loading
SSPC AMBIENT CONDITIONS - MONITORING AND CONTROLLING AMBIENT CONDITIONS DURING COATING OPERATIONS
November 1, 2004 - SSPC

Introduction The locally prevailing air temperature, the moisture content in the air (% relative humidity), and the temperature at which moisture will condense on surfaces (dew point) are commonly called the ambient conditions. If these conditions are not within the ranges required by a...

MPIF LIQUID SINTERING - LIQUID PHASE SINTERING
MPIF
A description is not available for this item.
AIHA NOISE & HEARING - THE NOISE MANUAL
AIHA
A description is not available for this item.
NOISE-VIBRATION PROBLEM - NOISE-VIBRATION PROBLEM-SOLUTION WORKBOOK
AIHA
A description is not available for this item.
ASTM D8236-26 - Standard Practice for Preparing an Equilibrium Liquid/Vapor Sample of Live Crude Oil, Condensates, or Liquid Petroleum Products Using a Manual Piston Cylinder for Subsequent Liquid Analysis or Gas Analysis
May 1, 2026 - ASTM International

5.1 This practice allows for compositional analysis of the gases in equilibrium with crude oil, condensate, and liquid petroleum products at a 4:1 vapor/liquid ratio at ambient temperature for analysis using typical instrumentation (RGA) already available in typical refinery...

ASTM E1419/E1419M-26 - Standard Practice for Examination of Seamless, Gas-Filled, Pressure Vessels Using Acoustic Emission
May 1, 2026 - ASTM International

1.1 This practice provides guidelines for acoustic emission (AE) examinations of seamless pressure vessels (tubes) of the type used for distribution or storage of industrial gases. 1.2 This practice requires pressurization to a level greater than normal use. Pressurization medium may be gas...

ASTM E2677-26 - Standard Test Method for Estimating Limits of Detection in Trace Detectors for Explosives and Drugs of Interest
March 1, 2026 - ASTM International

1.1 In harmony with the Joint Committee for Guides in Metrology (JCGM) and detection concepts of the International Union of Pure and Applied Chemistry (IUPAC) (1, 2), this test method uses a series of replicated measurements of an analyte at dosage levels giving instrumental responses that...

ASTM D2622-26 - Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry
March 1, 2026 - ASTM International

1.1 This test method covers the determination of total sulfur in petroleum and petroleum products that are single-phase and either liquid at ambient conditions, liquefiable with moderate heat, or soluble in hydrocarbon solvents. These materials can include diesel fuel, jet fuel,...

ASTM D5146-10(2026) - Standard Guide to Testing Solvent-Borne Architectural Coatings
March 1, 2026 - ASTM International

This guide covers the selection and use of procedures for testing solvent-borne architectural coatings to be used on exterior, interior, or both types of surfaces. The properties that can be examined by the test methods listed herein are as follows: liquid paint properties (skinning,...

ASTM G86-17(2025) - Standard Test Method for Determining Ignition Sensitivity of Materials to Mechanical Impact in Ambient Liquid Oxygen and Pressurized Liquid and Gaseous Oxygen Environments
July 1, 2025 - ASTM International

5.1 This test method evaluates the relative sensitivity of materials to mechanical impact in ambient pressure liquid oxygen, pressurized liquid oxygen, and pressurized gaseous oxygen. 5.2 Any change or variation in test sample configuration, thickness, preparation, or...

ASTM E1930/E1930M-25 - Standard Practice for Examination of Liquid-Filled Atmospheric and Low-Pressure Metal Storage Tanks Using Acoustic Emission
September 1, 2025 - ASTM International

1.1 This practice covers guidelines for acoustic emission (AE) examinations of new and in-service aboveground storage tanks of the type used for storage of liquids. 1.2 This practice will detect acoustic emission in areas of sensor coverage that are stressed during the course of the...

ASTM D8591-25 - Standard Test Method for Determination of Fluorotelomer Alcohols in Test Chamber Air by Thermal Desorption-Gas Chromatography-Triple Quadrupole Tandem Mass Spectrometry (TD-GC-MS/MS)
November 1, 2025 - ASTM International

1.1 This test method covers the detection and quantification of fluorotelomer alcohols (FTOHs), a group of volatile and semivolatile per- and polyfluoroalkyl substances (PFAS), in air samples collected on thermal desorption (TD) tubes by thermal desorption-gas chromatography-triple quadrupole...

ASTM D6639-25 - Standard Guide for Using the Frequency Domain Electromagnetic Method for Subsurface Site Investigations
July 1, 2025 - ASTM International

5.1 Concepts: 5.1.1 This guide summarizes the equipment, field procedures and interpretation methods used for the investigation of subsurface materials and geological structure as based on their properties to conduct, enhance or obstruct the flow of electrical currents induced in the ground by an...

ASTM E1211/E1211M-17(2025) - Standard Practice for Leak Detection and Location Using Surface-Mounted Acoustic Emission Sensors
July 1, 2025 - ASTM International

1.1 This practice describes a passive method for detecting and locating the steady state source of gas and liquid leaking out of a pressurized system. The method employs surface-mounted acoustic emission sensors (for non-contact sensors see Practice E1002), or sensors attached to the system...

ASTM F3263-17(2025) - Standard Guide for Packaging Test Method Validation
October 1, 2025 - ASTM International

4.1 Addressing consensus standards with inter-laboratory studies (ILS) and methods specific to an organization. Test methods need to be validated in many cases, in order to be able to rely on the results. This has to be done at the organization performing the tests but is also performed in the...

ASTM C1576-25 - Standard Test Method for Determination of Slow Crack Growth Parameters of Advanced Ceramics by Constant Stress Flexural Testing (Stress Rupture) at Ambient Temperature
February 1, 2025 - ASTM International

4.1 The service life of many advanced ceramic components is often limited by the subcritical growth (SCG) of cracks over time. In SCG conditions, small subcritical cracks in the ceramic may grow over time under stress in a defined chemical environment at a given temperature (1-3). When one or more...

ASTM E1124-10(2024) - Standard Test Method for Field Measurement of Sound Power Level by the Two-Surface Method
October 1, 2024 - ASTM International

1.1 This test method covers the field, or in situ measurement of sound power level by the two-surface method. The test method is designed to minimize the effects of reverberant conditions, directivity of the noise source under consideration, and the effects of ambient...

ASTM E1746-24 - Standard Test Method for Sampling and Analysis of Liquid Chlorine for Gaseous Impurities
October 1, 2024 - ASTM International

4.1 It is very difficult to exclude sample contamination by ambient air during the process of sampling. The levels of atmospheric contamination caused by poor sampling methods are often equal to or larger than the levels of the gaseous impurities present in the chlorine. This...

Advertisement