loading
ASTM E979-25 - Standard Practice for Evaluation of Antimicrobial Agents as Preservatives for Invert Emulsion and Other Water Containing Hydraulic Fluids
July 1, 2025 - ASTM International

1.1 This laboratory practice is designed to evaluate the utility and effectiveness of antimicrobial agents intended to control microbial growth in invert emulsions and other water containing hydraulic fluids. Note 1: Procedures for preparation of water soluble hydraulic fluids and recovery...

ASTM E2527-15(2025) - Standard Test Method for Electrical Performance of Concentrator Terrestrial Photovoltaic Modules and Systems Under Natural Sunlight
June 1, 2025 - ASTM International

5.1 It is the intent of this test method to provide a recognized procedure for testing and reporting the electrical performance of a photovoltaic concentrator module or system. 5.2 If an inverter is used as part of the system, this test method can provide a dc or ac rating, or both. The dc...

ASTM D6431-25 - Standard Guide for Using the Direct Current Resistivity Method for Geophysical Site Investigation
July 1, 2025 - ASTM International

5.1 Concepts-The resistivity technique is used to measure the resistivity of subsurface materials. Although the resistivity of materials can be a good indicator of the type of subsurface material present, it is not a unique indicator. While the resistivity method is used to measure the resistivity...

ASTM B864/B864M-25 - Standard Specification for Corrugated Aluminum Box Culverts
May 1, 2025 - ASTM International

This specification covers the requirements for material, geometric, and wall section properties of aluminum box culverts manufactured from corrugated plate or sheet with attached rib stiffeners, for field assembly. Suitable fasteners and optional materials such as aluminum invert plates and...

ASTM E3482-25 - Standard Guide for Characterization of Encapsulation, Extraction, and Analysis of RNA in Lipid Nanoparticle Formulations for Drug Delivery
April 15, 2025 - ASTM International

1.1 Lipid nanoparticles (LNPs) have emerged as an important nanoscale drug delivery technology for the in vivo intracellular delivery of therapeutic proteins and nucleic acids. The safe and efficient delivery of therapeutic proteins and nucleic acids to cells and tissues can enable the effective...

ASTM F1216-24a - Standard Practice for Rehabilitation of Existing Pipelines and Conduits by the Inversion and Curing of a Resin-Impregnated Tube
November 1, 2024 - ASTM International

1.1 This practice describes the procedures for the reconstruction of pipelines and conduits (2?in. to 108?in. diameter) by the installation of a resin-impregnated, flexible tube which is inverted into the existing conduit by use of a hydrostatic head or air pressure. The resin is cured by...

ASTM D5094/D5094M-24 - Standard Test Methods for Gross Leakage of Liquids from Containers with Threaded or Lug-Style Closures
November 1, 2024 - ASTM International

5.1 These test methods are qualitative and used to indicate the integrity of the container and closure system in the distribution environment. 5.2 These test methods measure the ability of the container and closure system to prevent leakage when stored or transported upright, inverted, or on...

ASTM F1216-24 - Standard Practice for Rehabilitation of Existing Pipelines and Conduits by the Inversion and Curing of a Resin-Impregnated Tube
July 1, 2024 - ASTM International

4.1 This practice is for use by designers and specifiers, regulatory agencies, owners, and inspection organizations who are involved in the rehabilitation of conduits through the use of a resin-impregnated tube inverted through the existing conduit. As for any practice, modifications may be...

ASTM F3338-24 - Standard Specification for Design of Electric Engines for General Aviation Aircraft
September 15, 2024 - ASTM International

1.1 This specification covers minimum requirements for the design of electric engines. 1.2 Distributed propulsion is not excluded; however, additional requirements will be needed to address the additional issues that distributed propulsion can create. Some of those issues may include: use of a...

J2847/3_202311 - Communication for Plug-in Vehicles as a Distributed Energy Source
November 6, 2023 - SAE International

This SAE Recommended Practice applies to a plug-in electric vehicle (PEV) which is equipped with an onboard inverter and communicates using IEEE 2030.5-2018. It is a supplement to the SEP2 standard, which supports the use cases defined by SAE J2836/3. It provides guidance for the use of the...

UL 9741 - Electric Vehicle Power Export Equipment (EVPE)
September 29, 2023 - ULSE

1.1 The requirements of this standard apply to off-board unidirectional and bidirectional equipment rated 1000 Vac and 1500 Vdc or less, that transfers electrical energy between an electric vehicle and off board loads as well as operating in parallel with an electric power system, such as the...

ASTM C1920-23 - Standard Practice for Cleaning of Vitrified Clay Sanitary Sewer Pipelines
October 1, 2023 - ASTM International

4.1 Hydraulic cleaning methods include equipment that uses water and water velocity to clean the invert and walls of the vitrified clay sewer pipe. 4.2 The practice of high-velocity sewer cleaning is best described as a hydraulic cleaning method that uses water pressure to remove...

ASTM D8173-23 - Standard Guide for Site Preparation, Layout, Installation, and Hydration of Geosynthetic Cementitious Composite Mats
July 15, 2023 - ASTM International

4.1 This guide identifies proper layout, installation, and hydration procedures along with equipment for use by GCCM designers, inspectors, and installers. 4.2 Applications-Typical GCCM applications may include but are not limited to: 4.2.1 Hydraulic structure armoring or protection, including but...

ASTM F3220-17(2023) - Standard Practice for Prioritizing Sewer Pipe Cleaning Operations by Using Transmissive Acoustic Inspection
September 1, 2023 - ASTM International

4.1 Significance: 4.1.1 Collection system maintenance requires allocating cleaning resources to the right place prior to system failure (sanitary sewer overflows, mainline blockages, and building backups). Transmissive acoustic inspection provides a tool to assist in allocating cleaning resources...

ASTM E2848-13(2023) - Standard Test Method for Reporting Photovoltaic Non-Concentrator System Performance
August 1, 2023 - ASTM International

5.1 Because there are a number of choices in this test method that depend on different applications and system configurations, it is the responsibility of the user of this test method to specify the details and protocol of an individual system power measurement prior to the beginning of a...

ASTM F2207-06(2023) - Standard Specification for Cured-in-Place Pipe Lining System for Rehabilitation of Metallic Gas Pipe
July 1, 2023 - ASTM International

1.1 This specification covers requirements and method of testing for materials, dimensions, hydrostatic burst strength, chemical resistance, adhesion strength and tensile strength properties for cured-in-place (CIP) pipe liners installed into existing metallic gas pipes, 3/4 to 48 in. nominal pipe...

ASTM A964/A964M-23 - Standard Specification for Corrugated Steel Box Culverts
April 1, 2023 - ASTM International

This specification covers standard requirements for material, geometric, and wall section properties of steel box culverts manufactured from corrugated plate or sheet, with or without attached stiffeners, for field assembly. Appropriate fasteners and optional materials such as steel invert...

ASTM F1216-22 - Standard Practice for Rehabilitation of Existing Pipelines and Conduits by the Inversion and Curing of a Resin-Impregnated Tube
August 15, 2022 - ASTM International

4.1 This practice is for use by designers and specifiers, regulatory agencies, owners, and inspection organizations who are involved in the rehabilitation of conduits through the use of a resin-impregnated tube inverted through the existing conduit. As for any practice, modifications may be...

ASTM F3618-22 - Standard Practice for Cleaning of Thermoplastic Solid Wall Sanitary Sewer Pipelines
November 1, 2022 - ASTM International

4.1 Hydraulic cleaning methods include equipment that uses water and water velocity to clean the invert and walls of Thermoplastic Sewer Pipe. 4.2 The practice of high-velocity sewer cleaning is best described as a hydraulic cleaning method that uses water pressure to remove obstructions and...

UL 61730-1 - Photovoltaic (PV) Module Safety Qualification - Part 1: Requirements for Construction
October 28, 2022 - ULSE

This part of IEC 61730 specifies and describes the fundamental construction requirements for photovoltaic (PV) modules in order to provide safe electrical and mechanical operation. Specific topics are provided to assess the prevention of electrical shock, fire hazards, and personal injury due to...

Advertisement