loading
API OIL WELL CEMENT - OIL-WELL CEMENTING PRACTICES IN THE UNITED STATES
January 1, 1959 - API

FOREWORD: Each year in the United States several thousand wells are drilled and completed - some productive of oil or gas and some dry - and during this drilling and completion most of these wells are cased, with the casing set in the bore hole surrounded by oil-well cement. This book...

GREEN VEGETABLE OIL PROCE - GREEN VEGETABLE OIL PROCESSING
AOCS
A description is not available for this item.
ASTM D5958-99(2026) - Standard Practices for Preparation of Oil-Based Ink Resin Solutions
June 1, 2026 - ASTM International

1.1 These practices describe laboratory procedures for preparing an oil-based ink resin solution in a high-boiling solvent using four pieces of lab equipment: (1) A hot oil bath (Sections 4 to 11), (2) A stirrer/hot plate (Sections 12 to 16), (3) An industrial blender (Sections 17 to...

ASTM D4807-26 - Standard Test Method for Sediment in Crude Oil by Membrane Filtration
June 1, 2026 - ASTM International

5.1 A knowledge of the sediment content of crude oil is important both in refinery operations and in crude oil commerce.

ASTM D6871-26 - Standard Specification for Natural (Vegetable Oil) Ester Fluids Used in Electrical Apparatus
June 1, 2026 - ASTM International

1.1 This specification covers a high fire point natural vegetable oil ester insulating fluid for use as a dielectric and cooling medium in new and existing power and distribution electrical apparatus such as transformers and attendant equipment. 1.2 Natural vegetable oil ester...

ASTM D613-26 - Standard Test Method for Cetane Number of Diesel Fuel Oil
June 1, 2026 - ASTM International

1.1 This test method covers the determination of the rating of diesel fuel oil in terms of an arbitrary scale of cetane numbers using a standard single cylinder, four-stroke cycle, variable compression ratio, indirect injected diesel engine. 1.2 The cetane number scale covers the range from...

ASTM D2414-26 - Standard Test Method for Carbon Black—Oil Absorption Number (OAN)
May 1, 2026 - ASTM International

1.1 This test method covers the determination of the oil absorption number of carbon black. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety...

ASTM D6583-13(2026) - Standard Test Method for Porosity of Paint Film by Mineral Oil Absorption
June 1, 2026 - ASTM International

1.1 This test method is applicable to air-dry architectural coatings of any type, both solvent and water-borne, and of any color, dark as well as light. It cannot be used with films that are dissolved or excessively softened by mineral oil, but practical examples of such films will be...

ASTM D2226-93(2026) - Standard Classification for Various Types of Petroleum Oils for Rubber Compounding Use
July 1, 2026 - ASTM International

1.1 This classification is intended to establish classification and test methods for certain types of oil used in extending and processing styrene-butadiene rubbers (SBR) and butadiene rubbers (BR). Its purpose is for classification only and not for specification. 1.2 This standard may...

ASTM D8193-26 - Standard Test Method for Total Oil and Grease (TOG) and Total Petroleum Hydrocarbon (TPH) in Water and Wastewater with Solvent Extraction Using Non-Dispersive Mid-IR Transmission Spectroscopy
May 15, 2026 - ASTM International

1.1 This test method covers the determination of total oil and grease (TOG) that can be extracted from water or wastewater samples by cyclohexane and measured by non-dispersive IR spectroscopy from 1370?cm-1 to 1380?cm-1. Treating the extract with Florisil to remove polar substances prior to...

ASTM C1277-26 - Standard Specification for Shielded Couplings Joining Hubless Cast Iron Soil Pipe and Fittings
July 15, 2026 - ASTM International

This specification covers the materials and testing of shield hubless couplings to join hubless cast iron soil pipe and fittings. Gaskets shall comply with the required physical and chemical properties, dimensions, and material specifications. The rubber gasket shall conform to the required...

ASTM D8665-26 - Standard Test Method for Measuring the Gelation Propensity of Automotive Engine Oils After Treatment with Acidified Water
June 1, 2026 - ASTM International

5.1 It is normal for some of the combustion products of an internal combustion engine, such as carbon dioxide, to penetrate the engine oil and be retained in it. 5.2 When an engine is run for a period and then stored over a long period of time, the by-products of combustion might be retained...

ASTM D6794-26 - Standard Test Method for Measuring the Effect on Filterability of Engine Oils After Treatment with Various Amounts of Water and a Long (6?h) Heating Time
June 1, 2026 - ASTM International

1.1 This test method covers the determination of the tendency of an oil to form a precipitate that can plug an oil filter. It simulates a problem that may be encountered in a new engine run for a short period of time, followed by a long period of storage with some water in the...

ASTM D6795-26 - Standard Test Method for Measuring the Effect on Filterability of Engine Oils After Treatment with Water and Dry Ice and a Short (30?min) Heating Time
June 1, 2026 - ASTM International

1.1 This test method covers the determination of the tendency of an oil to form a precipitate that can plug an oil filter. It simulates a problem that may be encountered in a new engine run for a short period of time, followed by a long period of storage with some water in the...

ASTM D3427-26 - Standard Test Method for Air Release Properties of Hydrocarbon Based Oils
June 1, 2026 - ASTM International

5.1 Agitation of lubricating oil with air in equipment, such as bearings, couplings, gears, pumps, and oil return lines, may produce a dispersion of finely divided air bubbles in the oil. If the residence time in the reservoir is too short to allow the air bubbles to rise to...

ASTM D2595-26 - Standard Test Method for Evaporation Loss of Lubricating Greases Over Wide-Temperature Range
July 1, 2026 - ASTM International

5.1 The loss of volatile materials from greases and oils can adversely affect the original performance characteristics of a lubricant and, therefore, could be a significant factor in evaluating a lubricant for a specific use. Such volatiles can also be considered contaminants in the environment in...

ASTM D3230-26 - Standard Test Method for Salts in Crude Oil (Electrometric Method)
March 1, 2026 - ASTM International

1.1 This test method covers the determination of the approximate chloride (salts) concentration in crude oil. The range of concentration covered is 3.5?mg/kg to 500?mg/kg or 1.0?lb/1000 bbl to 150?lb/1000 bbl (PTB) as chloride concentration/volume of crude oil. 1.2 This test method...

Advertisement