1.1 This terminology covers those terms recommended by the International Union of Pure and Applied Chemistry (IUPAC), and is intended to provide guidance in the use of ion-selective electrodes for analytical measurement of species in water, wastewater, and brines. 1.2 This international...
5.1 Components of implanted medical devices can release ions, which may lead to adverse biological effects if released in sufficient quantities. Therefore, it may be necessary to characterize the ion release behavior over time to verify that a medical device or device components or...
1.1 These multi-test methods cover the determination of the oxyhalides-chlorite,
5.1 The ability of a fuel to dissipate charge that has been generated during pumping and filtering operations is controlled by its electrical conductivity, which depends upon its content of ion species. If the conductivity is sufficiently high, charges dissipate fast enough to prevent their...
5.1 This test method is used for measuring ammonia and ammonium ion in water samples and soil or plant extracts. 5.2 Ammonia compounds are widely distributed in the environment and may be applied as fertilizer, used as cleaning compounds, or used in water treatment. 5.3 Ammonia nitrogen...
This specification covers the requirements for 1,1,1,2,3,3,3-Heptaf
1.1 This test method covers the liquid chromatography tandem mass spectrometry (LC-MS/MS) detection and quantitation of N-nitrosamines after direct injection. It has been validated for groundwater, surface water, wastewater influents, and wastewater effluents. This test method is not limited to...
This practice deals primarily with identifying the terms and relationships of those techniques that use ion exchange chromatography to separate mixtures and a conductivity detector to detect the separated components. However, most of the terms should also apply to ion chromatographic...
1.1 These test methods cover procedures for the chemical and mass spectrometric analysis of nuclear-grade gadolinium oxide powders to determine compliance with specifications. 1.2 The analytical procedures appear in the following order: Sections Carbon by Direct Combustion-Thermal Conductivity...
1.1 This test method is used to establish the concentration of free cyanide in an aqueous wastewater, effluent and in-stream free cyanide concentrations after mixing treated water with receiving water. The test conditions of this test method are used to measure free cyanide (HCN and CN-) and...
1.1 This guide covers the identification and quantitation of organic compounds by gas chromatography/mass spectrometry (GC-MS) (electron impact) that are present or extracted from water and are capable of passing through a gas chromatograph without alteration. This guide can be used to provide...
1.1 This test method covers the identification and simultaneous measurement of purgeable volatile organic compounds. It has been validated for treated drinking water, wastewater, and ground water. This test method is not limited to these particular aqueous matrices; however, the applicability of...
1.1 This practice covers the calculation of supersaturation of barium sulfate, strontium sulfate, and calcium sulfate dihydrate (gypsum) in brackish water, seawater, and brines in which barium, strontium, and calcium ions either coexist or exist individually in solution in the presence of...
1.1 These test methods cover the determination of the operating ion-exchange capacity of both powdered cation-exchange resins (hydrogen form) and powdered anion-exchange resins (hydroxide form). These test methods are intended for use in testing new powdered ion-exchange resins when...
5.1 This test method can be used to evaluate the performance of unused mixed bed ion exchange cartridges for conformance to specifications. 5.2 This test method provides for the calculation of capacity in terms of the volume of water treated to a conductivity end point. 5.3 The test method...
5.1 The capability of this test method to collect and quantitate both particulate and gaseous fluorides over the ranges normally encountered in industrial atmospheres makes it applicable for industrial hygiene evaluation and control purposes. The recommended range of this test method for fluoride...
5.1 The presence of water extractables in ion-exchange resins can cause fouling of other materials downstream and contamination of process water. The quantity of water extractables is sometimes used as a specification to indicate resin quality, and typical values are 0.01?% to 0.1?%. 5.2 It...
1.1 This test method covers a direct injection ion chromatographic procedure for determining existent and potential inorganic sulfate and total inorganic chloride content in hydrous and anhydrous denatured ethanol and butanol to be used in motor fuel applications. It is intended for the...
1.1 This specification covers the requirements for chemically strengthened glass products that are used in general building construction, transportation, solar energy, and other electronic applications, such as PC screens, notebooks, tablets, smart phones, and e-readers, as well as copy machine...
1.1 This practice provides recommended procedures for sampling synthetic turf fiber and finished fabric in a manufacturing location for further testing to identify and quantify per- and polyfluoroalkyl substances (collectively hereafter referred to as PFAS) in synthetic turf fiber and fabric. 1.2...
Narrow Your Results