This specification covers one type of humidifier for use in the operating rooms of the Medical Unit - Self Contained Transportable (MUST).
3.1 Hospital receiving personnel, central supply personnel, operating room personnel, surgeons, and occasionally other individuals will handle orthopedic implants and instruments. All personnel should be informed of recommended care and handling procedures to prevent damage or loss to...
5.1 This practice determines the room temperature gasket constants Gb and a for initial seating and Gs for operating conditions as related to the tightness behavior of pressurized bolted flanged connections. These constants are used in determining the design bolt load for gasketed...
1.1 This test method describes the assessment of material thermal stability through the determination of the temperature at which the materials start to decompose or react and the extent of the mass change using thermogravimetry. The test method uses minimum quantities of material and is applicable...
5.1 This guide is intended for the developers or sponsors of new aviation gasolines or additives to describe the data requirements necessary to support the development of specifications for these new products by ASTM members. The ultimate goal of the data generated in accordance with this guide is...
4.1 The ability of a plastic material to resist deterioration caused by exposure to light, heat, and water is a property of significance in many applications. This practice is intended to induce property changes associated with end-use conditions, including the effects of ultraviolet solar...
1.1 This test method covers the fueling and operating protocol for determining particulate matter emissions from wood fires in wood-burning room heaters and fireplace inserts as well as determining heat output and efficiency. 1.2 The values stated in SI units are to be regarded as the...
1.1 This test method covers the fueling and operating protocol for determining particulate matter emissions from fires in pellet or other granular or particulate biomass burning room heaters and fireplace inserts. 1.2 The values stated in SI units are to be regarded as standard. The...
1.1 The goal of this guide is to recommend a universal label format (across manufacturers and various implants) of content and relative location of information necessary for final implant selection within an implant's overall package labeling. 1.2 This guide recommends package labeling for...
5.1 Bacteria that exist in biofilms are phenotypically different from suspended cells of the same genotype. Research has shown that biofilm bacteria are more difficult to kill than suspended bacteria (4, 5). Laboratory biofilms are engineered in growth reactors designed to produce a specific...
5.1 The spectrum of the noise produced in the receiving room by the standard tapping machine is determined by (1) the size and the mechanical properties of the floor-ceiling assembly, such as its weight, surface properties, mounting or edge restraints, stiffness, and internal damping; (2)...
1.1 When conducting test methods, it is important to consider the role that the environmental conditions play in measurement of exoskeleton safety and performance. Exoskeletons are designed to be operated both indoors and outdoors under conditions specified by the manufacturer. Likewise, end...
4.1 Addressing consensus standards with inter-laboratory studies (ILS) and methods specific to an organization. Test methods need to be validated in many cases, in order to be able to rely on the results. This has to be done at the organization performing the tests but is also performed in the...
1.1 This practice covers basic principles and operating procedures for testing water resistance of coatings using single-sided, controlled condensation. 1.2 Condensation is produced by exposing one surface of a coated specimen to a heated, saturated mixture of air and water vapor, while the...
1.1 This practice covers the basic principles and operating procedures for testing water resistance of coatings by exposing coated specimens in an atmosphere maintained at 100?% relative humidity so that condensation forms on all surfaces of test specimens. 1.2 This practice uses the...
1.1 This test method covers the determination of the bonding strength of air-setting refractory mortar by determining the flexural strength (modulus of rupture) at room temperature of oven-dried brick-mortar joints. 1.2 The values stated in inch-pound units are to be regarded as standard....
5.1 This guide is intended for the developers or sponsors of new aviation gasolines or additives to describe the data requirements necessary to support the development of specifications for these new products by ASTM members. The ultimate goal of the data generated in accordance with this guide is...
5.1 This guide is intended for the developers or sponsors of new aviation gasolines or additives to describe the data requirements necessary to support the development of specifications for these new products by ASTM members. The ultimate goal of the data generated in accordance with this guide is...
Narrow Your Results