FOREWORD: Each year in the United States several thousand wells are drilled and completed - some productive of oil or gas and some dry - and during this drilling and completion most of these wells are cased, with the casing set in the bore hole surrounded by oil-well cement. This book...
1.1 This test method2 covers the determination of the compatibility of automotive gear oils with specific nitrile, polyacrylate, and fluoroelastomer oil seal materials. 1.2 Users of this test method should obtain Test Methods D412, D471, and D2240 and become familiar with their use...
1. SCOPE: The material defined by this specification is a polyacrylic rubber compound suitable for oil seals.
5.1 Some engine oil formulations have been shown to lack compatibility with certain elastomers used for seals in automotive engines. These deleterious effects on the elastomer are greatest with new engine oils (that is, oils that have not been exposed to an engine's operating...
1.0 SCOPE This specification covers the requirements for radial lip oil seals used in the Company's products to retain lubricants and exclude dirt particles, water and other contaminants.
1.1 This test method2 covers the determination of the compatibility of automotive gear oils with specific nitrile, polyacrylate, and fluoroelastomer oil seal materials. 1.2 Users of this test method should obtain Test Methods D412, D471, and D2240 and become familiar with their use...
1.1 This test method2 covers the determination of the compatibility of automotive gear oils with specific nitrile, polyacrylate, and fluoroelastomer oil seal materials. 1.2 Users of this test method should obtain Test Methods D412, D471, and D2240 and become familiar with their use...
This test method2 covers the determination of the compatibility of automotive gear oils with specific nitrile, polyacrylate, and fluoroelastomer oil seal materials. Users of this test method should obtain Test Methods D412, D471, and D2240 and become familiar with their use before...
5.1 Analyzing in-service lubricating oil and hydraulic fluid samples is crucial for assessing the condition of both the fluid and the equipment. The results of the fluid analysis guide the planning of any necessary corrective maintenance activities. 5.2 The objective of this guide is to...
5.1 Some engine oil formulations have been shown to lack compatibility with certain elastomers used for seals in automotive engines. These deleterious effects on the elastomer are greatest with new engine oils (that is, oils that have not been exposed to an engine's operating...
5.1 This practice allows for compositional analysis of the gases in equilibrium with crude oil, condensate, and liquid petroleum products at a 4:1 vapor/liquid ratio at ambient temperature for analysis using typical instrumentation (RGA) already available in typical refinery laboratories....
5.1 This guide is intended to provide machinery maintenance and monitoring personnel with a guideline for performing filter debris analysis as a means to determine machine condition. Correlating the filter contaminants to 'normal' and 'abnormal' lube system operation provides early indication of a...
1.1 This test method2 covers the determination of the compatibility of automotive gear oils with specific nitrile, polyacrylate, and fluoroelastomer oil seal materials. 1.2 Users of this test method should obtain Test Methods D412, D471, and D2240 and become familiar with their use...
PURPOSE AND USE OF PROCESS INDUSTRY PRACTICES In an effort to minimize the cost of process industry facilities, this Practice has been prepared from the technical requirements in the existing standards of major industrial users, contractors, or standards organizations. By harmonizing these...
This material has resistance to diester-based engine oil (MIL-PRF-7808) and fuel, but usage is not limited to such applications. This material is not suitable for use in synthetic phosphate ester based hydraulic fluids (AS1241) or helicopter transmission lubricating oils (DOD-PRF-85734,...
1.1 This test method2 covers the determination of the compatibility of automotive gear oils with specific nitrile, polyacrylate, and fluoroelastomer oil seal materials. 1.2 Users of this test method should obtain Test Methods D412, D471, and D2240 and become familiar with their use...
1.1 This specification covers preformed rubber gaskets used to seal joints in cast iron soil pipe and fittings. 1.2 The committee with jurisdiction over this standard is not aware of another comparable standard for materials covered in this standard. 1.3 The values stated in inch-pound units...
This specification covers the material requirements for preformed polychloroprene elastomeric joint seals for concrete pavements. The seal consists of a multiple web design and is installed with a lubricant. The seal functions by compression of the seal between the faces...
Narrow Your Results