4.1 This practice may be used to evaluate the microbial retentivity of any membrane filter used for liquid sterilization where validation is required in the manufacturing of pharmaceutical, biopharmaceutical, and biological products or their intermediates (where applicable). These processes...
This specifications covers alloy-steel bolting material specially heat treated for high-temperature service, such as steam turbine, gas turbine, and similar uses. The grades of steels covered here are: Grade B4B, Grade B4C, and Grade B4D. Steels of Grades B4B and...
4.1 Any risks to final drug product purity from particulate matter on the surfaces of single-use bioprocessing equipment (single-use systems (SUS)) depend on if the SUS is implemented upstream or downstream of sterilizing grade filters or in aseptic processes (see "Recommendations for the...
5.1 This test method provides for the determination of moisture and residue in liquid chlorine. The concentration levels of these impurities are important factors in many commercial uses of liquid chlorine.
1.1 This practice covers reporting particle size measurement data. 1.2 This practice applies to particle size measurement methods, devices, detail levels, and data formats for dry powders, and wet suspensions of solids, gels, or emulsion droplets. This practice does not pertain to...
1.1 These test methods cover the determination of the following properties of refractory shapes: 1.1.1 Apparent porosity, 1.1.2 Liquid absorption, 1.1.3 Apparent specific gravity, and 1.1.4 Bulk density. 1.2 These test methods are applicable to all refractory shapes except those that...
1.1 This test method describes contaminant determination in fuel cell grade hydrogen as specified in relevant ASTM and ISO standards using cavity ring-down spectroscopy (CRDS). This standard test method is for the measurement of one or multiple contaminants including, but not limited to,...
5.1 This test method is intended for use in the laboratory or in the field to evaluate the cleanliness of distillate fuels, and liquid biofuels, such as biodiesel and diesel blends. This specific test method and the precision statement applies to off-line analysis. Note 5: These PCMs can be...
5.1 Residual fuel oils can contain H2S in the liquid phase, and this can result in hazardous vapor phase levels of H2S in storage tank headspaces. The vapor phase levels can vary significantly according to the headspace volume, fuel temperature, and agitation. Measurement of...
4.1 Macroetching is used in the steel industry because it is a simple test that will provide information about the relative homogeneity of the sample. The method employs the action of an acid or other corrosive agent to develop the macrostructural characteristics of a suitably prepared specimen....
5.1 This test method is intended for use in the laboratory or in the field for evaluating the cleanliness of distillate fuels, and liquid bio fuels. It is not applicable to on or in-line applications. 5.2 This test method offers advantage over traditional filtration methods in that it is a...
1.1 These requirements cover mechanical type accessories that are typically intended for attachment to storage tanks or connecting pipe for flammable and combustible liquids in commercial (public) or private (fleet) automotive fueling station and similar storage or dispensing applications...
1.1 These requirements cover mechanical type accessories that are typically intended for attachment to storage tanks or connecting pipe for flammable and combustible liquids in commercial (public) or private (fleet) automotive fueling station and similar storage or dispensing applications...
This specifications covers alloy-steel bolting material specially heat treated for high-temperature service, such as steam turbine, gas turbine, and similar uses. The grades of steels covered here are: Grade B4B, Grade B4C, and Grade B4D. Steels of Grades B4B and...
This document specifies maximum acceptable levels and methods of sampling, extraction and determination for the migration of the elements antimony, arsenic, barium, cadmium, chromium, lead, mercury and selenium from toy materials and from parts of toys. Maximum acceptable levels are...
1.1 This specification2 covers steel castings for valves, flanges, fittings, and other pressure-containing parts intended primarily for low-temperature service. 1.2 Several grades of ferritic steels and one grade of martensitic steel are covered. Selection of analysis will depend on...
5.1 Safety-related service water system (SWS) components are designed to provide adequate cooling to equipment essential to the safe operation and shutdown of the plant. Linings in these systems are installed to maintain the integrity of the system components by preventing corrosion and erosion of...
5.1 This test method is intended for use in the laboratory or in the field to evaluate the cleanliness of distillate fuels, and liquid biofuels, such as biodiesel and diesel blends. This specific test method and the precision statement applies to off-line analysis. Note 4: These PCMs can be...
Narrow Your Results