loading
ASTM C430-26 - Standard Test Method for Fineness of Hydraulic Cement by the 45-μm (No. 325) Sieve
June 1, 2026 - ASTM International

This test method covers hydraulic cement fineness tests performed using a sieve. The sieve frame should be made of a circular metal matching the specified dimensions, fitted with either a stainless steel woven-wire sieve cloth or an electroformed forced nickel sieve sheet. Both the nozzle...

ASTM G211-14(2026) - Standard Test Method for Conducting Elevated Temperature Erosion Tests by Solid Particle Impingement Using Gas Jets
July 1, 2026 - ASTM International

1.1 This test method is concerned with the determination of material loss by gas-entrained solid particle impingement erosion with jet nozzle type erosion equipment. This test method can be used in the laboratory to measure the solid particle erosion of different materials and has been used...

ASTM C1014-26 - Standard Specification for Spray-Applied Mineral Fiber Thermal and Sound Absorbing Insulation
January 1, 2026 - ASTM International

This specification covers the composition and the physical properties of spray-applied mineral fiber thermal and sound absorbing insulation. These mineral fibers shall be pneumatically conveyed to a spray nozzle where they are mixed with water. These mineral fibers shall have a binder either...

ASTM E641-25 - Standard Methods for Testing Hydraulic Spray Nozzles Used in Agriculture
October 1, 2025 - ASTM International

1.1 These methods cover procedures for testing hydraulic spray nozzles used in agriculture. The methods herein cover the following performance parameters: nozzle flow rate, nozzle spray angle, liquid distribution, spray droplet size, and nozzle wearability. 1.2 These...

ASTM D8326-25 - Standard Practice for Measurement of the Kinetic Energy of Simulated Rainfall
December 1, 2025 - ASTM International

1.1 This practice is used to measure the kinetic energy of rainfall simulators used by laboratories to evaluate soil erosion. The kinetic energy of raindrops is an important factor that should be considered when conducting soil erosion studies. Using the data collected from determining the raindrop...

ASTM E1067/E1067M-25 - Standard Practice for Acoustic Emission Examination of Fiberglass Reinforced Plastic Resin (FRP) Tanks/Vessels
September 1, 2025 - ASTM International

5.1 The AE examination method detects damage in FRP equipment. The damage mechanisms that are detected in FRP are as follows: resin cracking, fiber debonding, fiber pullout, fiber breakage, delamination, and bond failure in assembled joints (for example, nozzles, manways, and so forth)....

ASTM A511/A511M-25 - Standard Specification for Seamless Stainless Steel Mechanical Tubing and Hollow Bar
September 1, 2025 - ASTM International

1.1 This specification covers seamless stainless tubing for use in mechanical applications or as hollow bar for use in the production of hollow components such as, but not limited to nozzles, reducers, and couplings by machining where corrosion-resistant or high-temperature strength is...

ASTM D5852/D5852M-25 - Standard Test Method for Erodibility Determination of Cohesive Soils in the Field and in the Laboratory Using the Submerged Jet Erosion Test
September 1, 2025 - ASTM International

1.1 These test methods cover the estimation of erodibility of a soil by the submerged Jet Erosion Test (JET) method, addressing devices of two different sizes. Test Method A uses a device with a 0.25-in. [6.35-mm]-diameter jet nozzle and a 12-in. [305-mm] diameter submergence tank to confine...

ASTM E1930/E1930M-25 - Standard Practice for Examination of Liquid-Filled Atmospheric and Low-Pressure Metal Storage Tanks Using Acoustic Emission
September 1, 2025 - ASTM International

5.1 General-This procedure is used for evaluation of the structural integrity of atmospheric storage tanks. The AE method can detect flaws which are in locations that are stressed during pressurization. Such locations include the tank wall, welds attaching pads to the tank, nozzle...

ASTM D6913/D6913M-17(2025) - Standard Test Methods for Particle-Size Distribution (Gradation) of Soils Using Sieve Analysis
October 1, 2025 - ASTM International

1.1 Soils consist of particles with various shapes and sizes. This test method is used to separate particles into size ranges and to determine quantitatively the mass of particles in each range. These data are combined to determine the particle-size distribution (gradation). This test method uses a...

ASTM D7109-25 - Standard Test Method for Shear Stability of Polymer-Containing Fluids Using a European Diesel Injector Apparatus at 30 Cycles and 90 Cycles
July 1, 2025 - ASTM International

5.1 This test method evaluates the percent viscosity loss of fluids resulting from physical degradation in the high shear nozzle device. Thermal or oxidative effects are minimized. 5.2 This test method may be used for quality control purposes by manufacturers of polymeric lubricant additives...

ASTM C430-25 - Standard Test Method for Fineness of Hydraulic Cement by the 45-μm (No. 325) Sieve
April 1, 2025 - ASTM International

This test method covers hydraulic cement fineness tests performed using a sieve. The sieve frame should be made of a circular metal matching the specified dimensions, fitted with either a stainless steel woven-wire sieve cloth or an electroformed forced nickel sieve sheet. Both the nozzle...

ASTM C786/C786M-25 - Standard Test Method for Fineness of Hydraulic Cement and Raw Materials by the 300-μm (No. 50), 150-μm (No. 100), and 75-μm (No. 200) Sieves by Wet Methods
April 1, 2025 - ASTM International

This test method covers wet sieving techniques for determination of fineness of hydraulic cement and raw materials by means of the No. 50, No. 100, and No. 200 sieves. The following apparatus shall be utilized: wet test sieves; spray nozzle; pressure gage; balance; weights; brush; dry test...

ASTM D7836-13(2025) - Standard Test Methods for Measurement of Yield Stress of Paints, Inks and Related Liquid Materials
May 1, 2025 - ASTM International

5.1 The yield stress of a material is a measure of the amount of force required to initiate movement of that material in a pipe, through a pump, or from nozzle. The yield stress also characterizes the ability of the material to maintain particles in suspension. Along with viscosity...

ASTM D7872-25 - Standard Test Method for Determining the Concentration of Pipeline Drag Reducer Additive in Aviation Turbine Fuels
May 1, 2025 - ASTM International

5.1 DRA is frequently added into multiproduct pipelines to increase throughput or reduce energy requirements of fuel movement. Although these additives are not used in jet fuel, contamination can occur from other products if proper batching guidelines are not followed or by other cases of human...

ASTM F1334-25 - Standard Test Method for Determining A-weighted Sound Power Level of Vacuum Cleaners
May 1, 2025 - ASTM International

1.1 This test method calculates the overall A-weighted sound power level emitted by small portable upright, canister, combination vacuum cleaners, backpack vacuum cleaners, hard-floor cleaning machines, extractors, and central vacuum cleaner motorized nozzles intended for operation in...

UL 2586A - Hose Nozzle Valves for Gasoline and Gasoline/Ethanol Blends with Nominal Ethanol Concentrations up to 85 Percent (E0 - E85)
May 31, 2024 - ULSE

1.1 These requirements cover hose nozzle valves that are intended to be used for the control of motor fuels as indicated in 2. They are of the type used in motor fuel dispensing equipment. Hose nozzle valves covered by this standard are for use with motor fuels which are handled at...

ULC 2586A - Hose Nozzle Valves for Gasoline and Gasoline/Ethanol Blends with Nominal Ethanol Concentrations up to 85 Percent (E0 - E85)
May 31, 2024 - ULSE

1.1 These requirements cover hose nozzle valves that are intended to be used for the control of motor fuels as indicated in 2. They are of the type used in motor fuel dispensing equipment. Hose nozzle valves covered by this standard are for use with motor fuels which are handled at...

ASTM F2014-00(2024) - Standard Specification for Non-Reinforced Extruded Tee Connections for Piping Applications
November 15, 2024 - ASTM International

This specification covers the pipe materials and dimensions for producing non-reinforced extruded tee connections manufactured by mechanical forming processes. The term "extruded tee connection" applies to butt-weld or socket-weld connections. The non-reinforced extruded pipe tee connection is an...

UL 2586B - Hose Nozzle Valves for Diesel Fuel, Biodiesel Fuel, Diesel/Biodiesel Blends with Nominal Biodiesel Concentrations up to 20 Percent (B20), Kerosene, and Fuel Oil
May 31, 2024 - ULSE

1.1 These requirements cover hose nozzle valves that are intended to be used for the control of motor fuels as indicated in 2. They are of the type used in motor fuel dispensing equipment. Hose nozzle valves covered by this standard are for use with motor fuels which are handled at...

Advertisement