loading
MPIF METAL MATRIX - Metal Matrix Composites
January 1, 2006 - MPIF
A description is not available for this item.
MPIF METALLOGRAPHIC ETCH - Metallographic Etching
January 1, 1999 - MPIF
A description is not available for this item.
MPIF METALS HANDBOOK - Metals Handbook
January 1, 1998 - MPIF
A description is not available for this item.
MPIF METALLOGRAPHY PRINCI - Metallography Principles and Practice
January 1, 1984 - MPIF
A description is not available for this item.
MPIF METALS ALLOYS - PARTICLE STRENGTHENING OF METALS AND ALLOYS
MPIF
A description is not available for this item.
MPIF METAL INJECTION - PART 19 - METAL INJECTION MOLDING
MPIF
A description is not available for this item.
MPIF METAL VOLUME 4 - METAL AND CERAMIC INJECTION MOLDING
MPIF
A description is not available for this item.
MPIF METALLURGY - POWDER METALLURGY SCIENCE
MPIF
A description is not available for this item.
MPIF METALLOGRAPHIC ATLAS - METALLOGRAPHIC ATLAS OF POWDER METALLURGY
MPIF
A description is not available for this item.
MBMA METAL BUILDING MNL - METAL BUILDING SYSTEMS MANUAL
MBMA
A description is not available for this item.
ASTM E1561-26 - Standard Practice for Analysis of Strain Gage Rosette Data
May 1, 2026 - ASTM International

This practice defines a reference axis for each of the two principal types of rosette configurations and the equations used for three-element strain gage rosette data analysis. The primary uses of this analysis procedure are to determine the directions and magnitudes of the principal surface...

ASTM D6846-02(2026) - Standard Practice for Preparing Prints of Paste Printing Inks with a Printing Gage
June 1, 2026 - ASTM International

1.1 This practice covers the procedure for preparing laboratory prints of paste inks using a printing gage in conjunction with a flat-bed proof press. 1.2 This practice is applicable to the preparation of solid-area prints by direct letterpress or by dry offset on a flat substrate such as...

ASTM D4414-25 - Standard Practice for Measurement of Wet Film Thickness by Notch Gages
July 1, 2025 - ASTM International

1.1 This practice describes the use of thin rigid metal notched gages, also called step or comb gages, in the measurement of wet film thickness of organic coatings, such as paint, varnish, and lacquer. 1.2 Notched gage measurements are neither accurate nor sensitive, but...

PPP-C-96 - CANS, METAL, 28 GAGE AND LIGHTER
December 31, 1992 - NPFC

This specification and appendix thereto cover the requirements for new metal cans made of 28 gage and lighter sheet metal plate, and DOT 2P and 2Q metal containers suitable for packaging and packing items for shipment and storage and the packaging, packing, and marking...

JIS METAL SURFACE HDBK - Metal Surface Treatment Handbook
January 1, 2020 - JSA
A description is not available for this item.
A-A-888 - CAN, METAL, 28 GAGE & LIGHTER
NPFC
A description is not available for this item.
JIS METAL ANALYSIS I HDBK - JIS Metal Analysis I - Ferrous Handbook
January 1, 2019 - JSA
A description is not available for this item.
JIS METAL ANALYSIS II - JIS Metal Analysis II – Non-Ferrous Handbook
January 1, 2019 - JSA
A description is not available for this item.
ASTM C743-24 - Standard Test Method for Continuity of Porcelain Enamel Coatings
May 1, 2024 - ASTM International

1.1 Porcelain enamel coatings are applied to metals to provide protection from corrosion as well as to enhance their appearance. This test method permits the easy detection of discontinuities and areas of light coverage, not readily seen by visual inspection, which limit the protection to...

ASTM A123/A123M-24 - Standard Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel Products
May 1, 2024 - ASTM International

1.1 This specification covers the requirements for zinc coating (galvanizing) by the hot-dip process on iron and steel products made from rolled pressed and forged shapes, castings, plates, bars, and strips. 1.2 This specification covers both unfabricated products and fabricated products, for...

Advertisement