1.1 This test method covers the energy dispersive X-ray fluorescence (EDXRF) spectrochemical analysis of trace levels of uranium and thorium in soils. Any sample matrix that differs from the general ground soil composition used for calibration (that is, fertilizer or a sample of mostly rock)...
4.1 The rubber-filler interaction needed in silica technology for the rubber industry is based on the use of silane-coupling agents that react with the silanol groups on the surface of the silica during the processing step called silanization. Silane-coupling agents are multifunctional molecules...
4.1 The results obtained from this method can be used to determine the unit weight of compacted asphalt mixtures, and in conjunction with Test Method D3203, to obtain percent air voids. These values in turn may be used in determining the relative degree of compaction. 4.2 Since specific gravity has...
5.1 This AE examination is useful to detect micro-damage generation, accumulation, and growth of new or existing flaws. The examination is also used to detect significant existing damage from friction-based AE generated during loading or unloading of these regions. The damage mechanisms that can be...
1.1 This test method determines the quasi-static longitudinal tensile strength and elongation properties of fiber reinforced polymer matrix (FRP) composite bars commonly used as tensile elements in reinforced, prestressed, or post-tensioned concrete. Note 1: Additional procedures for...
4.1 This test method may be used for material development, material comparison, quality assurance, characterization, and design data generation. 4.2 Continuous fiber-reinforced ceramic matrix composites generally are characterized by glass or fine grain-sized (<50?μm) ceramic matrices and...
1.1 This test method is used to establish the concentration of free cyanide in an aqueous wastewater, effluent and in-stream free cyanide concentrations after mixing treated water with receiving water. The test conditions of this test method are used to measure free cyanide (HCN and CN-) and...
1.1 This guide covers the identification and quantitation of organic compounds by gas chromatography/mass spectrometry (GC-MS) (electron impact) that are present or extracted from water and are capable of passing through a gas chromatograph without alteration. This guide can be used to provide...
5.1 Matrix spiking is commonly used to determine the bias under specific analytical conditions, or the applicability of a test method to a particular sample matrix in that context, by determining the extent to which the spiked analyte or component is recovered from the sample...
1.1 This test method covers the determination of dissolved elements in ground waters, surface waters, and drinking water. It may also be used for determination of total recoverable or total element concentrations in these waters as well as wastewater, mine-impacted waters, and digested biosolids,...
5.1 This test method is intended to determine alkaline resistance data for material specifications, research and development, quality assurance, and structural design and analysis. Depending on the procedure and test matrix, the primary test results are the mass change and tensile capacity...
5.1 This guide is intended to provide machinery maintenance and monitoring personnel with a guideline for performing filter debris analysis as a means to determine machine condition. Correlating the filter contaminants to 'normal' and 'abnormal' lube system operation provides early indication of a...
5.1 Properties determined by this test method are useful in the evaluation of new fibers at the research and development levels. Fibers with diameters up to 250 × 10-6 m are covered by this test method. Very short fibers (including whiskers) call for specialized test techniques (1) and are not...
5.1 Ambient marine waters generally contain very low concentrations of toxic metals that require sensitive analytical methods, such as ICP-MS, to detect and measure the metal's concentrations. 5.2 Due to the high dissolved salt concentrations present in seawater, sample pretreatment is required to...
1.1 This test method addresses the uniaxial compression of a double-notched test specimen to determine interlaminar shear strength of continuous fiber-reinforced ceramic composites (CFCCs) at elevated temperatures. Failure of the test specimen occurs by interlaminar shear between two centrally...
5.1 The analysis of many types of water for metals using flame atomic absorption spectrophotometry, inductively coupled plasma emission spectrophotometry, direct current plasma emission spectrophotometry, or graphite furnace atomic absorption spectrophotometry necessitates the use of a digestion...
1.1 This standard intends to serve as a foundational document for individuals and organizations involved in the development, production, delivery, and regulation of extracellular matrices (ECMs) and related tissue products used in tissue engineered medical products (TEMPs). 1.2 This standard...
4.1 This guide deals with the difficult problem of benchmarking neutron transport calculations carried out to determine fluences for plant-specific reactor geometries. The calculations are necessary for fluence determination in locations important for material radiation damage estimation and which...
5.1 Fracture mirror size analysis is a powerful tool for analyzing glass and ceramic fractures. Fracture mirrors are tell-tale fractographic markings in brittle materials that surround a fracture origin as discussed in Practices C1256 and C1322. Fig. 1 shows a schematic with key features identified...
Narrow Your Results