loading
ASTM D4867/D4867M-26 - Standard Test Method for Effect of Moisture on Asphalt Mixtures
May 1, 2026 - ASTM International

5.1 This test method can be used to test asphalt mixtures in conjunction with mixture design testing to determine the potential for moisture damage, to determine whether or not an antistripping additive is effective, and to determine what dosage of an additive is needed to maximize the...

ASTM D8638-26 - Standard Test Method for Single-Stage Total Moisture in Coke
April 1, 2026 - ASTM International

1.1 This test method covers single-stage procedures for the determination of total moisture in metallurgical coke. 1.2 Units-The values stated in SI units are to be regarded as the standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to...

ASTM D1042-26 - Standard Test Method for Linear Dimensional Changes of Plastics Caused by Exposure to Heat and Moisture
July 1, 2026 - ASTM International

4.1 This test method is intended only as a convenient test method for measurement of linear dimensional changes in plastics subjected to defined conditions of test as outlined in Sections 7 and 8.

ASTM D4933-16(2026) - Standard Guide for Moisture Conditioning of Wood and Wood-Based Materials
April 1, 2026 - ASTM International

4.1 Many physical and mechanical properties of wood and wood-based materials change in response to the environmental equilibrium moisture content, and any comparison of these properties must take moisture content into account. A consistent base for comparison among different test...

ASTM D6542-05(2026) - Standard Practice for Tonnage Calculation of Coal in a Stockpile
July 15, 2026 - ASTM International

1.1 This practice is used to calculate the mass (commonly expressed in tons) of coal in a storage pile using the volume of the stockpile by Test Method D6172/D6172M and the density of the coal determined by Test Method D6347/D6347M. 1.2 This practice is applicable to all ranks of coal. 1.3 The user...

ASTM D6714-16(2026) - Standard Test Method for Chromic Oxide in Ashed Wet Blue (Perchloric Acid Oxidation)
July 1, 2026 - ASTM International

1.1 This test method covers the determination of chromic oxide in Wet Blue that has been partly or completely tanned with chromium compounds. In general the samples will contain chromium content between 1?% and 5?%, calculated as chromic oxide expressed upon a dry basis otherwise referred to as...

ASTM E534-26 - Standard Test Methods for Chemical Analysis of Sodium Chloride
July 1, 2026 - ASTM International

1.1 These test methods cover the chemical analyses usually required for sodium chloride. 1.2 The analytical procedures appear in the following sections: Section Sample Preparation ?5 to? 9 Moisture 10 to 17 Water Insolubles 18 to 26 Calcium and Magnesium 27 to 34 Sulfate 35 to 42 Reporting...

ASTM D7967-21(2026) - Standard Test Method for Analysis of Chrome Content (as Cr2O3) in Wet Blue using Atomic Absorption or ICP
July 1, 2026 - ASTM International

1.1 This test method covers the Atomic Absorption procedure, using nitrous oxide-acetylene flame, air-acetylene flame or ICP (Inductively coupled plasma) to analyze the chrome content of Wet Blue (and leather) on a moisture-free basis. 1.2 The values stated in SI units are to be regarded as...

ASTM E1868-26 - Standard Test Methods for Loss-On-Drying by Thermogravimetry
July 1, 2026 - ASTM International

5.1 These test methods are used to estimate the amount of volatile materials present in a material. 5.2 These test methods are useful for design purposes, service evaluation, regulatory statutes, manufacturing control, quality control, specification acceptance, development, and research. 5.3 The...

ASTM C70-26 - Standard Test Method for Surface Moisture in Fine Aggregate
February 1, 2026 - ASTM International

1.1 This test method covers field determination of the amount of surface moisture in fine aggregate by displacement in water. 1.2 The values stated in SI units are to be regarded as the standard. No other units of measurement are included in this standard. 1.3 This standard does not purport...

ASTM F2471-26 - Standard Practice for Installation of Thick Poured Lightweight Cellular Concrete Underlayments and Preparation of the Surface to Receive Resilient Flooring
June 1, 2026 - ASTM International

1.1 This practice covers the installation and preparation of the thick poured lightweight cellular concrete underlayments over wood structural panel subfloors in commercial structures or over concrete floors in commercial structures and the preparation of the thick poured lightweight cellular...

ASTM C424-26 - Standard Test Method for Crazing Resistance of Fired Glazed Whitewares by Autoclave Treatment
June 1, 2026 - ASTM International

2.1 This test method is particularly useful for porous materials that can exhibit moisture expansion. 2.2 This test method is a primary test method that is suitable for use in specifications, quality control, and research and development. It can also serve as a referee test method in...

ASTM C1933/C1933M-26 - Standard Test Methods for Floor Patching and Skim Coating Compounds Containing Hydraulic Cements
June 1, 2026 - ASTM International

4.1 The test methods in this standard are used to evaluate properties such as setting time, compressive strength, flexural strength, moisture resistance and bonding strength of floor patching compounds. 4.2 Tests are conducted under standardized conditions for comparative purposes and...

ASTM E3006-20(2026) - Standard Practice for Ultraviolet Conditioning of Photovoltaic Modules or Mini-Modules Using a Fluorescent Ultraviolet (UV) Lamp Apparatus
June 1, 2026 - ASTM International

5.1 Photovoltaic modules and components must be resistant to prolonged exposure to solar radiation, moisture, and heat. Degradation of polymeric components, delamination at the encapsulant and other interfaces, and moisture ingress are among the degradation modes known to decrease the...

ASTM C311/C311M-26 - Standard Test Methods for Sampling and Testing Coal Ash or Natural Pozzolans for Use in Concrete
June 15, 2026 - ASTM International

1.1 These test methods cover procedures for sampling and testing coal ash and raw or calcined pozzolans for use in concrete. 1.2 The procedures appear in the following order: Sections Sampling 7 CHEMICAL ANALYSIS Reagents and apparatus 10 Moisture content 11 and 12 Loss on ignition 13 and 14...

ASTM C216-26a - Standard Specification for Facing Brick (Solid Masonry Units Made from Clay or Shale)
June 1, 2026 - ASTM International

This specification covers brick intended for use in masonry and supplying structural or facing components, or both, to the structure. Bricks shall be classified according to their resistance to damage by freezing when saturated at a moisture content: Grade SW and Grade MW. The facing bricks...

ASTM D4069-95(2026)e1 - Standard Specification for Impregnated Activated Carbon Used to Remove Gaseous Radio-Iodines from Gas Streams
June 1, 2026 - ASTM International

This standard covers the specifications for physical properties and performance requirements of virgin impregnated activated carbon to be used for the removal of gaseous radioiodine species from gas streams. The activated carbon furnished under this specification shall be virgin material. Each...

ASTM D521-26 - Standard Test Methods for Chemical Analysis of Zinc Dust (Metallic Zinc Powder)
June 1, 2026 - ASTM International

1.1 These test methods cover procedures for the chemical analysis of metallic zinc powder in the form commercially known as zinc dust for use as a pigment in paints. 1.2 The analytical procedures appear in the following order: Sections Moisture and Other Volatile Matter 7 Coarse Particles 8...

ASTM F3013-13(2026) - Standard Test Method for Density of Topsoil and Blended Soils In-place by the Core Displacement Method
June 1, 2026 - ASTM International

1.1 This test method may be used to determine the undisturbed (in-situ) in-place bulk-density, moisture content and unit weight of topsoil and blended soil growing mediums using the Core Displacement Method. 1.2 This test method is applicable for soils without appreciable amounts of rock or...

ASTM D5577-26 - Standard Guide for Techniques to Separate and Identify Contaminants in Recycled Plastics
May 15, 2026 - ASTM International

5.1 Recycled plastic materials may contain incompatible plastic or other undesirable contaminants that could affect the processing or quality, or both, of the plastic prepared for reuse. Techniques to separate and identify incompatible plastics, moisture, chemicals, or original product...

Advertisement