1.1 These test methods cover the determination of the electrical conductivity of aviation and distillate fuels with and without a static dissipator additive. The test methods normally give a measurement of the conductivity when the fuel is uncharged, that is, electrically at rest (known as the rest...
1.1 This test method covers procedures for testing the durability of preassembled, permanently sealed vacuum insulating glass (VIG) units. 1.2 This test method is applicable only to VIG units that are constructed with flat glass lites (glass panes). 1.3 This test method is applicable to units made...
1.1 This practice covers a means of measuring the amount of heat transfer quantitatively through a material or system. 1.2 This practice is similar to the Heat Flow Meter System of Test Method C518, but modified to accommodate small test samples of higher thermal conductance. 1.3 The values...
1.1 This test method covers a method for the measurement of selected vulcanization characteristics of rubber compounds using unsealed and sealed torsion shear cure meters. The two types of instruments may not give the same results. Note 1: An alternative method for the measurement of...
4.1 Laboratory proofing of inks is necessary to establish a reproducible prediction of print appearance and performance properties, most of which are highly sensitive to ink film thickness. The apparatus described in this practice has found wide use for routine control proofing because it provides...
3.1 Definitions in this standard are to be regarded as the correct ones for terms found in other ASTM standards of Committee D18. Certain terms may be found in more than one standard issued under the jurisdiction of this committee and many of these terms have been placed in this standard. 3.2 Terms...
1.1 This practice covers minimum requirements for the design and manufacture of Electric Engines for light sport aircraft, VFR use. The Electric Propulsion System (EPS) shall as a minimum consist of the electric engine, associated controllers, disconnects and wiring, and EPS monitoring gauges and...
1.1 This specification defines general specifications for heat meters. Heat meters are instruments that measure heat in heat exchange circuits in which energy is absorbed (cooling) or given up (heating) by a flowing liquid. 1.2 For this specification, the necessary elements of a heat...
1.1 This test method covers the use of the oscillating disk cure meter for determining selected vulcanization characteristics of vulcanizable rubber compounds. 1.2 ISO 3417 is very similar to this test method. It has minor technical differences that are not considered to be significant. 1.3...
1.1 These test methods cover determination of the fineness of hydraulic cement, using the Blaine air-permeability apparatus, in terms of the specific surface expressed as total surface area in square centimeters per gram, or square meters per kilogram, of cement. Two test methods are given:...
1.1 This test method is used for evaluating how gloves affect an individual wearer's ability to grip onto a hard surface object. 1.1.1 This test method establishes procedures for measuring the maximum torque that can be attained by an individual's bare hand as compared to the maximum torque that is...
1.1 This practice covers minimum requirements for the design and manufacture of Electric Propulsion Units (EPU) for light sport aircraft, VFR use. The EPU shall as a minimum consist of the electric engine, associated controllers, disconnects and wiring, an Energy Storage Device (ESD) such as a...
1.1 This test method covers the sample preparation for cantilever beams and test methodology of thermoplastic pavement marking materials, similar to the "Izod Impact" method listed in Test Method D4812. 1.1.1 Some methods call for results in inch pound-force (in.·lbf) as opposed to the common foot...
4.1 This test method covers the determination of the air content of freshly mixed concrete. It measures the air contained in the mortar fraction of the concrete, but is not affected by air that may be present inside porous aggregate particles. 4.1.1 Therefore, this is the appropriate test to...
1.1 These specifications cover the equipment making up the temporary grounding system used on de-energized electric power lines, electric supply stations, and equipment. 1.2 It is common practice for the users of protective grounding equipment to prepare complete instructions and regulations to...
1.1 This test method covers a measurement of the wet retroreflective (RL-2) properties of horizontal pavement marking materials, such as traffic stripes and road surface symbols. A standardized method utilizing a standardized continuous wetting device and a portable retroreflectometer is described...
1.1 This practice provides information on apparatus, safety, pre-test preparation, and procedures for conducting field tests of polyamide-12 (PA12) pressure piping systems after installation using a non-flammable and non-toxic gaseous testing media (for example, air, nitrogen, carbon dioxide), and...
1.1 This practice provides information on apparatus, safety, pre-test preparation and procedures for conducting field tests of polyethylene pressure piping systems after installation using a non-flammable and non-toxic gaseous testing media, (for example, air, nitrogen, carbon dioxide), and...
5.1 The apparent density is an important measure of a material characteristic of the powder that is useful to the powder producers and powder users in determining quality and lot to lot consistency. 5.2 This test method is applicable to free-flowing and non-free-flowing metal powders, lubricated...
Narrow Your Results