loading
ASTM D1990-26 - Standard Practice for Establishing Allowable Properties for Visually-Graded Dimension Lumber from In-Grade Tests of Full-Size Specimens
April 15, 2026 - ASTM International

4.1 The procedures described in this practice are intended to be used to establish allowable stress and modulus of elasticity values for solid sawn, visually graded dimension lumber from In-Grade type test data. These procedures apply to the tested and untested sizes and grades when an...

ASTM D6341-26 - Standard Test Method for Determination of the Linear Coefficient of Thermal Expansion of Plastic Lumber and Plastic Lumber Shapes Between -30 and 140°F (-34.4 and 60°C)
February 1, 2026 - ASTM International

1.1 This test method covers the determination of the coefficient of linear thermal expansion for plastic lumber and plastic lumber shapes to two significant figures. The determination is made by taking measurements with a caliper at three discrete temperatures. At the test...

ASTM D8223-19(2026) - Standard Practice for Evaluation of Fire-Retardant Treated Laminated Veneer Lumber
January 1, 2026 - ASTM International

1.1 This practice covers procedures for the evaluation of laminated veneer lumber (LVL) pressure-treated with commercially available fire retardants after exposure to both standard environmental conditions and an extended exposure to elevated temperature. 1.2 LVL products utilizing overlays...

ASTM D7989-26 - Standard Practice for Demonstrating Equivalent In-Plane Lateral Seismic Performance to Wood-Frame Shear Walls Sheathed with Wood Structural Panels
April 1, 2026 - ASTM International

5.1 This practice documents cyclic performance benchmarks for shear walls constructed with wood structural panel (WSP) sheathing attached to dimension lumber framing using common or galvanized box nails as defined in 3.2.8. 5.2 Procedures described in this practice provide a method to...

ASTM D4761-25 - Standard Test Methods for Mechanical Properties of Lumber and Wood-Based Structural Materials
October 15, 2025 - ASTM International

1.1 These test methods cover the determination of the mechanical properties of stress-graded lumber and other wood-based structural materials. 1.2 These test methods appear in the following order: Section Bending edge-wise 6 Bending flat-wise: ?Center-point loading 7 ?Third-point loading 8...

ASTM E2780-10(2026) - Standard Test Method for Determining Particulate Matter Emissions from Wood Heaters
January 1, 2026 - ASTM International

5.1 This test method is used for determining emission rates and emission factors for wood heaters. 5.1.1 The emission factor is useful for determining emission performance during product development. 5.1.2 The emission factor is useful for the air quality regulatory community for determining...

ASTM D8484-25 - Standard Specification for Plastic Lumber Materials and Wood-Plastic Composite Materials Used as Exterior Wall Coverings
June 1, 2025 - ASTM International

1.1 This specification is applicable to the use of plastic lumber materials and of wood-plastic composite materials, and no other plastic composite materials, used as exterior wall coverings, as part of an exterior wall assembly. 1.2 This specification is not applicable to the use of plastic...

ASTM D6782-19(2025) - Standard Test Methods for Standardization and Calibration of In-Line Dry Lumber Moisture Meters
August 1, 2025 - ASTM International

4.1 In-line meters provide a rapid means of detecting moisture content of lumber or wood products in processing (that is, on a continuous production line). Two major uses are monitoring the performance of the drying process (air drying, kiln drying), and providing sorting or identification...

ASTM D245-25 - Standard Practice for Establishing Structural Grades and Related Allowable Properties for Visually Graded Lumber
May 15, 2025 - ASTM International

3.1 Need for Lumber Grading: 3.1.1 Individual pieces of lumber, as they come from the saw, represent a wide range in quality and appearance with respect to freedom from knots, cross grain, shakes, and other characteristics. Such random pieces likewise represent a wide range in...

ASTM D7247-25 - Standard Test Method for Evaluating the Shear Strength of Adhesive Bonds in Laminated Wood Products at Elevated Temperatures
October 15, 2025 - ASTM International

1.1 This standard describes a test method for evaluating the comparative shear strength of a planar adhesive bond at both ambient and elevated temperatures relative to the performance of solid wood under the same conditions. The test method is based on the breaking load after the specimen is...

ASTM D1990-25 - Standard Practice for Establishing Allowable Properties for Visually-Graded Dimension Lumber from In-Grade Tests of Full-Size Specimens
April 1, 2025 - ASTM International

4.1 The procedures described in this practice are intended to be used to establish allowable stress and modulus of elasticity values for solid sawn, visually graded dimension lumber from In-Grade type test data. These procedures apply to the tested and untested sizes and grades when an...

ASTM D3957-09(2025) - Standard Practices for Establishing Stress Grades for Structural Members Used in Log Buildings
August 1, 2025 - ASTM International

1.1 These practices cover the visual stress-grading principles applicable to structural wood members of nonrectangular shape, as typically used in log buildings. These practices are meant to supplement the ASTM standards listed in Section 2, which cover stress-grading of sawn lumber and...

ASTM D4444-25 - Standard Test Method for Laboratory Standardization and Calibration of Hand-Held Moisture Meters
August 1, 2025 - ASTM International

4.1 Hand-held meters provide a rapid means of sampling MC of wood-based materials during and after processing to maintain quality assurance and compliance with standards. These measurements are influenced by actual MC, a number of other wood variables, environmental conditions, geometry of the...

ASTM D7438-20(2025) - Standard Practice for Field Calibration and Application of Hand-Held Moisture Meters
August 1, 2025 - ASTM International

4.1 Hand-held meters provide a rapid means of sampling moisture content of wood-based materials during and after processing to maintain quality assurance and compliance with standards. However, these measurements are inferential; that is, electrical parameters are measured and compared against a...

ASTM D1165-25 - Standard Nomenclature of Commercial Hardwoods and Softwoods
April 1, 2025 - ASTM International

4.1 The purpose of this standard is to provide common tree names and botanical names for commercial species and species groups but is not intended to be all inclusive of commercial practice. The decision about which commercial species are included in this practice is made by the D07 committee on...

ASTM D6117-24 - Standard Test Methods for Mechanical Fasteners in Plastic Lumber and Shapes
December 1, 2024 - ASTM International

6.1 The resistance of plastic lumber and shapes to direct withdrawal of nails, staples, or screws is a measure of its ability to hold or be held to an adjoining object by means of such fasteners. Factors that affect this withdrawal resistance include the physical and mechanical properties of...

ASTM D5664-17(2025) - Standard Test Method for Evaluating the Effects of Fire-Retardant Treatments and Elevated Temperatures on Strength Properties of Fire-Retardant Treated Lumber
January 15, 2025 - ASTM International

5.1 The mechanical properties evaluated by this test method provide the following: 5.1.1 Data for use in developing modification factors for the allowable design properties of fire-retardant treated lumber when used at or near room temperatures (see 6.3). 5.1.2 Data for use in developing...

ASTM D2915-25 - Standard Practice for Sampling and Data-Analysis for Structural Wood and Wood-Based Products
April 1, 2025 - ASTM International

This practice covers sampling and analysis procedures for the investigation and evaluation of allowable properties of specified populations of stress-graded structural lumber. This practice generally assumes that the population is sufficiently large so that, for sampling purposes, it may be...

ASTM D6256/D6256M-25 - Standard Specification for Wood-Cleated Shipping Boxes with Skidded, Load-Bearing Bases
January 1, 2025 - ASTM International

This specification covers the fabrication of wood-cleated shipping boxes with skidded. load-bearing bases designed for nonregulated domestic and overseas shipment of loads under a specified weight limit. Box performance under all atmospheres, handling, shipping, and storage conditions is not...

ASTM D1990-24 - Standard Practice for Establishing Allowable Properties for Visually-Graded Dimension Lumber from In-Grade Tests of Full-Size Specimens
August 1, 2024 - ASTM International

4.1 The procedures described in this practice are intended to be used to establish allowable stress and modulus of elasticity values for solid sawn, visually graded dimension lumber from In-Grade type test data. These procedures apply to the tested and untested sizes and grades when an...

Advertisement