5.1 Before proceeding with this test method, refer to the material specification for the material being tested. Any test specimen preparation, conditioning, dimensions and testing parameters required by the materials specification shall take precedence over those required by this test method. Table...
5.1 During preconstruction and construction evaluations, use of these test methods establishes specific and overall performance characteristics for the mortar system. 5.2 Preconstruction testing of mortars prebatched by weight provides information for the selection of the individual mortar system...
1.1 This classification covers rigid Poly(Vinyl Chloride)(PVC), Chlorinated Poly(Vinyl Chloride)(CPVC), copolymers, blends and alloys, and composite materials derived from recyclate from extruded, molded or calendared forms or operations and composed of polyvinyl chloride, chlorinated...
1.1 This practice covers the sorting of natural rubber bales of TSR10 or TSR20 in the factory according to their predicted processing performance based on differences in viscoelastic properties. 1.2 This practice determines which bales should be used in factory compounds which benefit from...
5.1 Before proceeding with these test methods, refer to the specification of the material being tested. Any test specimen preparation, conditioning, dimensions, and testing parameters covered in the materials specification shall take precedence over those mentioned in these test methods. If there...
1.1 This specification covers the evaluation of adhesives suitable for the bonding of oriented strand board (OSB) to rigid cellular polystyrene insulation core materials for general structure use. 1.2 The requirements of the structural insulated panel (SIP) adhesive are based on the...
1.1 This test method covers procedures for the preparation, curing, transporting and testing of cylindrical test specimens of controlled low strength material (CLSM) for the determination of compressive strength. 1.2 This test method covers CLSM materials that have a higher strength than the soil...
This specification covers a corrosion and heat-resistant nickel alloy in the form of metal injection molded (MIM) parts.
5.1 Nuclear grade graphite is a composite material made from petroleum or a coal-tar-based coke and a pitch binder. Manufacturing graphite is an iterative process of baking and pitch impregnation of a formed billet prior to final graphitization, which occurs at temperatures greater than...
5.1 Flexural properties as determined by this test method are especially useful for quality control and specification purposes. They include: 5.1.1 Flexural Stress (σf)-When a homogeneous elastic material is tested in flexure as a simple beam supported at two points and loaded at the midpoint, the...
1.1 This specification covers autoclaved aerated concrete (AAC), a cementitious product based on calcium silicate hydrates in which low density is attained by the inclusion of an agent resulting in macroscopic voids, and in which curing is carried out using high-pressure steam. 1.2 The raw...
1.1 These test methods cover the determination of the maximum dry unit weight of granular soils. A vibrating hammer is used to impart a surcharge and compactive effort to the soil specimen. Further, an optional calculation is presented to determine the approximate water content range for effective...
This classification system covers nylon injection and extrusion materials. Nylon materials are classified into groups according to their composition. Groups are further classified into classes and grades. Grades are identified by a single letter that indicates the reinforcement or filler used and...
5.1 The metallurgical properties of aluminum and its alloys are highly dependent on chemical composition. Precise and accurate analyses are essential to obtaining desired properties, meeting customer specifications, and minimizing scrap due to off-grade material. 5.2 This test method is applicable...
This specification covers three types of masonry cement for use where mortar for masonry is required. Masonry cement shall conform to the applicable physical property requirements prescribed. The masonry cement shall be sampled in accordance with practice C 183. The temperature and relative...
This specification covers rigid poly(vinyl chloride) (PVC) compounds and chlorinated poly(vinyl chloride) (CPVC) compounds for use in extruded or molded form like pipe and fitting applications. Classification requirements for identifying rigid PVC and CPVC shall be according to base...
1.1 These test methods are used to estimate the effect of exposure, under surface tensile strain conditions, either dynamic or static, in an atmosphere containing specified levels of ozone concentration, expressed as partial pressure (refer to Note 1), on vulcanized rubber, rubber compounds,...
5.1 During preconstruction and construction evaluations, use of these test methods establishes specific and overall performance characteristics for the mortar system. 5.2 Preconstruction testing of mortars prebatched by weight provides information for the selection of the individual mortar system...
5.1 Reported particle size measurement is a function of both the actual particle dimension and shape factor as well as the particular physical or chemical properties being measured. Caution is required when comparing data from instruments operating on different physical or chemical parameters or...
Narrow Your Results