loading
ASTM D6884-26 - Standard Practice for Installation of Articulating Concrete Block (ACB) Revetment Systems
March 15, 2026 - ASTM International

5.1 An articulating concrete block system is comprised of a matrix of individual concrete blocks placed together to form an erosion-resistant system with specific hydraulic performance characteristics. These systems in practice are commonly referred to as ACB revetment systems. The system includes...

ASTM D8569-26 - Standard Practice for Surface Sampling of Non-Volatile and Semi-Volatile Organic Chemicals for Worker Protection
January 1, 2026 - ASTM International

1.1 This practice covers criteria to be used in defining strategies for sampling nonvolatile and semi-volatile organic chemicals on surfaces for workplace health and safety monitoring. Guidance is also given for the use of direct reading techniques, such as colorimetric measurement. 1.2 Relevant...

ASTM D6031/D6031M-25 - Standard Test Method for Nuclear Gauge Logging In Situ Water Content and Density of Soil and Rock in Drilled Access Holes or Trenches Using Horizontal, Slanted, and Vertical Access Tubes
October 15, 2025 - ASTM International

1.1 This test method covers collection and comparison of logs of thermalized-neutron counts and back-scattered gamma counts along horizontal or vertical air-filled access tubes. 1.2 Access tubes are installed either by drilling access holes or digging a trench into the media being measured....

ASTM G111-21a(2025) - Standard Guide for Corrosion Tests in High Temperature or High Pressure Environment, or Both
October 1, 2025 - ASTM International

5.1 Autoclave tests are commonly used to evaluate the corrosion performance of metallic and non-metallic materials under simulated HP and HTHP service conditions. Examples of service environments in which HP and HTHP corrosion tests have been used include chemical processing, petroleum production...

ASTM D7917-25 - Standard Practice for Inductive Wear Debris Sensors in Gearbox and Drivetrain Applications
June 15, 2025 - ASTM International

5.1 This practice is intended for the application of online, full-flow, or bypass, or kidney loop sampling of wear debris via inductive sensors for gearbox and drivetrain applications. 5.2 Periodic sampling and analysis of lubricants have long been used as a means to determine overall machinery...

ASTM D2435/D2435M-25 - Standard Test Methods for One-Dimensional Consolidation Properties of Soils Using Incremental Loading
June 1, 2025 - ASTM International

1.1 These test methods cover procedures for determining the magnitude and rate of consolidation of soil when it is restrained laterally and drained axially while subjected to incrementally applied controlled-stress loading. Two alternative methods are provided as follows: 1.1.1 Test Method A-This...

ASTM D8593-24 - Standard Test Method for Determining the Physical Properties of Horticultural Growing Media Utilizing a Porometer
December 1, 2024 - ASTM International

1.1 This test method is designed to determine the properties of the structure for substrates and components used in horticulture as a growth media. The total porosity, container capacity, and air space are three properties that are determined on a percent volume basis using this method....

ASTM E3439-25 - Standard Guide for PFAS Data Evaluation
March 1, 2025 - ASTM International

1.1 This guidance discusses several aspects that are critical for assessing, evaluating, and interpreting per- and polyfluoroalkyl substances (PFAS) data received from analytical laboratories: project planning, data quality assessment, data validation, and ultimately, data usability and evaluation....

ASTM D5116-25 - Standard Guide for Small-Scale Environmental Chamber Determinations of Organic Emissions from Indoor Materials/Products
February 1, 2025 - ASTM International

1.1 This guide provides direction on the measurement of the emissions of volatile organic compounds (VOCs) from indoor materials and products using small-scale environmental test chambers. 1.2 This guide pertains to chambers that fully enclose a material specimen to be tested and does not address...

ASTM E3488-25 - Standard Guide for Moving Sites to Closure (MStC) for Petroleum Underground Storage Tank (UST) Releases
April 1, 2025 - ASTM International

4.1 This guide is intended for use primarily by responsible parties, corrective action professionals, regulators, and others who desire to secure regulatory closure or an NFA certification from the applicable regulatory oversight agency at petroleum UST sites requiring corrective actions. While the...

ASTM F3716-25 - Standard Test Method for Cumulative Population Doubling Analysis of the Proliferation of Vertebrate Tissue Cell Preparations
February 15, 2025 - ASTM International

5.1 Background for CPD Analyses for in vitro Vertebrate Tissue Cell Proliferation Studies-Since Leonard Hayflick's early reports on in vitro tissue cell culture studies in the 1960s, CPD data derived from serial cell culture have been used in in vitro tissue cell research as a basis for evaluating...

Heat and Mass Transfer in Drying of Porous Media
August 2, 2019 - CRC

Heat and Mass Transfer in Drying of Porous Media offers a comprehensive review of heat and mass transfer phenomena and mechanisms in drying of porous materials. It covers pore-scale and macro-scale models, includes various drying technologies, and discusses the drying dynamics...

ASTM B680-24 - Standard Test Method for Seal Quality of Anodic Coatings on Aluminum by Acid Dissolution
June 1, 2024 - ASTM International

3.1 This test method describes a destructive test procedure for measuring the degree of seal of the porosity in anodic oxide coatings. Low coating mass loss is an indication of good seal quality and of the ability of the coating to resist staining and "blooming" in many types of service. 3.2...

JIS INFORM RECORD MEDIA - JIS Information Recording Media Handbook
January 1, 2016 - JSA
A description is not available for this item.
ASTM D8560-24 - Standard Guide for Determination of Airborne PFAS in the Indoor Air Environment
April 1, 2024 - ASTM International

1.1 This guide describes methods for determining Per- and Polyfluoroalkyl Substances (PFAS) concentrations in indoor air. 1.2 This guide is focused on PFAS measurement technologies applicable to indoor air (including in vehicles and indoor workplaces) and other relevant air volumes such as, air in...

ASTM D6031/D6031M-24 - Standard Test Method for Logging In Situ Moisture Content and Density of Soil and Rock by the Nuclear Method in Horizontal, Slanted, and Vertical Access Tubes
January 1, 2024 - ASTM International

1.1 This test method covers collection and comparison of logs of thermalized-neutron counts and back-scattered gamma counts along horizontal or vertical air-filled access tubes. 1.2 For limitations, see Section 6, "Interferences." 1.3 The in situ water content in mass per unit volume and the...

ASTM D4096-17(2023) - Standard Test Method for Determination of Total Suspended Particulate Matter in the Atmosphere (High-Volume Sampler Method)
November 1, 2023 - ASTM International

1.1 This test method provides for sampling a large volume of atmosphere, 1600?m3 to 2400?m3 (55 000?ft3 to 85 000?ft3), by means of a high flow-rate vacuum pump at a rate of 1.13?m3/min to 1.70?m3/min (40?ft3/min to 60?ft3/min) (1-4).2 1.2 This flow rate allows suspended particles having diameters...

ASTM D7277-16(2023) - Standard Test Method for Performance Testing of Articulating Concrete Block (ACB) Revetment Systems for Hydraulic Stability in Open Channel Flow
August 1, 2023 - ASTM International

1.1 The purpose of this test method is to provide specifications for the hydraulic testing of full-scale articulating concrete block (ACB) revetment systems under controlled laboratory conditions for purposes of identifying stability performance in steep slope, high-velocity flows. The testing...

ASTM B136-23 - Standard Test Method for Measurement of Stain Resistance of Anodic Coatings on Aluminum
May 1, 2023 - ASTM International

1.1 This test method is intended to determine whether anodic oxide coatings on aluminum and its alloys, that have undergone a sealing treatment and contact with an acid solution, are stainproof or nonadsorptive with respect to dyes. 1.2 Coatings that have been properly sealed should be proof...

ASTM D8141-22 - Standard Guide for Selecting Volatile Organic Compounds (VOCs) and Semi-Volatile Organic Compounds (SVOCs) Emission Testing Methods to Determine Emission Parameters for Modeling of Indoor Environments
November 1, 2022 - ASTM International

4.1 Emissions of VOCs are typically controlled by internal mass-transfer limitations (for example, diffusion through the material), while emissions of SVOCs are typically controlled by external mass-transfer limitations (migration through the air immediately above the material). The...

Advertisement