2.1 The proper preparation of nickel alloy surfaces for nickel electroplating is often critical to the plating's performance. 2.2 This practice outlines recommended procedures to produce adherent nickel electrodeposits on nickel alloy surfaces.
This specification covers the requirements for electrodeposited zinc nickel alloy coatings on metals. The zinc nickel coating shall be defined as Class 1. The five chromate conversion coating types shall be defined as follows: Type A shall be with colorless conversion coatings,...
This specification covers nickel alloy forgings. These alloys are classified into different grades according to their chemical composition. A chemical analysis shall be employed on each alloy in order to determine its chemical composition. Grain size and mechanical...
1.1 This specification covers rolled nickel-chromium-aluminum alloys (UNS N06699), nickel-chromium-iron alloys (UNS N06600, N06601, N06603, N06690, N06693, N06025, N06045, and N06696), nickel-chromium-cobalt-mol
This specification covers nickel, nickel-copper, nickel-copper-silicon, nickel-molybdenum, nickel-chromium, and nickel-molybdenum-chromium
This specification covers UNS N06002, UNS N06030, UNS N06035, UNS N06022, UNS N06200, UNS N06230, UNS N06600, UNS N06617, UNS N06625, UNS N08020, UNS N08026, UNS N08024, UNS N08120, UNS N08926, UNS N08367, UNS N10242, UNS N10276, UNS N10665, UNS N10675, UNS N12160, UNS R20033, UNS N06059, UNS...
This guide covers standard specification for chromium-nickel alloy castings intended for heat-resisting and elevated-temperature
1.1 This specification2 covers nickel-chromium-aluminum alloy, nickel-chromium-iron alloys,3 nickel-chromium-cobalt-mol
This specification covers seamless tubes of nickel and nickel alloy for use in condenser and heat-exchanger service. This covers outside diameter and average wall, or outside diameter and minimum wall tube. Tube shall be furnished in the alloys and conditions defined by...
1.1 This specification covers rolled precipitation hardenable nickel-iron-chromium-niobi
1.1 This specification covers the requirements for copper-nickel alloy castings with nominal compositions shown in Table 1. 1.2 Castings of these alloys are used primarily for corrosion-resistance
1.1 This specification covers wrought welding fittings for pressure piping, factory-made from nickel and nickel alloys. Threaded fittings as covered in ASME B16.11 are also covered by this specification. The term welding applies to butt-welding or socket-welding parts such as...
5.1 This test method is used for the determination of phosphorus in nickel, ferronickel, and nickel alloy samples by spectrophotometric absorption to check for compliance with compositional specifications. It is assumed that all who use the procedure will be trained analysts...
1.1 This test method covers analysis of nickel alloys by flame atomic absorption spectrometry (FAAS) for the following elements: Element Compostiton Range, % Aluminum 0.2 to 4.0 Chromium 0.01 to 4.0 Cobalt 0.01 to 4.0 Copper 0.01 to 4.0 Iron 0.1 to 4.0 Manganese 0.1 to 4.0 Silicon 0.2...
1.1 This specification covers nickel-chromium-molybdenum
This specification covers the requirements for electrodeposited zinc nickel alloy coatings on metals. The zinc nickel coating shall be defined as Class 1. The five chromate conversion coating types shall be defined as follows: Type A shall be with colorless conversion coatings,...
5.1 This test method for the chemical analysis of nickel and nickel alloys is primarily intended to test material for compliance with specifications such as those under jurisdiction of ASTM committee B02. It may also be used to test compliance with other specifications that are...
1.1 This specification covers rolled precipitation hardenable nickel alloy (N07718)2 plate, sheet, and strip in the annealed condition (temper). 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI...
1.1 This specification covers welded UNS N06219, UNS N06625, UNS N08642, UNS N08825, and UNS N08827 nickel alloy boiler, heat exchanger, and condenser tubes for general corrosion resisting and low or high-temperature service. 1.2 This specification covers tubes 1/8 in. to 5 in. (3...
This specification covers UNS N07716, N07725, N07773, N07776, N09777, and N09925 nickel alloy hot or cold finished rounds, squares, hexagons, rectangles, and cold finished wires. Bars should be supplied in solution treated conditions while wires should be in both solution-treated and...
Narrow Your Results