loading
ASTM C1678-21(2026) - Standard Practice for Fractographic Analysis of Fracture Mirror Sizes in Ceramics and Glasses
June 1, 2026 - ASTM International

1.1 This practice pertains to the analysis and interpretation of fracture mirror sizes in brittle materials. Fracture mirrors (Fig. 1) are telltale fractographic markings that surround a fracture origin in brittle materials. The fracture mirror size may be used with known...

ASTM D2029-26 - Standard Test Methods for Water Vapor Content of Electrical Insulating Gases by Measurement of Dew Point
January 1, 2026 - ASTM International

1.1 These test methods describe the determination of the water vapor content of electrical insulating gases by directly or indirectly measuring the dew point and calculating the water vapor content. 1.2 The following three test methods are provided: 1.2.1 Method A describes the automatic chilled...

ASTM E307-72(2025) - Standard Test Method for Normal Spectral Emittance at Elevated Temperatures
December 1, 2025 - ASTM International

5.1 The significant features are typified by a discussion of the limitations of the technique. With the description and arrangement given in the following portions of this test method, the instrument will record directly the normal spectral emittance of a specimen. However, the following conditions...

ASTM E423-71(2025) - Standard Test Method for Normal Spectral Emittance at Elevated Temperatures of Nonconducting Specimens
December 1, 2025 - ASTM International

5.1 The significant features are typified by a discussion of the limitations of the technique. With the description and arrangement given in the following portions of this test method, the instrument will record directly the normal spectral emittance of a specimen. However, the following conditions...

ASTM E289-25 - Standard Test Method for Linear Thermal Expansion of Rigid Solids with Interferometry
October 1, 2025 - ASTM International

5.1 Coefficients of linear expansion are required for design purposes and are used particularly to determine thermal stresses that can occur when a solid artifact composed of different materials may fail when it is subjected to a temperature excursion(s). 5.2 Many new composites are being produced...

ASTM D6836-25 - Standard Test Methods for Determination of the Soil Water Characteristic Curve
July 1, 2025 - ASTM International

1.1 These test methods cover the determination of Soil Water Characteristic Curves (SWCCs). SWCCs describe the relationship between suction and volumetric water content, gravimetric water content, or degree of water saturation. SWCCs are also referred to as soil water retention curves, soil water...

ASTM C1503-24 - Standard Specification for Silvered Flat Glass Mirror
February 1, 2024 - ASTM International

1.1 This specification covers the requirements for silvered flat glass mirrors of rectangular shape supplied as cut sizes, stock sheets, or as lehr ends and to which no further processing (such as edgework or other fabrication) has been done. 1.2 This specification covers the quality...

ASTM C1036-25 - Standard Specification for Flat Glass
February 1, 2025 - ASTM International

This specification covers the quality requirements of flat, transparent, clear, and tinted glass. This glass is intended to be used primarily for architectural glazing products including: coated glass, insulating glass units, laminated glass, mirrors, spandrel glass, or similar uses. The...

ASTM F688-25 - Standard Specification for Wrought Cobalt-35Nickel-20Chromium-10Molybdenum Alloy Plate, Sheet, and Foil for Surgical Implants (UNS R30035)
January 15, 2025 - ASTM International

This specification covers the requirements for wrought cobalt-35nickel-20chromium-10molybdenum alloy for use in the manufacture of surgical implants. The alloy shall be manufactured into plates, sheets, and foils in the annealed, cold-worked, or cold-worked and capability-aged condition. The plates...

ASTM C1322-25 - Standard Practice for Fractography and Characterization of Fracture Origins in Advanced Ceramics
January 1, 2025 - ASTM International

1.1 The objective of this practice is to provide an efficient and consistent methodology to locate and characterize fracture origins in advanced ceramics. It is applicable to advanced ceramics that are brittle; that is, fracture that takes place with little or no preceding plastic deformation. In...

ASTM F3718-24 - Standard Practice for Maintaining Oxidative Capacity of Test Solutions for Degradation Screening of Non-Absorbable Polymers
December 1, 2024 - ASTM International

4.1 This standard practice summarizes a method to maintain the oxidative capacity of test solutions, in line with the recommendations of ISO 10993-13. The approach outlined in this standard practice is applicable for ongoing monitoring and maintenance of hydrogen peroxide (H2O2) concentrations in...

ASTM C1322-15(2024) - Standard Practice for Fractography and Characterization of Fracture Origins in Advanced Ceramics
September 1, 2024 - ASTM International

1.1 The objective of this practice is to provide an efficient and consistent methodology to locate and characterize fracture origins in advanced ceramics. It is applicable to advanced ceramics that are brittle; that is, fracture that takes place with little or no preceding plastic deformation. In...

ASTM E81-96(2024) - Standard Test Method for Preparing Quantitative Pole Figures
April 1, 2024 - ASTM International

1.1 This test method covers the use of the X-ray diffractometer to prepare quantitative pole figures. 1.2 The test method consists of several experimental procedures. Some of the procedures (1-5)2 permit preparation of a complete pole figure. Others must be used in combination to produce a complete...

ASTM E3225-24 - Standard Practice for Performing Visual Examination of Containment Sumps
February 1, 2024 - ASTM International

5.1 All liquid and debris in a containment sump should be removed and managed properly. 5.2 Liquids introduced into a containment sump for testing purposes may come in contact with regulated substances that have leaked from the primary UST system. 5.2.1 Test liquids in contact with regulated...

ASTM C1661-23 - Standard Guide for Viewing Systems for Remotely Operated Facilities
October 1, 2023 - ASTM International

1.1 Intent: 1.1.1 This guide establishes the minimum requirements for viewing systems for remotely operated facilities, including hot cells (shielded cells), used for the processing and handling of nuclear and radioactive materials. The intent of this guide is to aid in the design, selection,...

ASTM G90-23 - Standard Practice for Performing Accelerated Outdoor Weathering of Materials Using Concentrated Natural Sunlight
July 1, 2023 - ASTM International

1.1 Linear Fresnel reflector concentrators using the sun as source are utilized in the accelerated outdoor exposure testing of materials. 1.2 This practice covers a procedure for performing accelerated outdoor exposure testing of materials using a linear Fresnel reflector, accelerated outdoor...

ASTM G213-17(2023) - Standard Guide for Evaluating Uncertainty in Calibration and Field Measurements of Broadband Irradiance with Pyranometers and Pyrheliometers
January 1, 2023 - ASTM International

5.1 The uncertainty in outdoor solar irradiance measurement has a significant impact on weathering and durability and the service lifetime of materials systems. Accurate solar irradiance measurement with known uncertainty will assist in determining the performance over time of component materials...

ASTM F1166-23 - Standard Practice for Human Engineering Design for Marine Systems, Equipment, and Facilities
January 1, 2023 - ASTM International

1.1 This practice provides ergonomic design criteria from a human-machine perspective for the design and construction of maritime vessels and structures and for equipment, systems, and subsystems contained therein, including vendor-purchased hardware and software. 1.1.1 The focus of these design...

UL 962 - Household and Commercial Furnishings
October 21, 2022 - ULSE

1.1 These requirements cover: a) Motor-operated furniture, such as motor-operated beds, chairs, audio/video motorized carts/stands and blood donor chairs as well as the motorized drives for these units; b) Electrified and non-electrified furniture; c) Non-seasonal electrical decorations such as...

ASTM C1678-21 - Standard Practice for Fractographic Analysis of Fracture Mirror Sizes in Ceramics and Glasses
July 1, 2021 - ASTM International

1.1 This practice pertains to the analysis and interpretation of fracture mirror sizes in brittle materials. Fracture mirrors (Fig. 1) are telltale fractographic markings that surround a fracture origin in brittle materials. The fracture mirror size may be used with known...

Advertisement