1.1 This specification covers various designs of welded wire mesh or twisted (woven) hexagonal wire mesh, zinc coated before fabrication, to be used as reinforcement for the concrete applied in the manufacture of negative buoyancy pipe needed for laying pipe in marshes or in water....
1.1 This guide pertains to removal and analysis techniques to extract debris captured by in-service lubricant and hydraulic filters and to analyze the debris removed. 1.2 This guide suggests techniques to remove, collect and analyze debris from filters in support of machinery health condition...
This specification covers woven or welded galvanized steel wire fabric commercially known as hardware cloth. It is customarily used for window and screen door guards, tree guards, industrial machine guards, sand screens, and grain bins. It serves as a protective screen against rodents and is used...
1.1 This specification covers the use of an aramid fiber reinforced polymer (AFRP) composite mesh product, provided in a pre-manufactured weave architecture. The composite mesh is placed within the concrete cover of reinforced concrete structures, typically installed on the form work...
1.1 This specification covers zinc-coated fence fabric intended for enclosure of poultry, or to prevent entry into special areas. It is available in three styles as: 1.1.1 Poultry Netting, consisting of a mesh of woven wire with openings hexagonal in shape, 1.1.2 Poultry-and-Garden Fence...
1.1 These test methods cover procedures for the sampling and testing of the various ferroalloys for sizing, either before or after shipment from the plants of the manufacturers. 1.2 They are designed to give results representative of each lot that will be comparable with the manufacturer's...
1.1 This specification covers PB Exterior Insulation and Finish Systems (EIFS) defined as an exterior, non-bearing wall covering providing a weather-resistant exterior wall envelope on walls required to be combustible or noncombustible, fire-resistance-rate
1.1 This consumer safety performance specification establishes performance requirements, test methods, and marking requirements to promote the safe use of cribs in commercial environments such as hotels, rentals, motels, and child care centers and the like. 1.2 This consumer safety performance...
5.1 This practice is intended to provide consistent criteria, references and operational considerations in the specifications, management and construction of institutional trampoline courts. 5.2 This practice applies to architects, designers, engineers, construction contractors, manufacturers,...
This specification covers polyvinyl chloride and other conforming organic polymer-coated steel chain-link fabric, coated before weaving. Fabric produced from three classes of wire coatings are covered as follows: Class I consists of polymer coatings extruded over zinc-coated, aluminum-coated, or...
This specification covers the general and physical requirements for commercial standard solar screening woven from vinyl-coated fiber glass yarn. The material shall conform to general and physical requirements of this specification. General requirements include workmanship, plasticizers, color,...
This specification covers the requirements for insect screening and louver cloth made from vinyl-coated glass yarns. Specifically covered here are: commercial standard vinyl-coated glass yarn insect screening designed and woven primarily for installation in or on any dwelling, patio, screening...
4.1 This section provides a description of the environmental conditions listed in Section 1 and describes the sub-conditions within each condition. Examples provided for many of the conditions and sub-conditions are provided as guidance only. Each of the conditions described should be evaluated and...
1.1 This specification covers external sealing bands to be used in conjunction with concrete pipe as defined in Terminology C822 and conforming to Specifications C14, C76, C412, C478/C478M, C506, C507, C655, C985, C1417, and C1433. 1.1.1 Type I, Rubber and Mastic Bands. 1.1.2 Type II, Plastic Film...
1.1 This test method covers the measurement of flexural stiffness properties of medical textiles (for example, surgical mesh, films, and membranes). Bending length is measured and flexural rigidity is calculated. 1.2 This test method may be used for absorbable or non-absorbable medical...
5.1 This performance specification identifies electrical, thermal, and mechanical performance characteristics for conductive clothing and its components. 5.1.1 The measured data provides information that the buyer can use when selecting conductive clothing used in Type 1 (for example, barehand...
1.1 This practice covers the preparation of specimens of mastics and coatings in the form of cured sheets or films that are used in other procedures for evaluation of physical properties. 1.2 Three procedures are described for casting and curing (Note 1) mastics and coatings of all types for...
1.1 This test method covers the equipment, field procedures, and interpretation of the results for the pavement thickness measurements produced by a magnetic pulse induction (MPI) device. Magnetic pulse induction devices induce a weak-pulsed magnetic field that causes the induction of eddy currents...
4.1 This section provides a description of the environmental conditions listed in Section 1 and describes the sub-conditions within each condition. Examples provided for many of the conditions and sub-conditions are provided as guidance only. Each of the conditions described should be evaluated and...
5.1 This test method evaluates the engagement between the window and insect screen under static loading for the appropriate specifying authorities or as a design tool for manufacturers. The ability of insect screens to remain engaged depends on the magnitude, duration, repetition of loads, and the...
Narrow Your Results