loading
ASTM E2969-18(2026) - Standard Test Methods for Transverse Load Tests on Panels Used in Wall Construction
April 1, 2026 - ASTM International

1.1 These test methods cover transverse load testing to determine the structural properties of wall segments. 1.2 These test methods serve to evaluate the performance of wall panels subject to transverse bending loads applied perpendicular to the plane of the wall. The tests are conducted on...

ASTM D8633-26 - Standard Test Methods for Evaluating the Cross-Grain Compression Strength and Stiffness of Wood and Wood-Based Products
April 1, 2026 - ASTM International

1.1 These test methods cover standardized procedures for evaluating the cross-grain compression strength and stiffness of wood and wood-based products. 1.2 Two types of test methods are provided: fundamental and application methods. 1.2.1 Fundamental Test Methods-These test methods characterize the...

ASTM A1003/A1003M-25 - Standard Specification for Steel Sheet, Carbon, Metallic- and Nonmetallic-Coated for Cold-Formed Framing Members
December 1, 2025 - ASTM International

1.1 This specification covers coated steel sheet used in the manufacture of cold-formed framing members, such as, but not limited to, studs, joists, purlins, girts, and track. 1.2 The steel sheet used for cold-formed framing members includes metallic-coated, painted metallic-coated, or...

ASTM E2179-25 - Standard Test Method for Laboratory Measurement of the Effectiveness of Floor Coverings in Reducing Impact Sound Transmission Through Concrete Floors
October 15, 2025 - ASTM International

5.1 The impact sound rating for a floor assembly is determined both by the basic floor assembly and the floor covering on the upper surface. The same floor covering in combination with different basic floor assemblies will not always give the same impact insulation class (IIC) and high-frequency...

ASTM D7746-21(2025) - Standard Practice for ?Calculating the Superimposed Load on Wood-frame Floor-Ceiling Assemblies for Standard Fire-Resistance Tests
August 1, 2025 - ASTM International

4.1 Test Methods E119, E1529, and other standard fire resistance test methods specify that throughout the fire-resistance test, a constant superimposed load shall be applied to a load-bearing test specimen to simulate a maximum allowable load condition. This superimposed load shall be the maximum...

ASTM E970-25 - Standard Test Method for Critical Radiant Flux of Exposed Attic Floor Insulation Using a Radiant Heat Energy Source
July 1, 2025 - ASTM International

5.1 This fire-test-response standard is designed to provide a basis for estimating one aspect of the fire exposure behavior to exposed insulation installed on the floors of building attics. The test environment is intended to simulate conditions that have been observed and defined in full-scale...

ASTM C739-25 - Standard Specification for Cellulosic Fiber Loose-Fill Thermal Insulation
April 15, 2025 - ASTM International

This specification covers the composition and physical requirements of chemically treated, recycled cellulosic fiber loose-fill type thermal insulation for installation in attics or enclosed spaces in housing and other buildings by pneumatic or pouring method. While the products are used in various...

ASTM D245-25 - Standard Practice for Establishing Structural Grades and Related Allowable Properties for Visually Graded Lumber
May 15, 2025 - ASTM International

3.1 Need for Lumber Grading: 3.1.1 Individual pieces of lumber, as they come from the saw, represent a wide range in quality and appearance with respect to freedom from knots, cross grain, shakes, and other characteristics. Such random pieces likewise represent a wide range in strength, utility,...

ASTM E3258-25 - Standard Guide for Evaluation of Changes to the Thermal, Moisture and Ventilation Performance of Existing Roof Enclosures (with Vented or Sealed Attic or Rafter Spaces)
March 1, 2025 - ASTM International

1.1 This guide covers the evaluation of hygrothermal impacts to existing roof enclosures resulting from roof enclosure alterations or changes to the interior environment. Examples of alterations that may affect the hygrothermal performance include but may not be limited to: installation of or...

ASTM D5055-24 - Standard Specification for Establishing and Monitoring Structural Capacities of Prefabricated Wood I-Joists
December 1, 2024 - ASTM International

This specification gives procedures for establishing, monitoring, and reevaluating structural capacities of prefabricated wood I-joists. Capacities considered are shear, moment, and stiffness. Procedures for establishing common details are given and certain design considerations specific to...

ASTM D7672-24 - Standard Specification for Evaluating Structural Capacities of Rim Board Products and Assemblies
February 1, 2024 - ASTM International

1.1 This specification provides procedures for testing and establishing the structural capacities of proprietary rim board products and assemblies for use in light-frame wood construction using I-joist or structural composite lumber joist framing. This specification does not apply to...

ASTM C739-24 - Standard Specification for Cellulosic Fiber Loose-Fill Thermal Insulation
March 1, 2024 - ASTM International

This specification covers the composition and physical requirements of chemically treated, recycled cellulosic fiber loose-fill type thermal insulation for installation in attics or enclosed spaces in housing and other buildings by pneumatic or pouring method. While the products are used in various...

ASTM D6109-24 - Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastic Lumber and Related Products
February 1, 2024 - ASTM International

1.1 These test methods are suitable for determining the flexural properties for any solid or hollow manufactured plastic lumber product of square, rectangular, round, or other geometric cross section that shows viscoelastic behavior. The test specimens are whole "as manufactured" pieces without any...

ASTM E970-23 - Standard Test Method for Critical Radiant Flux of Exposed Attic Floor Insulation Using a Radiant Heat Energy Source
October 1, 2023 - ASTM International

5.1 This fire-test-response standard is designed to provide a basis for estimating one aspect of the fire exposure behavior to exposed insulation installed on the floors of building attics. The test environment is intended to simulate conditions that have been observed and defined in full-scale...

ASTM C1373/C1373M-23 - Standard Practice for Determination of Thermal Resistance of Attic Insulation Systems Under Simulated Winter Conditions
September 1, 2023 - ASTM International

1.1 This practice presents a laboratory procedure to determine the thermal resistance of attic insulation systems under simulated steady-state winter conditions. The practice applies only to attic insulation systems that face an open attic air space. 1.2 The thermal resistance of the insulation is...

ASTM A1003/A1003M-23 - Standard Specification for Steel Sheet, Carbon, Metallic- and Nonmetallic-Coated for Cold-Formed Framing Members
June 15, 2023 - ASTM International

1.1 This specification covers coated steel sheet used in the manufacture of cold-formed framing members, such as, but not limited to, studs, joists, purlins, girts, and track. 1.2 The steel sheet used for cold-formed framing members includes metallic-coated, painted metallic-coated, or...

ASTM A1003/A1003M-23e1 - Standard Specification for Steel Sheet, Carbon, Metallic- and Nonmetallic-Coated for Cold-Formed Framing Members
June 15, 2023 - ASTM International

1.1 This specification covers coated steel sheet used in the manufacture of cold-formed framing members, such as, but not limited to, studs, joists, purlins, girts, and track. 1.2 The steel sheet used for cold-formed framing members includes metallic-coated, painted metallic-coated, or...

ASTM D7568-23 - Standard Specification for Polyethylene-Based Structural-Grade Plastic Lumber for Outdoor Applications
February 1, 2023 - ASTM International

1.1 This specification covers a type of plastic lumber product, defined as polyethylene-based structural-grade plastic lumber (SGPL), for use as main framing members, including joists, stringers, beams, columns; and secondary framing members, including planking, posts and bracing; in outdoor...

ASTM D6874-22a - Standard Test Methods for Nondestructive Evaluation of the Stiffness of Wood and Wood-Based Materials Using Transverse Vibration or Stress Wave Propagation
October 1, 2022 - ASTM International

1.1 These test methods cover the non-destructive determination of the following dynamic properties of wood and wood-based materials from measuring the fundamental frequency of vibration: 1.1.1 Flexural (see Refs (1-3))2 stiffness and apparent modulus of elasticity (Etv) properties using simply or...

ASTM E2322-22 - Standard Test Method for Conducting Transverse and Concentrated Load Tests on Panels used in Floor and Roof Construction
October 1, 2022 - ASTM International

1.1 This test method covers the following procedures for determining the structural properties of segments of floor and roof constructions: Section Test Specimens 5 Loading 6 Deformation Measurements 7 Report 8 Precision and Bias 9 ?Testing Floors Transverse Load 10 Concentrated Load 11 ?Testing...

Advertisement