5.1 Thermogravimetry provides a rapid method for determining the thermal decomposition and reaction mass change of a material. 5.2 This test method is useful in detecting potentially hazardous reactions and in estimating the temperatures at which these reactions occur. This test method is...
5.1 This practice determines the room temperature gasket constants Gb and a for initial seating and Gs for operating conditions as related to the tightness behavior of pressurized bolted flanged connections. These constants are used in determining the design bolt load for...
4.1 The ability of a plastic material to resist deterioration caused by exposure to light, heat, and water is a property of significance in many applications. This practice is intended to induce property changes associated with end-use conditions, including the effects of ultraviolet solar...
5.1 This guide is intended for the developers or sponsors of new aviation gasolines or additives to describe the data requirements necessary to support the development of specifications for these new products by ASTM members. The ultimate goal of the data generated in accordance with this guide is...
1.1 This practice specifies the parameters for growing a Pseudomonas aeruginosa (ATCC 154422) or Staphylococcus aureus (ATCC 65382) biofilm that can be used for disinfectant efficacy testing using the Test Method for Evaluating Disinfectant Efficacy Against Biofilm Grown in CDC Biofilm Reactor...
1.1 When conducting test methods, it is important to consider the role that the environmental conditions play in measurement of exoskeleton safety and performance. Exoskeletons are designed to be operated both indoors and outdoors under conditions specified by the manufacturer. Likewise, end...
4.1 Addressing consensus standards with inter-laboratory studies (ILS) and methods specific to an organization. Test methods need to be validated in many cases, in order to be able to rely on the results. This has to be done at the organization performing the tests but is also performed in the...
1.1 This practice covers basic principles and operating procedures for testing water resistance of coatings using single-sided, controlled condensation. 1.2 Condensation is produced by exposing one surface of a coated specimen to a heated, saturated mixture of air and water vapor, while the...
1.1 This practice covers the basic principles and operating procedures for testing water resistance of coatings by exposing coated specimens in an atmosphere maintained at 100?% relative humidity so that condensation forms on all surfaces of test specimens. 1.2 This practice uses the...
1.1 This test method covers the determination of the bonding strength of air-setting refractory mortar by determining the flexural strength (modulus of rupture) at room temperature of oven-dried brick-mortar joints. 1.2 The values stated in inch-pound units are to be regarded as...
5.1 This guide is intended for the developers or sponsors of new aviation gasolines or additives to describe the data requirements necessary to support the development of specifications for these new products by ASTM members. The ultimate goal of the data generated in accordance with this guide is...
5.1 This guide is intended for the developers or sponsors of new aviation gasolines or additives to describe the data requirements necessary to support the development of specifications for these new products by ASTM members. The ultimate goal of the data generated in accordance with this guide is...
This specification covers performance requirements for general purpose air ovens ordinarily used in testing operations, which have a testing chamber up to 0.6 cu. m (25 cu. ft.) in volume. It applies to gravity convection ovens designed to operate over all or part of the temperature...
5.1 The measured maximum energy input rate is used to confirm that the coffee brewer is operating in accordance with its nameplate rating. 5.2 If applicable and accessible, the boiler or internal tank temperature is measured to ensure that the water is maintained at a ready-to-brew...
5.1 This practice determines the room temperature gasket constants Gb and a for initial seating and Gs for operating conditions as related to the tightness behavior of pressurized bolted flanged connections. These constants are used in determining the design bolt load for...
5.1 This guide is intended for the developers or sponsors of new aviation gasolines or additives to describe the data requirements necessary to support the development of specifications for these new products by ASTM members. The ultimate goal of the data generated in accordance with this guide is...
1.1 These requirements apply to factory-built gas appliances having inputs of more than 400,000 Btu per hour, per individual combustion chamber which require flame failure and other precautions and which are intended primarily for commercial and industrial installation. The appliances covered by...
5.1 This guide is intended for the developers or sponsors of new aviation gasolines or additives to describe the data requirements necessary to support the development of specifications for these new products by ASTM members. The ultimate goal of the data generated in accordance with this guide is...
5.1 This standard provides a description of test methods used in other ASTM specifications to establish certain acceptable methods for characterizing thermocouple assemblies and thermocouple cable. These test methods define how those characteristics shall be determined. 5.2 The usefulness and...
Narrow Your Results