5.1 This practice documents cyclic performance benchmarks for shear walls constructed with wood structural panel (WSP) sheathing attached to dimension lumber framing using common or galvanized box nails as defined in 3.2.8. 5.2 Procedures described in this practice provide a method to...
This specification covers the minimum requirements for, and methods of, application of gypsum veneer base for gypsum veneer plasters. Details of construction for a specific assembly to achieve the required fire resistance shall be obtained from reports of fire-resistance tests, engineering...
1.1 This specification covers polymer modified bituminous sheet materials intended for use as underlayment on roof eaves, or valleys, or both, to prevent leakage of shingle, tile, or metal roofs from water back-up due to ice dams. 1.2 These underlayment sheets have a sticky adhesive layer which is...
1.1 These test methods provide a basic procedure for evaluating the withdrawal and lateral resistance of fasteners installed in wood and wood-based materials. Spikes are included as nails in this standard. 1.2 The tests also provide a basis for determining comparable performance of different...
This specification covers the installation of lathing and furring to receive interior and exterior Portland cement-based plaster. The following materials shall be used: metal plaster bases-expanded metal lath and wire laths; accessories-steel, PVC plastic, zinc alloy, and cornerite;...
This specification covers requirements for the methods of application and finishing of gypsum board. Construction details for a specific assembly to achieve the required fire resistance shall be obtained from reports of fire-resistance tests, engineering evaluations, or listings from recognized...
This specification covers the installation of lathing and furring to receive interior and exterior Portland cement-based plaster. The following materials shall be used: metal plaster bases-expanded metal lath and wire laths; accessories-steel, PVC plastic, zinc alloy, and cornerite;...
This specification establishes requirements and test methods for the materials, dimensions, warp, shrinkage, impact strength, expansion, appearance, and windload resistance of extruded single-wall siding manufactured from rigid (unplasticized) PVC compound. The siding shall be made of one or more...
1.1 This specification covers soft, medium, and hard temper zinc-coated (galvanized) carbon steel wire in coils for general use. 1.2 The supplementary requirements of this specification cover zinc-coated weights [masses] for nails, staples, and wire from which nails and staples are...
This specification covers glass fiber reinforced gypsum (GRG) composites suitable for producing GRG parts for non-loading bearings, thin sections, and ornamental shapes for architectural embellishment of interior building construction. Both the neat alpha gypsum cement and the resulting composite...
1.1 These test methods cover the determination of various strength and related properties of wood by testing small clear specimens. 1.1.1 These test methods represent procedures for evaluating the different mechanical and physical properties, controlling factors such as specimen size, moisture...
This specification covers standardizing the dimensions and materials for the manufacture of steel or cast iron shear plates used in the fabrication of connections in wood constructions. This specification covers the two basic diameters of metal shear plates commonly used in North American timber...
6.1 The resistance of plastic lumber and shapes to direct withdrawal of nails, staples, or screws is a measure of its ability to hold or be held to an adjoining object by means of such fasteners. Factors that affect this withdrawal resistance include the physical and mechanical properties of...
1.1 These test methods cover the physical testing of gypsum panel products. 1.2 The test methods appear in the following order: Section Flexural Strength (Method A) ?7 Core, End and Edge Hardness (Method A) ?8 Nail Pull Resistance (Method A) ?9 Flexural Strength (Method B) 11 Core, End and...
This specification covers the installation of lathing and furring to receive interior and exterior Portland cement-based plaster. The following materials shall be used: metal plaster bases-expanded metal lath and wire laths; accessories-steel, PVC plastic, zinc alloy, and cornerite;...
This specification covers requirements for the methods of application and finishing of gypsum board. Construction details for a specific assembly to achieve the required fire resistance shall be obtained from reports of fire-resistance tests, engineering evaluations, or listings from recognized...
This specification covers gypsum boards which include the following: gypsum wallboard for use on walls, ceilings, or partitions and that affords a surface suitable to receive decoration; predecorated gypsum board for use as the finished surfacing for walls, ceilings, or partitions; gypsum backing...
1.1 This practice covers the installation of suspended systems for acoustical tile and lay-in panels and their additional requirements for two groups of buildings that are constructed to resist the effects of earthquake motions as defined by ASCE 7 and the International Building Code. These...
1.1 These specifications and test methods provide a comprehensive reference for angled devices used in the surgical internal fixation of the skeletal system. This standard establishes consistent methods to classify and define the geometric and performance characteristics of angled devices. This...
5.1 Nails, spikes, and dowel-type threaded fasteners are common mechanical fasteners in wood structures. Engineering design procedures used to determine the capacities of laterally-loaded connections with these types of fasteners rely on a yield theory to establish the nominal resistance. In...
Narrow Your Results