1.1 This test method describes a means for quantitative determination of the concentration of ferrous debris in lubricants and greases. 1.2 This test method provides a determination of the concentration of ferrous debris in the lubricant or grease from a nominal 0 mg/kg to 10?000 mg/kg (1 % by...
1.1 Purpose and Application-This guide summarizes the equipment, field procedures, and interpretation methods for the assessment of subsurface materials using the electromagnetic (EM) metal detection method and therefore in this guide the term "metal detector" is used to refer to an EM metal...
1.1 This guide describes various elements (for examples, see Appendix X2) to be considered when planning to install walk-through metal detectors (WTMDs). The installation of WTMDs should only be accomplished by manufacturer-trained
Small satellites use commercial off-the-shelf sensors and actuators for attitude determination and control (ADC) to reduce the cost. These sensors and actuators are usually not as robust as the available, more expensive, space-proven equipment. As a result, the ADC system of small satellites is...
This test method describes the use of offline particle quantification (often referred to as PQ) magnetometers to trend wear rates in machinery by monitoring the amount of ferromagnetic material suspended in a fluid sample that has been in contact with the moving parts of the machinery. It is...
1.1 This test method describes the use of offline particle quantification (often referred to as PQ) magnetometers to trend wear rates in machinery by monitoring the amount of ferromagnetic material suspended in a fluid sample that has been in contact with the moving parts of the machinery....
1.1 This test method describes the use of offline particle quantification (often referred to as PQ) magnetometers to trend wear rates in machinery by monitoring the amount of ferromagnetic material suspended in a fluid sample that has been in contact with the moving parts of the machinery....
This standard provides a common framework for sensor performance specification terminology, units, conditions, and limits. This standard is intended for sensor technologies with digital I/O interfaces. The specific sensors discussed in this standard are the accelerometer, magnetometer,...
This test method describes a means for quantitative determination of the concentration of ferrous debris in lubricants and greases. This test method provides a determination of the concentration of ferrous debris in the lubricant or grease from a nominal 0 mg/kg to 10 000 mg/kg (1 % by mass) or...
1.1 This test method describes a means for quantitative determination of the concentration of ferrous debris in lubricants and greases. 1.2 This test method provides a determination of the concentration of ferrous debris in the lubricant or grease from a nominal 0 mg/kg to 10 000 mg/kg (1 % by...
This part of IEC 61788 describes considerations for the measurement of hysteretic loss in Cu/Nb-Ti multifilamentary composites using DC- or low-ramp-rate magnetometry. This international standard specifies a method of the measurement of hysteretic loss in multifilamentary Cu/Nb-Ti composite...
This Technical Report provides the results of an international comparison of measurements of the magnetic moment, using vibrating sample magnetometers (VSM) and superconducting quantum interference device (SQUID) magnetometers. The basic object of this comparison is to verify the...
IEC 61788-13:2012 describes considerations for the measurement of hysteretic loss in Cu/Nb-Ti multifilamentary composites using DC- or low-ramp-rate magnetometry. This international standard specifies a method of the measurement of hysteretic loss in multifilamentary Cu/Nb-Ti composite conductors....
Sensor technologies are a rapidly growing area of interest in science and product design, embracing developments in electronics, photonics, mechanics, chemistry, and biology. Their presence is widespread in everyday life, where they are used to sense sound, movement, and optical or magnetic signals...
This test method deals with the standard practice of measuring saturation magnetization or induction of nonmetallic magnetic materials using a vibrating sample magnetometer, which could be commercially purchased from a manufacturer or constructed with normal machine shop facilities. The test...
Purpose and Application-This guide summarizes the equipment, field procedures, and interpretation methods for the assessment of subsurface materials using the metal detection method. Metal detectors respond to the presence of both ferrous and nonferrous metals by inducing eddy currents in...
Narrow Your Results