loading
API OIL WELL CEMENT - OIL-WELL CEMENTING PRACTICES IN THE UNITED STATES
January 1, 1959 - API

FOREWORD: Each year in the United States several thousand wells are drilled and completed - some productive of oil or gas and some dry - and during this drilling and completion most of these wells are cased, with the casing set in the bore hole surrounded by oil-well cement. This book...

SWRI SEALANTS - SEALANTS: THE PROFESSIONALS' GUIDE
SWRI
A description is not available for this item.
ASTM D8236-26 - Standard Practice for Preparing an Equilibrium Liquid/Vapor Sample of Live Crude Oil, Condensates, or Liquid Petroleum Products Using a Manual Piston Cylinder for Subsequent Liquid Analysis or Gas Analysis
May 1, 2026 - ASTM International

5.1 This practice allows for compositional analysis of the gases in equilibrium with crude oil, condensate, and liquid petroleum products at a 4:1 vapor/liquid ratio at ambient temperature for analysis using typical instrumentation (RGA) already available in typical refinery laboratories....

ASTM D8112-26 - Standard Guide for Sampling, In-Service Lubricating Oils and Hydraulic Fluids in Industrial Applications
May 1, 2026 - ASTM International

5.1 Analyzing in-service lubricating oil and hydraulic fluid samples is crucial for assessing the condition of both the fluid and the equipment. The results of the fluid analysis guide the planning of any necessary corrective maintenance activities. 5.2 The objective of this guide is to...

ASTM D7919-26 - Standard Guide for Filter Debris Analysis (FDA) Using Manual or Automated Processes
June 1, 2026 - ASTM International

5.1 This guide is intended to provide machinery maintenance and monitoring personnel with a guideline for performing filter debris analysis as a means to determine machine condition. Correlating the filter contaminants to 'normal' and 'abnormal' lube system operation provides early indication of a...

ASTM C564-26 - Standard Specification for Rubber Gaskets for Cast Iron Soil Pipe and Fittings
February 1, 2026 - ASTM International

1.1 This specification covers preformed rubber gaskets used to seal joints in cast iron soil pipe and fittings. 1.2 The committee with jurisdiction over this standard is not aware of another comparable standard for materials covered in this standard. 1.3 The values stated in inch-pound units...

ASTM D7216-25 - Standard Test Method for Determining Automotive Engine Oil Compatibility with Typical Seal Elastomers
July 1, 2025 - ASTM International

5.1 Some engine oil formulations have been shown to lack compatibility with certain elastomers used for seals in automotive engines. These deleterious effects on the elastomer are greatest with new engine oils (that is, oils that have not been exposed to an engine's operating...

ASTM D7876-26 - Standard Practice for Practice for Sample Decomposition Using Microwave Heating (With or Without Prior Ashing) for Atomic Spectroscopic Elemental Determination in Petroleum Products and Lubricants
March 1, 2026 - ASTM International

1.1 This practice covers the procedure for use of microwave radiation for sample decomposition prior to elemental determination by atomic spectroscopy. 1.1.1 Although this practice is based on the use of inductively coupled plasma atomic emission spectrometry (ICP-AES) and atomic absorption...

ASTM D2628-25 - Standard Specification for Preformed Polychloroprene Elastomeric Joint Seals for Concrete Pavements
November 1, 2025 - ASTM International

This specification covers the material requirements for preformed polychloroprene elastomeric joint seals for concrete pavements. The seal consists of a multiple web design and is installed with a lubricant. The seal functions by compression of the seal between the faces...

ASTM D5704-25a - Standard Test Method for Evaluation of the Thermal and Oxidative Stability of Lubricating Oils Used for Manual Transmissions and Final Drive Axles
November 1, 2025 - ASTM International

1.1 This test method is commonly referred to as the L-60-1 test.2 It covers the oil-thickening, insolubles-formation, and deposit-formation characteristics of automotive manual transmission and final drive axle lubricating oils when subjected to high-temperature oxidizing conditions. 1.2 The...

ASTM D5704-25 - Standard Test Method for Evaluation of the Thermal and Oxidative Stability of Lubricating Oils Used for Manual Transmissions and Final Drive Axles
October 1, 2025 - ASTM International

1.1 This test method is commonly referred to as the L-60-1 test.2 It covers the oil-thickening, insolubles-formation, and deposit-formation characteristics of automotive manual transmission and final drive axle lubricating oils when subjected to high-temperature oxidizing conditions. 1.2 The...

ASTM E1234-12(2025) - Standard Practice for Handling, Transporting, and Installing Nonvolatile Residue (NVR) Sample Plates Used in Environmentally Controlled Areas for Spacecraft
September 1, 2025 - ASTM International

1.1 This practice covers the handling, transporting, and installing of sample plates used for the gravimetric determination of nonvolatile residue (NVR) within and between facilities. 1.2 The values stated in SI units are to be regarded as the standard. 1.3 This standard does not purport to address...

ASTM D6709-25 - Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence VIII Spark-Ignition Engine (CLR Oil Test Engine)
April 1, 2025 - ASTM International

5.1 This test method is used to evaluate automotive engine oils for protection of engines against bearing weight loss. 5.2 This test method is also used to evaluate the SIG capabilities of multiviscosity-graded oils. 5.3 Correlation of test results with those obtained in automotive service has not...

ASTM D5973-97(2025) - Standard Specification for Elastomeric Strip Seals with Steel Locking Edge Rails Used in Expansion Joint Sealing
May 1, 2025 - ASTM International

1.1 This specification covers the material requirements for preformed elastomeric strip seals and the corresponding steel locking edge rail used in expansion joint sealing. The scope of this specification is limited to preformed non-reinforced strip seals that mechanically lock into...

ASTM G182-25 - Standard Test Method for Determination of the Breakaway Friction Characteristics of Rolling Element Bearings
April 1, 2025 - ASTM International

1.1 This test method is an extension of Test Method G164 and uses an inclined plane and a paperclip rider to detect the presence or absence of lubricants on the surfaces of flexible webs. A study to identify free spinning or low rolling friction bearings indicated that the paperclip friction test...

Advertisement