5.1 Fracture mirror size analysis is a powerful tool for analyzing glass and ceramic fractures. Fracture mirrors are tell-tale fractographic markings in brittle materials that surround a fracture origin as discussed in Practices C1256 and C1322. Fig. 1 shows a schematic with key features identified...
4.1 This practice details a fiber training program that identifies the information and guidelines necessary for preparing a trainee to become a qualified FSP. The trainee is under the direct supervision of a qualified FSP throughout their training. Upon successful completion of the program, a...
1.1 The primary objective of metallographic examinations is to reveal the constituents and structure of metals and their alloys by means of a light optical or scanning electron microscope. In special cases, the objective of the examination may require the development of less detail than in...
This practices covers the detecting susceptibility to intergranular attack in ferritic stainless steel. Different method of preparing steel test specimens are presented. Four practices, including Practice W, X, Y, and Z, are used for determining susceptibility to intergranular attack in ferritic...
1.1 This test method covers the determination of residual stresses in a transparent glass matrix by means of a polarizing microscope using null or retardation compensation procedures. 1.2 Such residual stress determinations are of importance in evaluating the nature and degree of residual...
4.1 Addressing consensus standards with inter-laboratory studies (ILS) and methods specific to an organization. Test methods need to be validated in many cases, in order to be able to rely on the results. This has to be done at the organization performing the tests but is also performed in the...
1.1 The primary objective of metallographic examinations is to reveal the constituents and structure of metals and their alloys by means of a light optical or scanning electron microscope. In special cases, the objective of the examination may require the development of less detail than in...
5.1 The primary purpose of the PMA test is to determine the presence of mechanical damage, wear through, and other gross defects in the coating. Most metallic coatings are intended to be protective, and the presence of gross defects indicates a serious reduction of such protection. 5.2 The...
This practice outlines the standard procedures for performing petrographic examination of hardened concrete samples. The samples examined may be taken from concrete constructions, that is, all sorts of objects, units, or structures that have been built of hydraulic cement concrete. They may also be...
1.1 This guide provides information for the examination of hardened concrete using scanning electron microscopy (SEM) combined with energy-dispersive X-ray spectroscopy (EDX or EDS). Since the 1960s, SEM has been used for the examination of concrete and has proved to be an insightful tool for the...
1.1 This test method covers measurement of the local thickness of metal and oxide coatings by the microscopical examination of cross sections using an optical microscope. 1.2 Under good conditions, when using an optical microscope, the method is capable of giving an absolute measuring...
5.1 This test method provides a relatively simple and reliable microscopical means of measuring the phase abundance of portland cement clinker (Note 1). Microscopical point counting provides a direct measure of the clinker phase composition in contrast to the calculated Bogue phase composition...
1.1 This guidance document has been developed to facilitate the collection of microscopy images with an epifluorescence microscope that allows quantitative fluorescence measurements to be extracted from the images. The document is tailored to cell biologists that often use fluorescent...
4.1 From a quality risk management perspective (ICH Q9), extraneous solid and insoluble particulate matter in a final parenteral drug product is a potential hazard that may cause harm to the patient receiving the drug product in addition to potentially reducing drug product quality, efficacy, and...
4.1 The presence of extraneous solid and insoluble particulate matter in a final parenteral drug product is a potential hazard that may cause harm to the patient receiving the drug product in addition to potentially reducing drug product quality, efficacy, and availability. 4.2 This guide provides...
1.1 This practice provides a reproducible means by which one aspect of the performance of a scanning electron microscope (SEM) may be characterized. The resolution of an SEM depends on many factors, some of which are electron beam voltage and current, lens aberrations, contrast in the...
1.1 This test method, provided the limitations are understood, covers a procedure for both the enumeration and measurement of size distribution of many cell types. The instrumentation allows for user-selectable cell size settings and is applicable to a wide range of cell types. The method works...
5.1 For advanced ceramics, Vickers indenters are used to create indentations whose surface-projected diagonals are measured with optical microscopes. The Vickers indenter creates a square impression from which two surface-projected diagonal lengths are measured. Vickers hardness is...
5.1 Blocks or briquets of coke prepared in accordance with the laboratory procedures of this practice will have flat, scratch-free surfaces suitable for examination with a microscope using reflected light illumination. The polished surface of the blocks or briquets prepared using this...
1.1 This guide outlines various methods which may be followed in the photography of metals and materials with the reflected-light microscope. Methods are included for preparation of prints and transparencies in black-and-white and in color, using both direct rapid and wet processes. 1.2...
Narrow Your Results