loading
ASTM D7274-26 - Standard Test Method for Mineral Stabilizer Content of Bituminous Geomembranes
April 1, 2026 - ASTM International

4.1 Bituminous geomembranes, whether made from oxidized or polymer-modified bitumen, may contain a significant amount of mineral stabilizer. The amount of mineral stabilizer used in a bituminous geomembrane has an effect on several physical properties, including but not limited to...

ASTM C1254-26 - Standard Test Method for Determination of Uranium in Mineral Acids by X-Ray Fluorescence
July 1, 2026 - ASTM International

1.1 This test method covers the steps necessary for the preparation and analysis of uranium in mineral acid solutions by X-ray fluorescence (XRF). 1.2 This test method is valid for those solutions containing uranium with mass concentrations of 0.05?g/L to 20?g/L as presented to the...

ASTM D6583-13(2026) - Standard Test Method for Porosity of Paint Film by Mineral Oil Absorption
June 1, 2026 - ASTM International

1.1 This test method is applicable to air-dry architectural coatings of any type, both solvent and water-borne, and of any color, dark as well as light. It cannot be used with films that are dissolved or excessively softened by mineral oil, but practical examples of such films will be...

ASTM C129-26 - Standard Specification for Dry-Cast Nonloadbearing Concrete Masonry Units
July 15, 2026 - ASTM International

1.1 This specification covers dry-cast hollow and solid nonloadbearing concrete masonry units machine-made from hydraulic cement, water, and suitable mineral aggregates with or without the inclusion of other materials. These units are intended for use in nonloadbearing partitions, but under...

ASTM D5350-95(2026) - Standard Test Method for Determination of Organically Combined Sulfuric Anhydride by Titration, Test Method A
July 1, 2026 - ASTM International

1.1 This test method covers the determination of the organically combined sulfuric anhydride existing in a sample of sulfated oil by boiling the sample with sulfuric acid and determining the acidity of the reaction mixture. This test method is applicable only to oils that split off their combined...

ASTM C1936-26 - Standard Test Method for Corrosiveness of Mineral-Fiber or Cellulosic-Fiber Insulation by Comparison to Control
March 1, 2026 - ASTM International

1.1 This method provides a qualitative measure of the corrosiveness of mineral-fiber or cellulose fiber insulation by comparison to a control. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of...

ASTM C547-25 - Standard Specification for Mineral Fiber Pipe Insulation
December 1, 2025 - ASTM International

1.1 This specification covers mineral fiber insulation produced to form hollow cylinders for standard pipe and tubing sizes. Use mineral fiber pipe insulation that has been either molded or precision v-grooved, with one or more walls split longitudinally for use on pipe temperatures...

ASTM C1623-26 - Standard Specification for Solid Dry-Cast Manufactured Concrete Masonry Lintels
June 1, 2026 - ASTM International

1.1 This specification covers dry-cast concrete masonry lintels (beams) that are solid in cross-section, are reinforced for flexure, and are machine-made from hydraulic cement, water, and suitable mineral aggregates with or without the inclusion of other materials. These lintels are suitable...

ASTM D3279-19(2026) - Standard Test Method for n-Heptane Insolubles
June 1, 2026 - ASTM International

1.1 This test method covers determination of the mass percent of asphaltenes as defined by insolubility in normal-heptane solvent. It is applicable to all solid and semi-solid petroleum asphalts containing little or no mineral matter, to gas oils, to heavy fuel oils, and to crude petroleum...

ASTM D8671-26 - Standard Guide for Determination of Silica and Alumina Molar Ratio in Zeolites by Inductively Coupled Plasma Optical Emission Spectroscopy
June 1, 2026 - ASTM International

1.1 This guide covers the analysis of silicon and aluminum in zeolite by Inductive Coupled Plasma Optical Emission Spectroscopy (ICP-OES). Zeolite samples in powdered form are ultrasonicated with mineral acid mixture (hydrochloric acid and hydrofluoric acid). Zeolite silica and alumina molar...

ASTM E3536/E3536M-26 - Standard Specification for Compacted Mineral-Insulated, Niobium-Sheathed, High Temperature Irradiation Resistant Thermocouples
April 1, 2026 - ASTM International

1.1 This specification covers dimensional and material requirements for compacted, mineral-insulated, niobium-sheathed, high temperature, irradiation resistant thermocouples (HTIR-TC) with one HTIR-TC thermoelement pair. These types of thermocouples are suitable for high neutron fluence, up...

ASTM D6871-26 - Standard Specification for Natural (Vegetable Oil) Ester Fluids Used in Electrical Apparatus
June 1, 2026 - ASTM International

1.1 This specification covers a high fire point natural vegetable oil ester insulating fluid for use as a dielectric and cooling medium in new and existing power and distribution electrical apparatus such as transformers and attendant equipment. 1.2 Natural vegetable oil ester insulating fluid...

ASTM D8126-26 - Standard Test Method for Efficient Basicity Determination by Potentiometric Hydrochloric Acid Titration
June 1, 2026 - ASTM International

1.1 This test method covers a procedure for the determination of the efficient basicity (EBas) in new marine cylinder lubricants that lubricate the upper part, that is, piston-ring-cylinder area, of two-stroke marine engines. 1.2 This test method has been developed for marine cylinder lubricants,...

ASTM C1014-26 - Standard Specification for Spray-Applied Mineral Fiber Thermal and Sound Absorbing Insulation
January 1, 2026 - ASTM International

This specification covers the composition and the physical properties of spray-applied mineral fiber thermal and sound absorbing insulation. These mineral fibers shall be pneumatically conveyed to a spray nozzle where they are mixed with water. These mineral fibers shall have a...

ASTM C478/C478M-26 - Standard Specification for Circular Precast Reinforced Concrete Manhole Sections
May 15, 2026 - ASTM International

This specification covers the manufacture and purchase requirements of products used for the assembly and construction of circular vertical precast reinforced concrete manholes and structures used in sewer and water works. Reinforced concrete shall consist of cementitious materials, mineral...

ASTM D2172/D2172M-26 - Standard Test Methods for Quantitative Extraction of Asphalt Binder from Asphalt Mixtures
May 1, 2026 - ASTM International

4.1 All of these test methods can be used for quantitative determinations of asphalt binder in asphalt mixtures and pavement samples for specification acceptance, service evaluation, control, and research. Each method prescribes the solvent or solvents and any other reagents that can be used in the...

ASTM D4464-26 - Standard Test Method for Particle Size Distribution of Catalytic Materials by Laser Light Scattering
April 1, 2026 - ASTM International

5.1 It is important to recognize that the results obtained by this test method or any other method for particle size determination utilizing different physical principles may disagree. The results are strongly influenced by physical principles employed by each method of particle size analysis. The...

ASTM D2449-88(2026) - Standard Specification for Rubber Bales From Natural Sources—Limit on Coating
April 1, 2026 - ASTM International

This specification covers bale coatings on rubber bales made from natural sources. This is not applicable to natural rubbers packaged with plastic wrappers. Samples for testing should be carefully collected at random from the outside of the wrapper sheets from any three sides of the bale and...

ASTM C612-25 - Standard Specification for Mineral Fiber Block and Board Thermal Insulation
November 15, 2025 - ASTM International

This specification covers mineral fiber block and board thermal insulation. Mineral fiber board insulation covered by this specification shall be classified into types and categories; category 1 - no compressive resistance properties are required, category 2 - minimum compressive...

Advertisement