loading
ASTM C1678-21(2026) - Standard Practice for Fractographic Analysis of Fracture Mirror Sizes in Ceramics and Glasses
June 1, 2026 - ASTM International

5.1 Fracture mirror size analysis is a powerful tool for analyzing glass and ceramic fractures. Fracture mirrors are tell-tale fractographic markings in brittle materials that surround a fracture origin as discussed in Practices C1256 and C1322. Fig. 1 shows a schematic with key features identified...

ASTM E3405-26 - Standard Practice for Forensic Fiber Training Program
March 1, 2026 - ASTM International

4.1 This practice details a fiber training program that identifies the information and guidelines necessary for preparing a trainee to become a qualified FSP. The trainee is under the direct supervision of a qualified FSP throughout their training. Upon successful completion of the program, a...

ASTM E3-26 - Standard Guide for Preparation of Metallographic Specimens
February 15, 2026 - ASTM International

1.1 The primary objective of metallographic examinations is to reveal the constituents and structure of metals and their alloys by means of a light optical or scanning electron microscope. In special cases, the objective of the examination may require the development of less detail than in...

ASTM A763-15(2025) - Standard Practices for Detecting Susceptibility to Intergranular Attack in Ferritic Stainless Steels
September 1, 2025 - ASTM International

This practices covers the detecting susceptibility to intergranular attack in ferritic stainless steel. Different method of preparing steel test specimens are presented. Four practices, including Practice W, X, Y, and Z, are used for determining susceptibility to intergranular attack in ferritic...

ASTM C978-04(2025) - Standard Test Method for Photoelastic Determination of Residual Stress in a Transparent Glass Matrix Using a Polarizing Microscope and Optical Retardation Compensation Procedures
July 1, 2025 - ASTM International

1.1 This test method covers the determination of residual stresses in a transparent glass matrix by means of a polarizing microscope using null or retardation compensation procedures. 1.2 Such residual stress determinations are of importance in evaluating the nature and degree of residual...

ASTM F3263-17(2025) - Standard Guide for Packaging Test Method Validation
October 1, 2025 - ASTM International

4.1 Addressing consensus standards with inter-laboratory studies (ILS) and methods specific to an organization. Test methods need to be validated in many cases, in order to be able to rely on the results. This has to be done at the organization performing the tests but is also performed in the...

ASTM E3-11(2025) - Standard Guide for Preparation of Metallographic Specimens
August 1, 2025 - ASTM International

1.1 The primary objective of metallographic examinations is to reveal the constituents and structure of metals and their alloys by means of a light optical or scanning electron microscope. In special cases, the objective of the examination may require the development of less detail than in...

ASTM B877-25 - Standard Test Method for Gross Defects and Mechanical Damage in Metallic Coatings by the Phosphomolybdic Acid (PMA) Method
July 1, 2025 - ASTM International

5.1 The primary purpose of the PMA test is to determine the presence of mechanical damage, wear through, and other gross defects in the coating. Most metallic coatings are intended to be protective, and the presence of gross defects indicates a serious reduction of such protection. 5.2 The...

ASTM C856/C856M-25 - Standard Practice for Petrographic Examination of Hardened Concrete
February 1, 2025 - ASTM International

This practice outlines the standard procedures for performing petrographic examination of hardened concrete samples. The samples examined may be taken from concrete constructions, that is, all sorts of objects, units, or structures that have been built of hydraulic cement concrete. They may also be...

ASTM C1723-25 - Standard Guide for Examination of Hardened Concrete Using Scanning Electron Microscopy
April 1, 2025 - ASTM International

1.1 This guide provides information for the examination of hardened concrete using scanning electron microscopy (SEM) combined with energy-dispersive X-ray spectroscopy (EDX or EDS). Since the 1960s, SEM has been used for the examination of concrete and has proved to be an insightful tool for the...

ASTM B487-24 - Standard Test Method for Measurement of Metal and Oxide Coating Thickness by Microscopical Examination of Cross Section
November 1, 2024 - ASTM International

1.1 This test method covers measurement of the local thickness of metal and oxide coatings by the microscopical examination of cross sections using an optical microscope. 1.2 Under good conditions, when using an optical microscope, the method is capable of giving an absolute measuring...

ASTM C1356-24 - Standard Test Method for Quantitative Determination of Phases in Portland Cement Clinker by Microscopical Point-Count Procedure
December 1, 2024 - ASTM International

5.1 This test method provides a relatively simple and reliable microscopical means of measuring the phase abundance of portland cement clinker (Note 1). Microscopical point counting provides a direct measure of the clinker phase composition in contrast to the calculated Bogue phase composition...

ASTM F3294-18(2024) - Standard Guide for Performing Quantitative Fluorescence Intensity Measurements in Cell-based Assays with Widefield Epifluorescence Microscopy
October 1, 2024 - ASTM International

1.1 This guidance document has been developed to facilitate the collection of microscopy images with an epifluorescence microscope that allows quantitative fluorescence measurements to be extracted from the images. The document is tailored to cell biologists that often use fluorescent...

ASTM E3411-24 - Standard Practice for Validation of Automated Membrane Microscopy Test Methods for the Counting and Sizing of Particulate Matter Present in Parenteral Pharmaceutical Manufacturing Processes and Final Drug Products
November 1, 2024 - ASTM International

4.1 From a quality risk management perspective (ICH Q9), extraneous solid and insoluble particulate matter in a final parenteral drug product is a potential hazard that may cause harm to the patient receiving the drug product in addition to potentially reducing drug product quality, efficacy, and...

ASTM E3425-24 - Standard Guide for Development of Automated Membrane Microscopy Test Methods for the Counting and Sizing of Particulate Matter Present in Parenteral Pharmaceutical Manufacturing Processes and Final Drug Products
November 1, 2024 - ASTM International

4.1 The presence of extraneous solid and insoluble particulate matter in a final parenteral drug product is a potential hazard that may cause harm to the patient receiving the drug product in addition to potentially reducing drug product quality, efficacy, and availability. 4.2 This guide provides...

ASTM E986-04(2024) - Standard Practice for Scanning Electron Microscope Beam Size Characterization
April 1, 2024 - ASTM International

1.1 This practice provides a reproducible means by which one aspect of the performance of a scanning electron microscope (SEM) may be characterized. The resolution of an SEM depends on many factors, some of which are electron beam voltage and current, lens aberrations, contrast in the...

ASTM F2149-24 - Standard Test Method for Automated Analyses of Cells—the Electrical Sensing Zone Method of Enumerating and Sizing Single Cell Suspensions
December 1, 2024 - ASTM International

1.1 This test method, provided the limitations are understood, covers a procedure for both the enumeration and measurement of size distribution of many cell types. The instrumentation allows for user-selectable cell size settings and is applicable to a wide range of cell types. The method works...

ASTM C1327-15(2024) - Standard Test Method for Vickers Indentation Hardness of Advanced Ceramics
September 1, 2024 - ASTM International

5.1 For advanced ceramics, Vickers indenters are used to create indentations whose surface-projected diagonals are measured with optical microscopes. The Vickers indenter creates a square impression from which two surface-projected diagonal lengths are measured. Vickers hardness is...

ASTM D3997/D3997M-24 - Standard Practice for Preparing Coke Samples for Microscopical Analysis by Reflected Light
July 1, 2024 - ASTM International

5.1 Blocks or briquets of coke prepared in accordance with the laboratory procedures of this practice will have flat, scratch-free surfaces suitable for examination with a microscope using reflected light illumination. The polished surface of the blocks or briquets prepared using this...

ASTM E883-11(2024) - Standard Guide for Reflected-Light Photomicrography
April 1, 2024 - ASTM International

1.1 This guide outlines various methods which may be followed in the photography of metals and materials with the reflected-light microscope. Methods are included for preparation of prints and transparencies in black-and-white and in color, using both direct rapid and wet processes. 1.2...

Advertisement