loading
ASTM D7989-26 - Standard Practice for Demonstrating Equivalent In-Plane Lateral Seismic Performance to Wood-Frame Shear Walls Sheathed with Wood Structural Panels
April 1, 2026 - ASTM International

5.1 This practice documents cyclic performance benchmarks for shear walls constructed with wood structural panel (WSP) sheathing attached to dimension lumber framing using common or galvanized box nails as defined in 3.2.8. 5.2 Procedures described in this practice provide a method to...

ASTM C844-26 - Standard Specification for Application of Gypsum Base to Receive Gypsum Veneer Plaster
May 1, 2026 - ASTM International

This specification covers the minimum requirements for, and methods of, application of gypsum veneer base for gypsum veneer plasters. Details of construction for a specific assembly to achieve the required fire resistance shall be obtained from reports of fire-resistance tests, engineering...

ASTM D1970/D1970M-25 - Standard Specification for Self-Adhering Polymer Modified Bituminous Sheet Materials Used as Steep Roofing Underlayment for Ice Dam Protection
December 1, 2025 - ASTM International

1.1 This specification covers polymer modified bituminous sheet materials intended for use as underlayment on roof eaves, or valleys, or both, to prevent leakage of shingle, tile, or metal roofs from water back-up due to ice dams. 1.2 These underlayment sheets have a sticky adhesive layer which is...

ASTM D1761-20(2025) - Standard Test Methods for Mechanical Fasteners in Wood and Wood-Based Materials
August 1, 2025 - ASTM International

1.1 These test methods provide a basic procedure for evaluating the withdrawal and lateral resistance of fasteners installed in wood and wood-based materials. Spikes are included as nails in this standard. 1.2 The tests also provide a basis for determining comparable performance of different...

ASTM C1063-25a - Standard Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-Based Plaster
November 1, 2025 - ASTM International

This specification covers the installation of lathing and furring to receive interior and exterior Portland cement-based plaster. The following materials shall be used: metal plaster bases-expanded metal lath and wire laths; accessories-steel, PVC plastic, zinc alloy, and cornerite;...

ASTM C840-25 - Standard Specification for Application and Finishing of Gypsum Board
November 1, 2025 - ASTM International

This specification covers requirements for the methods of application and finishing of gypsum board. Construction details for a specific assembly to achieve the required fire resistance shall be obtained from reports of fire-resistance tests, engineering evaluations, or listings from recognized...

ASTM C1063-25 - Standard Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-Based Plaster
October 15, 2025 - ASTM International

This specification covers the installation of lathing and furring to receive interior and exterior Portland cement-based plaster. The following materials shall be used: metal plaster bases-expanded metal lath and wire laths; accessories-steel, PVC plastic, zinc alloy, and cornerite;...

ASTM D3679-25 - Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding
July 1, 2025 - ASTM International

This specification establishes requirements and test methods for the materials, dimensions, warp, shrinkage, impact strength, expansion, appearance, and windload resistance of extruded single-wall siding manufactured from rigid (unplasticized) PVC compound. The siding shall be made of one or more...

ASTM A641/A641M-19(2025) - Standard Specification for Zinc-Coated (Galvanized) Carbon Steel Wire
April 1, 2025 - ASTM International

1.1 This specification covers soft, medium, and hard temper zinc-coated (galvanized) carbon steel wire in coils for general use. 1.2 The supplementary requirements of this specification cover zinc-coated weights [masses] for nails, staples, and wire from which nails and staples are...

ASTM C1355/C1355M-25 - Standard Specification for Glass Fiber Reinforced Gypsum Composites
April 1, 2025 - ASTM International

This specification covers glass fiber reinforced gypsum (GRG) composites suitable for producing GRG parts for non-loading bearings, thin sections, and ornamental shapes for architectural embellishment of interior building construction. Both the neat alpha gypsum cement and the resulting composite...

ASTM D143-25 - Standard Test Methods for Small Clear Specimens of Timber
April 15, 2025 - ASTM International

1.1 These test methods cover the determination of various strength and related properties of wood by testing small clear specimens. 1.1.1 These test methods represent procedures for evaluating the different mechanical and physical properties, controlling factors such as specimen size, moisture...

ASTM D5933-25 - Standard Specification for 258-in. and 4-in. Diameter Metal Shear Plates for Use in Wood Constructions
April 1, 2025 - ASTM International

This specification covers standardizing the dimensions and materials for the manufacture of steel or cast iron shear plates used in the fabrication of connections in wood constructions. This specification covers the two basic diameters of metal shear plates commonly used in North American timber...

ASTM D6117-24 - Standard Test Methods for Mechanical Fasteners in Plastic Lumber and Shapes
December 1, 2024 - ASTM International

6.1 The resistance of plastic lumber and shapes to direct withdrawal of nails, staples, or screws is a measure of its ability to hold or be held to an adjoining object by means of such fasteners. Factors that affect this withdrawal resistance include the physical and mechanical properties of...

ASTM C473-24 - Standard Test Methods for Physical Testing of Gypsum Panel Products
December 1, 2024 - ASTM International

1.1 These test methods cover the physical testing of gypsum panel products. 1.2 The test methods appear in the following order: Section Flexural Strength (Method A) ?7 Core, End and Edge Hardness (Method A) ?8 Nail Pull Resistance (Method A) ?9 Flexural Strength (Method B) 11 Core, End and...

ASTM C1063-24 - Standard Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-Based Plaster
December 1, 2024 - ASTM International

This specification covers the installation of lathing and furring to receive interior and exterior Portland cement-based plaster. The following materials shall be used: metal plaster bases-expanded metal lath and wire laths; accessories-steel, PVC plastic, zinc alloy, and cornerite;...

ASTM C840-24 - Standard Specification for Application and Finishing of Gypsum Board
November 1, 2024 - ASTM International

This specification covers requirements for the methods of application and finishing of gypsum board. Construction details for a specific assembly to achieve the required fire resistance shall be obtained from reports of fire-resistance tests, engineering evaluations, or listings from recognized...

ASTM C1396/C1396M-24 - Standard Specification for Gypsum Board
October 1, 2024 - ASTM International

This specification covers gypsum boards which include the following: gypsum wallboard for use on walls, ceilings, or partitions and that affords a surface suitable to receive decoration; predecorated gypsum board for use as the finished surfacing for walls, ceilings, or partitions; gypsum backing...

ASTM E580/E580M-24a - Standard Practice for Installation of Ceiling Suspension Systems for Acoustical Tile and Lay-in Panels in Areas Subject to Earthquake Ground Motions
October 1, 2024 - ASTM International

1.1 This practice covers the installation of suspended systems for acoustical tile and lay-in panels and their additional requirements for two groups of buildings that are constructed to resist the effects of earthquake motions as defined by ASCE 7 and the International Building Code. These...

ASTM F384-24 - Standard Specifications and Test Methods for Metallic Angled Orthopedic Fracture Fixation Devices
August 15, 2024 - ASTM International

1.1 These specifications and test methods provide a comprehensive reference for angled devices used in the surgical internal fixation of the skeletal system. This standard establishes consistent methods to classify and define the geometric and performance characteristics of angled devices. This...

ASTM F1575/F1575M-24 - Standard Test Method for Determining Bending Yield Moment of Nails, Spikes, and Dowel-type Threaded Fasteners
February 1, 2024 - ASTM International

5.1 Nails, spikes, and dowel-type threaded fasteners are common mechanical fasteners in wood structures. Engineering design procedures used to determine the capacities of laterally-loaded connections with these types of fasteners rely on a yield theory to establish the nominal resistance. In...

Advertisement