determination of the particle size distribution of fine and coarse aggregates by sieving. 1.2 Some specifications for aggregates which reference this test method contain grading requirements including both coarse and fine fractions. Instructions are included for...

ASTM E1582-25 - Standard Test Method for Temperature Calibration of Thermogravimetric Analyzers
September 1, 2025 - ASTM International

1.1 This test method describes the temperature calibration of thermogravimetric analyzers over the temperature range from 25 °C to 1500 °C and is applicable to commercial and custom-built apparatus. This calibration may be accomplished by the use of either melting point standards or magnetic...

ASTM F2602-18(2025) - Standard Test Method for Determining the Molar Mass of Chitosan and Chitosan Salts by Size Exclusion Chromatography with Multi-angle Light Scattering Detection (SEC-MALS)
October 1, 2025 - ASTM International

1.1 This test method covers the determination of the molar mass of chitosan and chitosan salts intended for use in biomedical and pharmaceutical applications as well as in tissue-engineered medical products (TEMPs) by size exclusion chromatography with multi-angle laser light scattering detection...

ASTM D6179-20(2025) - Standard Test Methods for Rough Handling of Unitized Loads and Large Shipping Cases and Crates
August 1, 2025 - ASTM International

1.1 These test methods cover testing the integrity of unitized loads and large shipping cases and crates as well as the ability of the contents to endure rough handling. Not all of the test methods are applicable to all products, containers, and loads. These test methods are applicable to common...

ASTM D4441-20(2025) - Standard Specification for Aqueous Dispersions of Polytetrafluoroethylene
July 1, 2025 - ASTM International

1.1 This specification covers aqueous dispersions of polytetrafluoroethylene (PTFE) resins. These resins are homopolymers of tetrafluoroethylene, or in some cases modified homopolymers containing not more than 1?% by weight of other fluoromonomers. 1.1.1 The dispersion is usually stabilized by one...

ASTM D4404-25 - Standard Test Method for Determination of Pore Volume and Pore Volume Distribution of Soil and Rock by Mercury Intrusion Porosimetry
May 15, 2025 - ASTM International

1.1 This test method covers the determination of the pore volume and the pore volume distributions of soil and rock by the mercury intrusion porosimetry method. The range of apparent diameters of pores for which this test method is applicable is fixed by the operating pressure range of the testing...

ASTM D4781-24 - Standard Test Method for Mechanically Tapped Packing Density of Fine Catalyst Particles and Catalyst Carrier Particles
September 1, 2024 - ASTM International

1.1 This test method covers the determination of the mechanically tapped packing density of fine catalyst and catalyst carrier particles smaller than 0.8 mm in diameter. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this...

ASTM D4164-24 - Standard Test Method for Mechanically Tapped Packing Density of Formed Catalyst and Catalyst Carriers
September 1, 2024 - ASTM International

5.1 This test method is to be used for measuring the mechanically tapped packing density of formed particles that will not break up during sampling, filling, or tapping of the measuring cylinder under test conditions.

ASTM G147-24 - Standard Practice for Conditioning and Handling of Materials for Natural and Artificial Weathering Tests
December 1, 2024 - ASTM International

1.1 This practice covers specimen identification, packing, shipping, handling, and conditioning before, during, and after natural and artificial weathering testing. 1.2 This practice includes details on the conditioning of specimens after exposure and before examination. This practice also...

JIS INTERNATIONAL STD - JIS International Standardization Handbook
January 1, 2019 - JSA
A description is not available for this item.
ASTM D5639/D5639M-25 - Standard Practice for Selection of Corrugated Fiberboard Materials and Box Construction Based on Performance Requirements
January 1, 2025 - ASTM International

4.1 This practice assists users in selecting appropriate performance characteristics of corrugated fiberboard or box construction, or both, commensurate with their user's needs for packing and distribution of goods. This practice describes several attributes of fiberboard and boxes which...

ASTM F2087-13(2024) - Standard Specification for Packing, Fiberglass, Braided, Rope, and Wick
June 1, 2024 - ASTM International

1.1 This specification covers the general requirements and tests for braided, rope, and wick fiberglass packing used for boiler, furnace, and other high-temperature equipment seals for service temperatures up to 1000?°F (538?°C). 1.2 The values stated in inch-pound units are to be regarded...

Advertisement