This European Standard defines the principal dimensions for the internal installation of single and multiple mechanical seals with (rotating) spring units into the sealing cavity according to ISO 3069 as minimum cavity dimensions as typical for centrifugal pumps in accordance with EN...
5.1 Test Method F88 has been the standard for the mechanical peel strength testing of peelable seals since the 1960s. Normally the testing is run on a portion of the seal. The result is an actual seal strength picture of that portion of the seal. This test method...
5.1 These practices may be used to determine whether a RO or NF device is free of leaks if the mechanical integrity of the device is to be confirmed. They may also be used to detect leaks in RO or NF devices whose operating performance indicates a possible leak. These practices may be used...
1.1 This specification covers flat steel strapping and seals intended for use in closing, reinforcing, bundling articles for shipment, unitizing, palletizing, and bracing for carloading, truckloading, lifting, and lashing. 1.2 This specification includes strapping and seals made from...
1.1 It is the intent of this practice to permit an investigator to evaluate the oxidative stability of UHMWPE materials as a function of processing and sterilization method. This practice describes a laboratory procedure for accelerated aging of ultra-high molecular weight polyethylene (UHMWPE)...
Test Method F88 has been the standard for the mechanical peel strength testing of peelable seals since the 1960s. Normally the testing is run on a portion of the seal. The result is an actual seal strength picture of that portion of the seal. This test method is...
Test Method F88 has been the standard for the mechanical peel strength testing of peelable seals since the 1960s. Normally the testing is run on a portion of the seal. The result is an actual seal strength picture of that portion of the seal. This test method is...
1.1 This specification covers the requirements for fabricated alumina parts suitable for electronic and electrical applications and ceramic-to-metal seals as used in electron devices. This specification specifies limits and methods of test for electrical, mechanical, thermal, and...
This specification covers aluminum 1350-H19, 1350-H16 or -H26, 1350-H14 or -H24, 1350-H142 or -H242, and aluminum alloy 8XXX series for tempers "O" and H1X or H2X, bare stranded conductors composed of one or more roller shaped or die compressed layers of helically laid wires. The conductors are for...
This document specifies accelerated moisture absorption properties and supersaturated conditioning by moisture for fibre-reinforced plastics) using sealed pressure vessel at higher temperature than 100 °C with saturated water vapour at used heating temperature. The purpose of this moisture...
5.1 The performance and quality of steam-treated materials depends upon the surface cleanliness of the material prior to steam treatment and the adequacy of the processing. Steam treatment can be used as a decorative coating, producing a blue-gray to a blue-black appearance. It can reduce the...
2.1 Molybdenum is used in engineering applications where strength and rigidity of component parts are needed, especially at high temperatures. Its good strength at high temperatures, low vapor pressure, and good impact and creep resistance make it attractive for load-bearing items such as turbine...
5.1 When a constant strain is imposed on rubber, the force necessary to maintain that strain is not constant but decreases with time; this phenomenon is called force decay (stress relaxation). Conversely, when rubber is subjected to a constant stress, an increase in the deformation takes place in...
1.1 This specification establishes the performance characteristics required for Metallic Press-Connect Fittings for use in piping and tubing systems with a maximum allowable working pressure of three-hundred pounds per square inch (300 psi) [2.07 MPa]. These fittings directly attach to pipe or tube...
1.1 This test method is used to determine the degree and rate of aerobic degradation (as indicated by loss of tensile strength, molecular weight, possibly resulting in disintegration and fragmentation) and anaerobic biodegradation of plastic materials in an accelerated aerobic-anaerobic bioreactor...
This specification covers the requirements for porous oxide coatings deposited by electrolysis on aluminum and aluminum alloy parts. These coatings should have good appearance, abrasion resistance, electrical properties, and protection against corrosion and does not include nonporous barrier layer...
1.1 This specification describes products composed of dense thermoplastic elastomers that are fabricated into gaskets and accessories (such as compression seals, setting blocks, spacers, and shims) for use in sealing and glazing applications in building construction. These products are used...
1.1 This specification is intended to be a means of calling out finished machined parts ready for commercial use. 1.2 This specification establishes requirements for parts machined from unplasticized, 100 % polychlorotrifluoroe
1.1 These practices cover two classes of treatment for preparation of magnesium alloy surfaces for painting, as follows: Class I-Chemical Treatments. Class II-Anodic Treatments. In general, the latter treatments are the more protective of the two classes. Mechanical (abrasive) treatments,...