loading
ASTM D8120-25 - Standard Test Method for Ferrous Debris Quantification
July 1, 2025 - ASTM International

1.1 This test method describes a means for quantitative determination of the concentration of ferrous debris in lubricants and greases. 1.2 This test method provides a determination of the concentration of ferrous debris in the lubricant or grease from a nominal 0 mg/kg to 10?000 mg/kg (1 % by...

ASTM D7046-25 - Standard Guide for Use of the Metal Detection Method for Subsurface Site Investigations
July 1, 2025 - ASTM International

1.1 Purpose and Application-This guide summarizes the equipment, field procedures, and interpretation methods for the assessment of subsurface materials using the electromagnetic (EM) metal detection method and therefore in this guide the term "metal detector" is used to refer to an EM metal...

ASTM C1238-24 - Standard Guide for Installation of Walk-Through Metal Detectors
October 1, 2024 - ASTM International

1.1 This guide describes various elements (for examples, see Appendix X2) to be considered when planning to install walk-through metal detectors (WTMDs). The installation of WTMDs should only be accomplished by manufacturer-trained staff/personnel. 1.2 This guide applies to either permanent or...

Fault Tolerant Attitude Estimation for Small Satellites
December 23, 2020 - CRC

Small satellites use commercial off-the-shelf sensors and actuators for attitude determination and control (ADC) to reduce the cost. These sensors and actuators are usually not as robust as the available, more expensive, space-proven equipment. As a result, the ADC system of small satellites is...

ASTM D8184 - Standard Test Method for Ferrous Wear Debris Monitoring in In-Service Fluids Using a Particle Quantifier Instrument
May 15, 2018 - ASTM

This test method describes the use of offline particle quantification (often referred to as PQ) magnetometers to trend wear rates in machinery by monitoring the amount of ferromagnetic material suspended in a fluid sample that has been in contact with the moving parts of the machinery. It is...

ASTM D8184-18 - Standard Test Method for Ferrous Wear Debris Monitoring in In-Service Fluids Using a Particle Quantifier Instrument
May 15, 2018 - ASTM International

1.1 This test method describes the use of offline particle quantification (often referred to as PQ) magnetometers to trend wear rates in machinery by monitoring the amount of ferromagnetic material suspended in a fluid sample that has been in contact with the moving parts of the machinery....

ASTM D8184-18e1 - Standard Test Method for Ferrous Wear Debris Monitoring in In-Service Fluids Using a Particle Quantifier Instrument
May 15, 2018 - ASTM International

1.1 This test method describes the use of offline particle quantification (often referred to as PQ) magnetometers to trend wear rates in machinery by monitoring the amount of ferromagnetic material suspended in a fluid sample that has been in contact with the moving parts of the machinery....

IEEE 2700 - Sensor Performance Parameter Definitions
June 15, 2017 - IEEE

This standard provides a common framework for sensor performance specification terminology, units, conditions, and limits. This standard is intended for sensor technologies with digital I/O interfaces. The specific sensors discussed in this standard are the accelerometer, magnetometer,...

ASTM D8120 - Standard Test Method for Ferrous Debris Quantification
June 1, 2017 - ASTM

This test method describes a means for quantitative determination of the concentration of ferrous debris in lubricants and greases. This test method provides a determination of the concentration of ferrous debris in the lubricant or grease from a nominal 0 mg/kg to 10 000 mg/kg (1 % by mass) or...

ASTM D8120-17 - Standard Test Method for Ferrous Debris Quantification
June 1, 2017 - ASTM International

1.1 This test method describes a means for quantitative determination of the concentration of ferrous debris in lubricants and greases. 1.2 This test method provides a determination of the concentration of ferrous debris in the lubricant or grease from a nominal 0 mg/kg to 10 000 mg/kg (1 % by...

IEC 61788-13 - Superconductivity – Part 13: AC loss measurements – Magnetometer methods for hysteresis loss in superconducting multifilamentary composites
July 1, 2012 - IEC

This part of IEC 61788 describes considerations for the measurement of hysteretic loss in Cu/Nb-Ti multifilamentary composites using DC- or low-ramp-rate magnetometry. This international standard specifies a method of the measurement of hysteretic loss in multifilamentary Cu/Nb-Ti composite...

IEC/TR 62797 - International comparison of measurements of the magnetic moment using vibrating sample magnetometers (VSM) and superconducting quantum interference device (SQUID) magnetometers
August 1, 2013 - IEC

This Technical Report provides the results of an international comparison of measurements of the magnetic moment, using vibrating sample magnetometers (VSM) and superconducting quantum interference device (SQUID) magnetometers. The basic object of this comparison is to verify the...

DS/EN 61788-13 - Superconductivity - Part 13: AC loss measurements - Magnetometer methods for hysteresis loss in superconducting multifilamentary composites
November 12, 2012 - DS

IEC 61788-13:2012 describes considerations for the measurement of hysteretic loss in Cu/Nb-Ti multifilamentary composites using DC- or low-ramp-rate magnetometry. This international standard specifies a method of the measurement of hysteretic loss in multifilamentary Cu/Nb-Ti composite conductors....

Smart Sensors for Industrial Applications
May 29, 2013 - CRC

Sensor technologies are a rapidly growing area of interest in science and product design, embracing developments in electronics, photonics, mechanics, chemistry, and biology. Their presence is widespread in everyday life, where they are used to sense sound, movement, and optical or magnetic signals...

ASTM A894/A894M-00(2011)e1 - Standard Test Method for Saturation Magnetization or Induction of Nonmetallic Magnetic Materials (Withdrawn 2017)
October 1, 2011 - ASTM International

This test method deals with the standard practice of measuring saturation magnetization or induction of nonmetallic magnetic materials using a vibrating sample magnetometer, which could be commercially purchased from a manufacturer or constructed with normal machine shop facilities. The test...

ASTM D7046 - Standard Guide for Use of the Metal Detection Method for Subsurface Exploration
May 1, 2011 - ASTM

Purpose and Application-This guide summarizes the equipment, field procedures, and interpretation methods for the assessment of subsurface materials using the metal detection method. Metal detectors respond to the presence of both ferrous and nonferrous metals by inducing eddy currents in...

Advertisement