The provisions of this code shall apply to the erection, installation, alteration, addition, repair, relocation, replacement, addition to, use or maintenance of solar energy, water heating, appliances intended for space heating or cooling, swimming pool heating, process heating, geothermal...
The provisions of this code shall apply to the erection, installation, alteration, repair, relocation, replacement, addition to, use, or maintenance of solar energy systems, including but not limited to equipment and appliances intended to utilize solar energy for space heating or cooling;...
USER GUIDE TO PRODUCT SPECIFICATIONS FOR ELECTRICAL BUILDING WIRE AND CABLE This Guide is published by the Building Wire and Cable Section of the National Electrical Manufacturers Association to assist users of commonly utilized electrical building wire and cable on the proper identification of U.S...
1.1 This practice covers the sorting of natural rubber bales of TSR10 or TSR20 in the factory according to their predicted processing performance based on differences in viscoelastic properties. 1.2 This practice determines which bales should be used in factory compounds which benefit from...
4.1 While end-use product performance and durability remain critical for functionality, the focus on recycling rigid PVC products or components at their end of life needs to be intensified. Participants in the value chain (for example, material scientists, product designers, procurement, and...
1.1 This general requirements specification covers a group of common requirements that, unless otherwise specified in the applicable product specification, apply to rolled structural steel bars, plates, shapes, and sheet piling covered by each of the following product specifications issued by ASTM:...
5.1 Before proceeding with these test methods, refer to the specification of the material being tested. Any test specimen preparation, conditioning, dimensions, and testing parameters covered in the materials specification shall take precedence over those mentioned in these test methods. If there...
1.1 This test method covers the determination of the tensile properties of thermosetting reinforced plastics using test specimens of uniform nominal width when tested under defined conditions of pretreatment, temperature, humidity, and testing-machine speed. Note 1: Experience with this test...
1.1 These test methods are used to determine the flexural properties of unreinforced and reinforced plastics, including high modulus composites and electrical insulating materials utilizing a three-point loading system to apply a load to a simply supported beam (specimen). The method is...
This specification deals with the general requirements that apply to rolled structural steel bars, plates, shapes, and sheet piling. The steel shall be made in an open-hearth, basic-oxygen, or electric-arc furnace followed by additional refining in a ladle metallurgy furnace, or secondary melting...
1.1 These test methods cover the determination of the maximum dry unit weight of granular soils. A vibrating hammer is used to impart a surcharge and compactive effort to the soil specimen. Further, an optional calculation is presented to determine the approximate water content range for...
4.1 Transfer molding is particularly suited to thermosetting materials of intermediate plasticity. Fixed molding parameters cannot be specified for each type of material. Molding compounds of the same type come in many different plasticities measured in accordance with Test Methods D3123 and D3795....
1.1 This test method describes a procedure that can be used in the field or in a laboratory to detect antigens indicative of microbial contamination in liquid fuels, including those blended with synthesized hydrocarbons or biofuels, with kinematic viscosities (at 40?°C) of =24?mm2s-1 (for...
This specification covers the standard requirements for lead and lead alloy strip, sheet, and plate products intended for use in chemical plants, sound attenuation, roofing, vibration dampening, flashing and weather stripping, waterproofing, and radiation shielding. The lead sheet, strip, or...
4.1 The methods by which sample materials are prepared and molded influence the mechanical properties of the specimen. Unlike injection molding, the objective of compression molding is to produce test specimens or sheets that are both homogeneous and isotropic. Specimens can be molded...
1.1 This practice describes surface preparations for plastic adherends, to be used prior to adhesive bonding of test specimens. It should be noted, however, that this practice specifies only the pretreating conditions of the plastic and does not cover the preparation of test specimens,...
Narrow Your Results