1.1 These reference radiographs illustrate the types and degrees of discontinuities that may be found in aluminum-alloy and magnesium-alloy castings. The castings illustrated are in thicknesses of 1/4 in. (6.35 mm) and 3/4 in. (19.1 mm). The reference radiograph films are an adjunct to this...
1.1 This test method covers quantitatively determining the magnesium sulfate (epsom salt) in leather. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety...
1.1 These test methods cover the chemical analyses usually required for sodium chloride. 1.2 The analytical procedures appear in the following sections: Section Sample Preparation ?5 to? 9 Moisture 10 to 17 Water Insolubles 18 to 26 Calcium and Magnesium 27 to 34 Sulfate 35 to 42 Reporting...
This specification covers the general requirements for steel sheet in coils and cut length, metallic-coated on continuous lines by the hot-dip process. This material is intended for applications requiring corrosion resistance. Hot-dip metallic coatings are available in six different types: zinc and...
1.1 These digital reference images illustrate the types and degrees of discontinuities that may be found in magnesium-alloy castings. The castings illustrated are in thicknesses of 1/4 in. (6 mm) and 3/4 in. (19.1 mm). 1.2 All areas of this standard may be open to agreement between the...
1.1 These test methods cover procedures for sampling and testing coal ash and raw or calcined pozzolans for use in concrete. 1.2 The procedures appear in the following order: Sections Sampling 7 CHEMICAL ANALYSIS Reagents and apparatus 10 Moisture content 11 and 12 Loss on ignition 13 and 14...
1.1 These reference radiographs illustrate various types and severity levels of discontinuities in aluminum fusion welds that may be revealed by radiographic examination. These reference radiographs do not specify the acceptable level of these discontinuities, rather they provide a visual reference...
This specification covers sintered aluminium structural parts made primarily from aluminum powders to which controlled amounts of master alloys or elemental copper, magnesium, and silicon have been added by blending. Structural parts shall be made by molding and sintering metal powders to...
1.1 This test method assesses metal or other ions released from single-use, metallic, implantable medical devices or components thereof by exposing the device to solutions simulating the in vivo environment and temperature in a container for a predetermined time frame with regular sampling at...
1.1 This terminology covers the principal terms and definitions relating to aluminum- and magnesium-alloy products. It is published to encourage uniformity of terminology throughout Committee B07 product specifications. 1.2 Certain definitions and definitions of terms specific to a standard...
This specification covers aluminum-base and zinc-base master alloys used to make zinc die-casting alloys. The material may be made by any suitable process. The material covered by this specification shall be of uniform quality and shall be free of dross, flux, or other harmful contamination. If the...
1.1 This terminology covers the principal terms and definitions relating to aluminum- and magnesium-alloy products. It is published to encourage uniformity of terminology throughout Committee B07 product specifications. 1.2 Certain definitions and definitions of terms specific to a standard...
1.1 This test method covers analysis of magnesian, dolomitic and high-calcium limes for total neutralizing capability and dissolved major oxides. Dissolved calcium and magnesium are the major species that neutralize acid under the conditions of the test. 1.2 The test conditions are chosen to...
This specification covers two commercial zinc alloys, namely: Slush Casting Alloy A (Z34510) and Slush Casting Alloy B (Z30500), in ingot form for remelting for the manufacture of castings. This slush casting alloys are used primarily for the manufacture of hollow castings such as lighting...
This specification covers the standard requirements for commercial zinc casting alloys in ingot form for use in the manufacture of sheet metal forming dies, sand cast or plaster cast forming dies, and plastic injection molds. Kirksite A alloy (UNS Z35543) is intended for use in the fabrication of...
1.1 This test method covers the determination of the approximate chloride (salts) concentration in crude oil. The range of concentration covered is 3.5?mg/kg to 500?mg/kg or 1.0?lb/1000 bbl to 150?lb/1000 bbl (PTB) as chloride concentration/volume
This specification covers steel sheet in coils and cut lengths coated with zinc-aluminum-magnesium alloy by hot-dip process intended for applications requiring corrosion resistance and paintability. The steel sheet shall be produced in the following designations: commercial steel (CS types...
1.1 The purpose of this standard is to outline appropriate experimental approaches for conducting an initial evaluation of the in vitro degradation properties of a device or test sample fabricated from an absorbable metal or alloy. 1.2 The described experimental approaches are intended to control...
1.1 This guide outlines an appropriate experimental approach for evaluating the effects of physiologically relevant constant or cyclic loads (e.g. stresses, strains) on the performance characteristics of an absorbable metal implant or test specimen. 1.2 The intent of this guide is to encompass...
1.1 These test methods cover the determination of the operating capacity of particulate cation-exchange materials when used for the removal of calcium, magnesium, and sodium ions from water. It is intended for use in testing both new and used materials. The following two test methods are...
Narrow Your Results