This test method covers hydraulic cement fineness tests performed using a sieve. The sieve frame should be made of a circular metal matching the specified dimensions, fitted with either a stainless steel woven-wire sieve cloth or an electroformed forced nickel sieve sheet. Both the nozzle...
1.1 This test method is concerned with the determination of material loss by gas-entrained solid particle impingement erosion with jet nozzle type erosion equipment. This test method can be used in the laboratory to measure the solid particle erosion of different materials and has been used...
This specification covers the composition and the physical properties of spray-applied mineral fiber thermal and sound absorbing insulation. These mineral fibers shall be pneumatically conveyed to a spray nozzle where they are mixed with water. These mineral fibers shall have a binder either...
1.1 These methods cover procedures for testing hydraulic spray nozzles used in agriculture. The methods herein cover the following performance parameters: nozzle flow rate, nozzle spray angle, liquid distribution, spray droplet size, and nozzle wearability. 1.2 These...
1.1 This practice is used to measure the kinetic energy of rainfall simulators used by laboratories to evaluate soil erosion. The kinetic energy of raindrops is an important factor that should be considered when conducting soil erosion studies. Using the data collected from determining the raindrop...
5.1 The AE examination method detects damage in FRP equipment. The damage mechanisms that are detected in FRP are as follows: resin cracking, fiber debonding, fiber pullout, fiber breakage, delamination, and bond failure in assembled joints (for example, nozzles, manways, and so forth)....
1.1 This specification covers seamless stainless tubing for use in mechanical applications or as hollow bar for use in the production of hollow components such as, but not limited to nozzles, reducers, and couplings by machining where corrosion-resistant or high-temperature strength is...
1.1 These test methods cover the estimation of erodibility of a soil by the submerged Jet Erosion Test (JET) method, addressing devices of two different sizes. Test Method A uses a device with a 0.25-in. [6.35-mm]-diameter jet nozzle and a 12-in. [305-mm] diameter submergence tank to confine...
5.1 General-This procedure is used for evaluation of the structural integrity of atmospheric storage tanks. The AE method can detect flaws which are in locations that are stressed during pressurization. Such locations include the tank wall, welds attaching pads to the tank, nozzle...
1.1 Soils consist of particles with various shapes and sizes. This test method is used to separate particles into size ranges and to determine quantitatively the mass of particles in each range. These data are combined to determine the particle-size distribution (gradation). This test method uses a...
5.1 This test method evaluates the percent viscosity loss of fluids resulting from physical degradation in the high shear nozzle device. Thermal or oxidative effects are minimized. 5.2 This test method may be used for quality control purposes by manufacturers of polymeric lubricant additives...
This test method covers hydraulic cement fineness tests performed using a sieve. The sieve frame should be made of a circular metal matching the specified dimensions, fitted with either a stainless steel woven-wire sieve cloth or an electroformed forced nickel sieve sheet. Both the nozzle...
This test method covers wet sieving techniques for determination of fineness of hydraulic cement and raw materials by means of the No. 50, No. 100, and No. 200 sieves. The following apparatus shall be utilized: wet test sieves; spray nozzle; pressure gage; balance; weights; brush; dry test...
5.1 The yield stress of a material is a measure of the amount of force required to initiate movement of that material in a pipe, through a pump, or from nozzle. The yield stress also characterizes the ability of the material to maintain particles in suspension. Along with viscosity...
5.1 DRA is frequently added into multiproduct pipelines to increase throughput or reduce energy requirements of fuel movement. Although these additives are not used in jet fuel, contamination can occur from other products if proper batching guidelines are not followed or by other cases of human...
1.1 This test method calculates the overall A-weighted sound power level emitted by small portable upright, canister, combination vacuum cleaners, backpack vacuum cleaners, hard-floor cleaning machines, extractors, and central vacuum cleaner motorized nozzles intended for operation in...
1.1 These requirements cover hose nozzle valves that are intended to be used for the control of motor fuels as indicated in 2. They are of the type used in motor fuel dispensing equipment. Hose nozzle valves covered by this standard are for use with motor fuels which are handled at...
1.1 These requirements cover hose nozzle valves that are intended to be used for the control of motor fuels as indicated in 2. They are of the type used in motor fuel dispensing equipment. Hose nozzle valves covered by this standard are for use with motor fuels which are handled at...
This specification covers the pipe materials and dimensions for producing non-reinforced extruded tee connections manufactured by mechanical forming processes. The term "extruded tee connection" applies to butt-weld or socket-weld connections. The non-reinforced extruded pipe tee connection is an...
1.1 These requirements cover hose nozzle valves that are intended to be used for the control of motor fuels as indicated in 2. They are of the type used in motor fuel dispensing equipment. Hose nozzle valves covered by this standard are for use with motor fuels which are handled at...
Narrow Your Results