loading
ASTM D2595-26 - Standard Test Method for Evaporation Loss of Lubricating Greases Over Wide-Temperature Range
July 1, 2026 - ASTM International

1.1 This test method covers the determination of evaporation loss of lubricating greases at temperatures between 93?°C and 316?°C (200?°F and 600?°F). 1.2 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only. 1.3 This standard...

ASTM D7483-26 - Standard Test Method for Determination of Dynamic Viscosity and Derived Kinematic Viscosity of Liquids by Oscillating Piston Viscometer
July 1, 2026 - ASTM International

1.1 This test method covers the measurement of dynamic viscosity and derivation of kinematic viscosity of liquids, such as new and in-service lubricating oils, by means of an oscillating piston viscometer. 1.2 This test method is applicable to Newtonian and non-Newtonian liquids; however the...

ASTM G203-10(2026) - Standard Guide for Determining Friction Energy Dissipation in Reciprocating Tribosystems
June 1, 2026 - ASTM International

1.1 This guide covers and is intended for use in interpreting the friction forces recorded in reciprocating tribosystems. The guide applies to any reciprocating tribosystem, whether it is a wear or fretting test or an actual machine or device. 1.2 The energy dissipation guide was developed in...

ASTM D6079-26 - Standard Test Method for Evaluating Lubricity of Diesel Fuels by the High-Frequency Reciprocating Rig (HFRR)
June 1, 2026 - ASTM International

5.1 Diesel fuel injection equipment has some reliance on lubricating properties of the diesel fuel. Shortened life of engine components, such as diesel fuel injection pumps and injectors, has sometimes been ascribed to lack of lubricity in a diesel fuel. 5.2 The trend of HFRR test results to...

ASTM D7688-26 - Standard Test Method for Evaluating Lubricity of Diesel Fuels by the High-Frequency Reciprocating Rig (HFRR) by Visual Observation
June 1, 2026 - ASTM International

5.1 Diesel fuel injection equipment has some reliance on lubricating properties of the diesel fuel. Shortened life of engine components, such as diesel fuel injection pumps and injectors, has sometimes been ascribed to lack of lubricity in a diesel fuel. 5.2 The trend of HFRR test results to...

ASTM E2905/E2905M-26 - Standard Practice for Examination of Mill and Kiln Girth Gear Teeth—Electromagnetic Methods
July 1, 2026 - ASTM International

Note 1: Throughout the practice, "gear" means gear or pinion unless the gear is specifically identified. 1.1 This practice describes a two-part procedure for examination of gear teeth on mill and kiln gear drives and pinions using eddy current array (ECA) methods. The first part of this practice...

ASTM D3427-26 - Standard Test Method for Air Release Properties of Hydrocarbon Based Oils
June 1, 2026 - ASTM International

5.1 Agitation of lubricating oil with air in equipment, such as bearings, couplings, gears, pumps, and oil return lines, may produce a dispersion of finely divided air bubbles in the oil. If the residence time in the reservoir is too short to allow the air bubbles to rise to the oil surface,...

ASTM D3336-26 - Standard Test Method for Life of Lubricating Greases in Ball Bearings at Elevated Temperatures
May 1, 2026 - ASTM International

1.1 This test method covers the evaluation of the performance of lubricating greases in ball bearings operating under light loads at high speeds and elevated temperatures. 1.2 The values stated in SI units are to be regarded as standard. 1.2.1 Exception-The values given in parentheses are...

ASTM D8112-26 - Standard Guide for Sampling, In-Service Lubricating Oils and Hydraulic Fluids in Industrial Applications
May 1, 2026 - ASTM International

1.1 This guide applies to the collection of representative samples of in-service lubricating oils and hydraulic fluids used in industrial applications to support an effective condition monitoring program. 1.2 Two primary reasons for in-service sampling of lubricating oils and...

ASTM D8126-26 - Standard Test Method for Efficient Basicity Determination by Potentiometric Hydrochloric Acid Titration
June 1, 2026 - ASTM International

1.1 This test method covers a procedure for the determination of the efficient basicity (EBas) in new marine cylinder lubricants that lubricate the upper part, that is, piston-ring-cylinder area, of two-stroke marine engines. 1.2 This test method has been developed for marine cylinder...

ASTM D2070-26 - Standard Test Method for Thermal Stability of Hydraulic Oils
May 1, 2026 - ASTM International

5.1 Thermal stability characterizes physical and chemical property changes which may adversely affect an oil's lubricating performance. This test method evaluates the thermal stability of a hydraulic oil in the presence of copper and steel at 135?°C. No correlation of the test to field...

ASTM D7279-26a - Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids by Automated Houillon Viscometer
May 1, 2026 - ASTM International

1.1 This test method covers the measurement of the kinematic viscosity of transparent and opaque liquids; such as base oils, formulated oils, diesel oil, biodiesel, biodiesel blends, residual fuel oils, marine fuels, and used lubricating oils using a Houillon viscometer in automated mode. 1...

ASTM D1092-26 - Standard Test Method for Measuring Apparent Viscosity of Lubricating Greases
June 1, 2026 - ASTM International

1.1 This test method covers measurement, in poises, of the apparent viscosity of lubricating greases in the temperature range from -54?°C to 38?°C (-65?°F to 100?°F). Measurements are limited to the range from 25?P to 100?000?P at 0.1?s-1 and 1?P to 100?P at 15?000?s-1. Note 1: At very low...

ASTM D5182-26 - Standard Test Method for Evaluating the Scuffing Load Capacity of Oils (FZG A/8.3/90 Method)
May 1, 2026 - ASTM International

1.1 This test method, the Forschungstelle für Záhnräder und Getriebebau (Research Site for Gears and Transmissions) Visual Method, commonly referred to as the FZG Visual Method, is intended to measure the scuffing load capacity of oils used to lubricate hardened steel gears. Scoring, a form...

ASTM D1403-26 - Standard Test Methods for Cone Penetration of Lubricating Grease Using One-Quarter and One-Half Scale Cone Equipment
April 1, 2026 - ASTM International

5.1 These test methods are applicable to greases of National Lubricating Grease Institute (NLGI) consistency numbers 0 to 4 and are intended for use only where the size of the sample prevents the use of Test Methods D217. 5.2 Actual reduced-scale penetration values are not used or reported....

ASTM D7279-26 - Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids by Automated Houillon Viscometer
April 1, 2026 - ASTM International

1.1 This test method covers the measurement of the kinematic viscosity of transparent and opaque liquids; such as base oils, formulated oils, diesel oil, biodiesel, biodiesel blends, residual fuel oils, marine fuels, and used lubricating oils using a Houillon viscometer in automated mode. 1...

ASTM D2596-26 - Standard Test Method for Measurement of Extreme-Pressure Properties of Lubricating Grease (Four-Ball Method)
March 1, 2026 - ASTM International

5.1 This test method, used for specification purposes, differentiates between lubricating greases having low, medium, and high level of extreme-pressure properties. The results do not necessarily correlate with results from service. 5.2 It is noted that lubricating greases that have...

ASTM D7040-26 - Standard Test Method for Determination of Low Levels of Phosphorus in ILSAC GF 4 and Similar Grade Engine Oils by Inductively Coupled Plasma Atomic Emission Spectrometry
March 1, 2026 - ASTM International

5.1 This test method usually requires several minutes per sample. Other test methods which can be used for the determination of phosphorus in lubricating oils include WDXRF Test Method D4927 and ICPAES Test Methods D4951 and D5185. However, this test method provides more precise results than...

ASTM D5800-21(2026) - Standard Test Method for Evaporation Loss of Lubricating Oils by the Noack Method
April 1, 2026 - ASTM International

5.1 The evaporation loss is of particular importance in engine lubrication. Where high temperatures occur, portions of an oil can evaporate. 5.2 Evaporation may contribute to oil consumption in an engine and can lead to a change in the properties of an oil. 5.3 Many engine manufacturers...

ASTM D3525-20(2026)e1 - Standard Test Method for Gasoline Fuel Dilution in Used Gasoline Engine Oils by Wide-Bore Capillary Gas Chromatography
March 15, 2026 - ASTM International

1.1 This test method describes a gas chromatographic technique for determining the amount of gasoline fuel dilution in used lubricating oils arising from their use in gasoline engines. 1.2 This test method is limited to gas chromatographs accommodating wide-bore (0.53?mm) capillary columns...

Advertisement